Myson Kickspace 500 User manual
KICKSPACE®500, 600 & 800
REMOTE CONTROL SWITCH.
SWITCH INSTALLATION INSTRUCTIONS
l This remote control switch is suitable for operating one
KICKSPACE®unit only.
l It is important that these instructions are read thoroughly
before proceeding with the installation.
l This kit must be installed by a qualified electrician.
l This accessory pack is designed to convert a MYSON
KICKSPACE®fan convector unit from integral switch
controls providing Off and two fan speeds to a remote
switching facility of the same sequence.
l This pack contains a three metre length of cord specially
terminated and colour coded for the application. No other
cord can be used to connect the remote control switch to
the fan convector unit.
Important: Isolate the electricity supply to the
KICKSPACE®fan convector. Do not reinstate the
supply until the installation has been completed in
accordance with these instructions.
1.0 Controls Switch
1. Locate a convenient wall space above the KICKSPACE®fan
convector that will permit connection via the three
metre cord supplied. The switch mounting point must be
away from sources of moisture and heat.
2. Fit a suitable switch mounting box for the type of installation.
Connect one end of the three metre cord to the remote
switch as shown in the Remote Control Unit diagram on
the back.
3. The cord must be installed in accordance with current
codes of practice. It should preferably be recessed, but
if exposed, it shall be protected by suitable conduit.
Run the cord via the prepared route to the KICKSPACE®
fan convector.
2.0 KICKSPACE®Unit
1. Remove the fixing screw(s) and lift the tabs holding the
electrical connection cover in place.
2. Locate the fan speed switch on the front control panel.
Disconnect the red and yellow wires that connect between
this switch. Discard these wires.
3. Remove the brown wire from the back of the fan speed
switch.
4. A cable clamp bush is supplied with the Remote Control
Kit. Route the cable through the hole in the side panel,
and make the following connections:
Yellow lead:
Connect to the low fan speed spade connector.
Red lead:
Connect to the high fan speed spade connector.
Brown lead:
Connect to the brown wire disconnected from the fan
speed switch.
Green/Yellow:
Connect to chassis earth tag.
Fit the cable clamp bush onto the cable ensuring that
internal wiring is not too tight, and that it does not contact
the copper heat exchanger pipe-work.
5. Refit the control cover onto the unit.
6. Reinstate the electrical supply to the KICKSPACE®fan
convector.
Motor Connections
Low Terminal (Yellow)
High Terminal
(Red)
Common
Terminal
(Blue)
Product Serial Number:
Please leave this manual with the end user.
Part Number: 1370062
27941 Kickspace remote installation A4 18/09/2014 11:16 Page 1
MOTOR
L
N
br
bl
g/y
bl yr
bl bl
g/y
br
Chassis Earth Chassis Earth
Low Limit
Summer/Winter
Thermostat
Switch
L1 L3 L2
L3 L2
L1
g/y
MOTOR
L
N
br
bl
g/y
bl yr
bl bl
br
Chassis Earth Chassis Earth
Low Limit
Summer/Winter
Thermostat
Switch
1122
CC
NOTE: The addition of the Remote Control Switch renders the integral fan speed control switch inoperative.
The Summer/Winter switch operation remains unchanged.
White Remote Switch
Metallic Remote Switch
After Sales Service
MYSON SERVICE, Unicorn Trading Park, Somerden Road, Hull, HU9 5PE, UK
Spare parts and technical help on all Convector products are available from MYSON SERVICE.
MYSON Eastern Avenue, Team Valley, Gateshead, Tyne & Wear NE11 0PG, UK
heatingthroughinnovation.
01.09.2014 ISSUE 2
27941 Kickspace remote installation A4 18/09/2014 11:16 Page 2
Other manuals for Kickspace 500
6
This manual suits for next models
2
