MyRepublic WI-FI HUB+ User manual

MyRepublic Pty Ltd ACN 603 909 815
Overview
This guide is here to provide some answers to some commonly asked questions about your Wi-Fi
Hub+.
Tip: you can connect to your Wi-Fi Hub+ using an Ethernet cable if you are experiencing issues
with your wireless connection. Plug the yellow Ethernet cable from your device to one of the yellow
LAN ports on your Wi-Fi Hub+.
Recovering your Wi-Fi Hub+ Modem wireless key (password)
If you have not changed your Wi-Fi password, you can find your SSID and Password on:
1. The magnetic Wi-Fi card that came with your modem
2. On the sticker underneath your modem
If you have changed the wireless settings manually and you do not remember your
password, try one of the following:
1. Use a computer that is already connected to your network
2. If none of your computers are connected to the wireless network, connect via the
Ethernet cable to one of your available Ethernet ports
3. Type 192.168.1.1 into your web browser
4. Enter the username and password (admin, admin), then select Sign in
WI-FI HUB+
TROUBLESHOOTING GUIDE

MyRepublic Pty Ltd ACN 603 909 815
5. Click on the wireless card. The wireless page appears.
6. On the left menu, select the access point that you want to view.
7. Under Access Point, you can find the network name (SSID) and wireless key
(password).
8. You can now update the Wi-Fi SSID and password
9. When you have finished, click save
10. A changes saved successfully (at the top of the page) notification indicates your
settings have been updated
Your Wi-Fi Hub+ Modem does not appear in the wireless devices list on your
computer or smartphone
1. Make sure the wireless capability on your computer or smart device is turned on
2. Make sure that the Wi-Fi Hub+ wireless interface is enabled (it is turned on by
default).

MyRepublic Pty Ltd ACN 603 909 815
a. You can use the Wi-Fi On/Off button (press and hold for 5 seconds) to
switch your Modems Wi-Fi capability on and off. This button is physically
located on the top of your Wi-Fi Hub+.
If none of the above works, please do the following (recommended to connect via Ethernet)
3. Enter 192.168.1.1 into your web browser
4. Enter the username and password (admin, admin), then select Sign in
5. Click on the Wireless Card. The Wireless page appears.
6. In the Wireless settings, make sure that the enabled switch is set to on
7. If the signal is low or not available, try to reposition the Wi-Fi Hub+ closer to your
wireless device
8. If none of the above options work, try changing the wireless channel (see below)

MyRepublic Pty Ltd ACN 603 909 815
The Wi-Fi Hub+ has “disappeared” from your wireless device list
If you could connect previously, but can’t connect anymore:
1. Make sure that the wireless device you are trying to connect to has its Wi-Fi signal
activated (for example, sometimes laptops have a physical switch on the device that
lets you turn its wireless capability on and off)
2. Make sure that the wireless client is still using the correct wireless settings (network
name (SSID), security settings)
Poor Wireless Connectivity or Range
1. If the signal is low or not available, try to reposition the Wi-Fi Hub+ closer to your
wireless device
2. Try changing the wireless channel (see below)
3. Use WPA(2)-PSK for your devices encryption
Change the wireless channel
1. Type 192.168.1.1 into your web browser
2. Enter the username and password (admin, admin), then select Sign in
3. Click Wireless. The Wireless page appears

MyRepublic Pty Ltd ACN 603 909 815
4. In the Channel list under Interface, click a channel other than displayed in Current
channel. Be sure to click Save so the channel settings take effect.
Cannot connect via WPS
The WPS button allows you to connect to another Wi-Fi device in range without the password.
To do so, press the WPS button which can be found on the side of the Wi-Fi Hub+ next to the USB
port and connect to your Wi-Fi device, please note, this only opens the Wi-Fi connection for 2
minutes.
If you have trouble connecting your wireless client via WPS, try one of the following:
1. Wait until the WPS LEDs of the Wi-Fi Hub+ and other devices are off and then try again
2. Move the devices closer to each other to ensure they are within wireless range
3. Make sure that WPS is enabled on the Wi-Fi Hub+:
a. Type 192.168.1.1 into your web browser
b. Enter the username and password (admin, admin), then select Sign in

MyRepublic Pty Ltd ACN 603 909 815
c. Click Wireless. The Wireless page appears
d. On the left menu, select the access point to which you want to connect using
WPS
e. Under Access Point, make sure that:
i. Broadcast SSID is switched to on
ii. WPS is switched to on
iii. Security mode is not WEP (only applicable when using a 2.4Ghz radio
mode)
iv. If you made changes, click Save.

MyRepublic Pty Ltd ACN 603 909 815
Customer Support Contact
8am-10pm 7 days a week
1300 130 888
[e-mail]
myrepublic.com.au/support