MyBabiie MBBC1 User manual

MBBC1 My Babiie Closer
Bedside Crib
IMPORTANT! KEEP FOR FUTURE REFERENCE
Suitable for use with beds that have a slatted frame

1
Bedside crib parts
Assembly and Use
2 x Feet
2 x bed fastening straps
Attach side arms into feet 2Join the 2 feet with the base
cross bar
Crib, including mattress Carry Bag
Base cross bar2 x Side arms
WARNING: make sure that the buckles are on
the same side as the adjustable feet

5
3Push the crib down onto
the 2 side arms. Ensure it clicks
into place securely both sides
Insert the included mattress Use the wheel locks on each
side to prevent the crib from
rolling
WARNING: When using as a standalone crib
(not bedside) ensure that both feet are fully
extended and locked
4Fasten the velcro fabric covers
on each side of the crib
6

8
The height of the crib can be
adjusted by simaltaneously
pressing the side buttons and
lifting. Ensure it has correctly
clicked into place before use
The crib can be inclined with a
maximum variance of 2
positions between one leg and
the other
7
9Co-Sleeping Mode (Fixing to the bed).
Read page 9 of this manual
10
11 Unattach the side panel

12b
12a12a
5
Pull to tighten and
bring crib next to bed
17a 17b
14
Loop the clip end around
the bed frame
15
Fasten the straps together
with the clips
16
Position the metal plate
against the bed
13a 13b 13c
Attaching the straps
Release the crib from
the side leg
Loop the strap around
the side leg
(one strap each side)
Reattach the
crib. Repeat
on other side
Tighten any remaining
slack so crib is secure
in place

6
WARNING: Once attached to the bed, you must ensure the crib is level
and not tilted at all and is completely flat to avoid baby from rolling.
Ensure crib is completely level
Min. 57cm - Max. 67.5cm
Min. 8cm
Max. 38cm
WARNING: Check that the strap adjusters are correctly fitted
to prevent loosening of the straps and creation of dangerous
gaps during use.

WARNING: BEFORE USE, REMOVE AND DISPOSE OF ALL PLASTIC BAGS AND PACKAGING MATERIALS AND
KEEP THEM OUT OF REACH OF CHILDREN.
WARNING: This product is intended for use for babies aged between 0 and 6 months, weighing up to a maximum of 9 kg.
WARNING: When a child is able to sit, kneel or to pull itself up, the product should not be used anymore for this child.
WARNING: Do not use the product when any part is broken, torn or missing. Do not replace missing, damaged or broken
parts with non-original components or components not approved by My Babiie.
WARNING: Read the instructions for use for the list of components. Examine the product regularly to make sure that
there are no loose, damaged or missing parts.
WARNING: Always use all parts needed for each configuration of use.
WARNING: Be aware of the risk of open fires and other sources of strong heat, such as electricbar fires, gas fires, etc.
· Before assembly, check that the product and all of its components have not been damaged during transportation.
Should any part be damaged do not use and keep out of reach of children.
· Make sure that the person using the product knows how to do it in the safest way.
WARNING: The product is ready for use only when the locking mechanisms are engaged. Make sure they are securely
fixed before use.
WARNING: When your child is unattended in the product in “crib configuration”, always make sure that the side is raised
and the zippers are closed completely.
· When the product is being used, and above all in “crib configuration”, the wheels must always be locked.
· All operations for opening, adjusting, fastening and positioning the product must be carried out by an adult.
· Before using in “Co-Sleeping configuration (fastened to bed),” make sure the product is fastened and positioned
correctly.
WARNING: To prevent the risk of trapping the child’s head, the crib in “Co-Sleeping configuration (fastened to the bed)”
must be duly fastened to parents’ bed according to the instructions for use with the fastening belts.
WARNING: When the product is used in “Co-Sleeping configuration (fastened to the bed),” before laying down your
child, make sure that the fastening belts are fastened and tightened correctly, the product must be fastened to the
mattress of the parents’ bed and there must be no gaps between the product and the mattress of the parents’ bed.
DO NOT use the product if there are any gaps.
· Do not fill any spaces or gaps between the parents’ mattress and the crib with pillows, blankets, bedsheets or any other
material that may cause the risk of suffocation.
WARNING: To avoid all risks of strangulation, on the top part of the side of the crib in contact with the parents’ bed, the
top edge of the lowered side of the crib must not be higher than the upper surface of the parents’ mattress.
· The product must always be placed on a horizontal surface. Do not place the product onto a sloped surface with your
child inside.
· Unattended children must not be left to play near the product.
· Do not use the product without the frame.
· Keep the fastening belts out of reach of children.
· Only use the mattress provided with the product or replacement mattresses approved by My Babiie.
· Do not use more than one mattress in the crib. Only use the mattress supplied with the crib.
WARNING: Do not to use the body of a cradle without its frame.
WARNING: The thickness of the mattress chosen shall be such that the internal vertical height (surface of the top of the
mattress to the upper edge of the bed sides) is at least 200 mm in the highest position of the bed base
EN 16890:2017
7

WARNING: check to make sure that all of the fasteners have been correctly attached and that the zips are closed and
locked right to the end of their travel.
WARNING: do not use the cot with adjustable feet partially or totally retracted and unlocked. In the case of accidental
knocks against adjustable feet, return them to the correct position by lifting the crib slightly.
WARNING: Only use the mattress sold with the crib. Do not add a second mattress, choking hazard.
· Newborn babies can suffocate on soft bedding. Avoid placing any pillow or similar items under sleeping infant for
additional comfort.
· The reference mark on the inner face of the product shows the maximum thickness of the mattress to use.
· Use the crib in “Co-Sleeping configuration (fastened to the bed)” only with beds of the size indicted in the reference
figure at the beginning of the manual.
· Do not leave anything inside the product that might reduce its depth.
· To prevent it becoming trapped, do not place the crib close to walls or obstacles.
· Do not leave any small objects inside the product that might be swallowed.
· Only use spare parts approved by the manufacturer.
Do not attach any accessories to the product that have not been supplied by the manufacturer.
· Do not make adjustments to the product when the child is in it.
· Do not move the product when the child is inside.
· Do not use the product for more than one child at a time.
· The product must be kept away from electrical cables and cords: do not position close to windows where cords, curtains
or similar could pose a suffocation or choking hazard. To avoid all risks of strangulation, never give children objects with
cords or strings attached, or leave them within their reach.
· Prolonged exposure to direct sunlight can cause the colours of the fabric to fade. After a prolonged exposure of the
product to high temperatures, wait a few minutes prior to putting your child in it.
· Keep the product out of reach of children when it is not in use.
HEIGHT ADJUSTMENT OF THE COT
The crib can be adjusted to different height positions. In order to adjust the height, pull the adjustment lever upwards
and lift the crib to the desired position (fig. 7). Repeat this operation on the opposite side.
The base of the crib can be inclined slightly by adjusting the 2 legs to different heights (fig. 8).
WARNING: the crib can be inclined with a maximum variance of 2 positions between one leg and the other (for
example: the right leg in position 3 and the left leg in position 1, see fig. 8).
WARNING: The head of the child should always be positioned on the highest side (fig. 9).
8

The crib can be fixed to the parent’s bed (co-sleeping mode). WARNING – IMPORTANT FOR THE SAFETY OF YOUR
CHILD: this method is only possible with bed types that comply with all of the conditions described in this paragraph. In
particular the side support of the crib should always be put close to the parent’s mattress and the mattress should always
be aligned with the height of the side support for restraint of the crib (see fig. 10). Furthermore, the crib should be firmly
fixed to the structure of the parents bed or to the mattress support (net or slats).
WARNING: Check to make sure that the crib in the co-sleeping mode does not interfere with the parent’s bed.
WARNING: During use, make sure that the parents bed sheets, blankets etc. do not enter and cover the interior of
the crib.
1. Open the side of the crib with the window using the side zips and open them completely (fig. 11). Then press the
removable tubular structure release button and remove partially on one side and then on the other. Once this operation
has been performed on both sides, lower the bar down to create the side opening.
WARNING: use the crib with the tube lowered, only in the co-sleeping mode.
2. Move the crib close to the parent’s bed and check the height of the crib compared with the mattress of the bed.
WARNING: the height of the parent’s mattress should always be more than that of the side support for containment of
the crib (fig. 12b).
WARNING: Revove the metal bar from the top of the fold down flap to allow crib to sit close to the bed mattress. (fig
12a). Store the metal bar somewhere safe so that it can be re-inserted when used as a stand alone crib.
WARNING: in the co-sleeping mode the 2 legs of the crib should always be adjusted to the same height.
3. In order to fix the crib to the parents bed (co-sleeping mode) use the pair of straps provided.
4. Loop the strap around the side legs of the crib. One strap on each side of the crib. (fig. 13)
5. Pass the belt around the structure of the parent’s bed (fig. 14). Repeat this operation on the other side. For easier
installation, during fixing of the buckles, we suggest that the crib is kept at a short distance from the parent’s bed.
6. Fasten the clips together (fig. 15)
7. Position the oval metal plate against the side of the bed (fig. 16). At this point, move the crib to the side of the parent’s
bed and tighten by pulling the belt firmly (fig. 17). Carry out this operation on one side and then on the other side,
adjusting the belts until the crib is firmly in contact with the parents mattress.
WARNING: before every use always check to make sure that there is no space between the parent’s mattress and the
side of the crib. If there is, pull the belts firmly to tighten until there’s no space and the permitted condition of use has
been restored.
WARNING: before every use always check to make sure that bedside crib is flat and level so that it is not tilted at all.
8. Store any excess of belts safely out of the way.
9. Lock the wheels of the crib.
If, during the fixing operations of the crib to the parent’s bed, it is not possible to slide the feet of the crib under the
parent’s bed, it is still possible to fix the crib following the operations described in the previous points as one side of the
cribs feet are on springs, allowing them to move inwards to allow the crib to be brought in close to the
parents bed. Make sure the wheels are locked into position before use.
WARNING: Use of the product is only permitted with beds and/or mattresses with straight sides. Use of the product with
round beds and/or mattresses or water beds is not permitted.
WARNING: When the product is used in the “Co-Sleeping Mode” (fixing to the bed), it should always be fitted to the long
side of access to the bed. DO NOT fix the product to the head or bottom of the bed.
Co-Sleeping Mode (Fixing to the bed)
9

MAINTENANCE ADVICE
The crib and the mattress have a resistant fabric cover, which is completely removable and washable.
The removal/application activities should be carried out by adults only. On a regular basis check the condition of the
product and the presence of any possible damage. In the case of damage do not use it and keep it out of the reach of
children.
For washing of the fabrics, carefully comply with the instructions indicated on the label.
For cleaning do not use solvents, abrasive products or aggressive products.
Hand wash in cold water
Do not bleach
Do not tumble dry
After each wash check the resistance of the fabric and of the stitching.
WARNING: During the removal and/or application of the lining, handle the fabric carefully in order to avoid accidental
damage or tears.
WARNING: The removal and/or application operations may take a few minutes and should be carried out by an adult.
MAKING THE BED
It is possible to unfasten the crib from the parents’ bed in order to make the bed easily. Just unfasten the buckles
located below the fabric finish.
To re-secure the crib to the parents’ bed, pull once again the belts to make sure the crib is properly and firmly secured
to the parents’ bed. Pay attention to follow all the steps previously mentioned in paragraph ‘’co-sleeping mode (Fixing
to the bed)’’.
DISASSEMBLING THE CRIB
The crib can be fully disassembled in order to store it in the bag supplied with the product. To disassemble the crib,
remove the crib from the frame then disassemble the frame.
Care & Maintenance
Do not iron
Do not dry clean
10