Mytee ECO-17 User manual

1
Instructions for
ECO-17 Orbital Encap / Floor Machine
13655 Stowe Dr. Poway, CA 92064
Model #
Serial #
Form # ADM-ECO17
5-16
Please read before use.
Register your product
at http://www.mytee.
com/support/register
General Information p. 2
Unboxing & Assembly p. 4
Set Up & Operation p. 5
Flywheel Bearing Replacement p. 9
Parts & Pricing p. 10
Notes p. 12

2
Dear Customer:
Congratulations on the purchase of your new ECO-17. As you are already aware,
the scene of the equipment world is becoming more high tech, and we at Mytee
Products Inc. strive to keep you on the cutting edge with superior quality and
technology.
Keep in mind that the ECO-17 is a machine, so neglect or abuse will cause un-
necessary damage and void the warranty. However with simple maintenance the
ECO-17 will give quality performance for many years to come.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com.
Before you begin using your new machine, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed in ac-
cordance with all local code and ordinances. Do not remove ground pin; if missing,
replace plug before use.
Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualied electrician or service person if you are
in doubt as to whether the outlet is properly grounded. Do not modify the plug
provided with the machine. If it will not t the outlet, have a proper outlet installed
by a qualied electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and acces-
sories. Call Mytee for repair parts or service. Please specify the Model and Serial
Number when discussing your machine.
Name Plate
The Model and Serial Number of your machine are shown on the Nameplate on the
handle of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping cartons and the
machine for damage. If damage is evident, save the shipping cartons so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le a
freight damage claim. NOTE: This machine ships in two boxes.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or
death.
Is used to call attention to a situation that could cause severe personal injury.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, ba-
sic precautions should always be followed, including the following: Read all instruc-
tions before using this machine. This product is intended for commercial use only.
To reduce the risk of re, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjust-
ments or repairs.
4. Use care to keep the electrical supply cord from contacting the rotating brush
or drive block.
5. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
6. Do not pull or carry by cord. Do not close a door on cord or pull cord around
sharp edges or corners.
7. Connect to properly grounded (3-wire) outlet only. Refer to grounding instruc-
tions.
8. Do not run appliance over cord. Keep cord away from heated surfaces.
9. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
10. Turn off all controls before unplugging.
11. Always unplug or disconnect the appliance from power supply when not in use.
12. Do not handle the plug or oor machine with wet hands.
13. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
14. Wind the cord no tighter than is necessary to retain it during storage.
15. Do not use in areas where ammable or combustible material may be present.
16. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
17. Use only the appropriate handles to move and lift unit. Do not use any other
parts of this machine for this purpose.
18. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.
19. Use extra care when working near stairs.
20. To reduce the risk of re or electric shock, do not use this machine with a
solid-state speed control device.
21. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
22. When cleaning and servicing the machine, local or national regulations may
apply to the safe disposal of liquids which may contain: chemicals, grease, oil,
acid, alkalines, or other dangerous liquids.
23. Store your oor machine indoors in a cool, dry area.
24. Keep your work area well lit.
25. Do not leave operating unattended.
Use of ammable chemicals could cause explosion, re, and death.
Figure 1
Grounding Pin
Grounded Outlet
Grounded Outlet Box
Adapter
Tab for Grounding
Screw
Metal
Screw
Figure 2 Figure 3
GENERAL INFORMATION

3
Pre-Operation
1. Vacuum carpet and upholstery and remove other debris.
2. Inspect power cord for damage.
Operation
1. Squeeze the Adjustment Height lever.
2. Pivot handle to desired position (best is at waist height).
3. Release lever to lock handle in place.
4. Place both hands rmly on the handle grips.
5. Flip the power switch to the “on” position.
6. To spray solution, squeeze either spray lever.
7. To stop the machine, simply ip the power switch to the “off” position.
Pad Driver Removal / Installation
1. Disconnect the power cord from the electrical outlet and empty any liquid in
the solution tank before installing a brush or pad driver.
2. Leave the handle in the upright position and tip the machine backwards so it
rests on its wheels and upper handle section.
3. Use an 11mm wrench to loosen and remove the four bolts from the bottom to
the pad driver.
4. To install the pad driver, place the pad driver into position and bolt into place
with the original four 11mm bolts.
5. Raise the machine back into upright position.
6. To install a cleaning pad, tip the machine back and lower it, with the pad driver
installed, onto the cleaning pad. Keep the pad as centered as possible.
7. When the machine is not in use, store it with the pad attached. This will protect
the pad driver from damage.
1. Work away from outlet and power cord to prevent cord damage.
2. To clean heavily soiled areas, repeat cleaning path from different direction.
Guidelines
1. For ease of operation, always keep the brush or pad surface level, balanced,
and at on the oor at all times.
2. Always adjust the operating handle to a comfortable height at which the brush
or pad surface is balanced before starting the machine.
3. Your oor machine will operate differently on various surfaces. There will be
more resistance when the machine is used with a brush on carpet than when it
is used with a pad on a smooth surface.
4. To move the machine forward or backward, push or pull in the desired direc-
tion, keeping the pad or brush level on the oor at all times.
After Use
1. Unplug the extension cord from wall and the machine’s power cord pigtail and
loosely wind it up.
2. After each use, wipe your oor machine with a clean, soft, damp cloth.
3. Store in a clean, dry place with a pad attached to protect the pad driver.
4. Do not expose to rain. Store indoors.
Maintenance Schedule
Maintenance item Daily Once a week
Clean and inspect motor
Check power supply cable
Clean machine with all purpose cleaner and cloth
Inspect machine for water leaks and loose hardware
x
x
x
x
Troubleshooting
There is no power.
1. Plug machine in proper outlet.
2. Ensure that switch is not damaged or defective.
Plug on the power cord doesn’t light up when plugged in.
1. Replace the power cord.
Plug lights up when plugged in but machine does not turn on.
1. Open the faceplate on the handle and check for loose or disconnected wires.
2. Power switch may be bad. Replace the power switch.
Motor is drawing too many amps and blowing breakers.
1. Power cord is defective or damaged - replace power cord.
2. Check the power switch for shorts or loose connections. Replace the switch if
necessary.
3. Check if the power cord from the switch is defective or damaged. Replace if
necessary.
Machine Specications
Motor 1 horsepower
Cleaning Path 17”
Pump Diaphragm spray pump
Pump PSI 100
Pump GPM 1.3
Solution Tank 4 gallons
Levers Stainless steel
Deck Plate Stainless steel
Amp Draw 13 amps
Power Cord 50’ 12/3 extension cord
FAQs
Q: How much does the ECO-17 weigh and what are the dimensions?
A: Machine weight is 130 lbs. Dimensions are 27” x 17.5” x 49” (L x W x H).
Q: What comes standard with the ECO-17?
A: The ECO-17 comes with:
• 17” pad driver (pre-installed)
• 19” cleaning pad
• 50’ extension cord (12/3)
Q: Does Mytee recommend a pad for the machine?
A: Yes, pads will vary depending on the surface you are cleaning.
Q: Where do I plug the machine in?
A: The ECO-17 requires a grounded circuit. Please note: GFI outlets may trip
before the breaker setting.
Q: Is there anything I can do to increase the expected life of my machine?
A: Check all parts for wear regularly. Keep machine clean.
GENERAL INFORMATION

4
ECO-17 ENCAP MACHINE UNPACKING & ASSEMBLY
Tools Needed:
• 5/16” allen hex key
• Needle nose pliers
The ECO-17 ships in two boxes and will need to be
assembled before use. Follow these directions to
assemble the two pieces.
2. Remove both C-clips from the axle using needle nose
pliers. Slide the wheels onto the axle. Use needle nose
pliers to secure wheels with the C-clips.
3. Connect the hoses for solution spray and gravity feed
as shown above.
5. Make sure all bolts are tightened. Your ECO-17 is now
ready to operate.
4. Connect the power cord from the base of the handle to
the motor.
1. Set the handle assembly in place and bolt it in using
the two included bolts. Thread the bolts in by hand as
far as you can in order to prevent stripping of the
threads in the handle. Tighten with 5/16” allen key.

5
BACK
FRONT
1. Power Switch
2. Handle Height
Adjustment Lever
3. Power Cord Pigtail
4. Solution Tank
5. Bi-Directional Valve
6. Pump
7. Motor
8. Spray Jets
9. Solution Spray Levers
10. Handlebars
11. Faucet Fill Hose
12. Solution Tank Drain Cap
13. Wheels
14. Solution Tank Lid
3
1
2
4
5
6
7
8
14
9
10
11
12
13
ECO-17 ENCAP MACHINE SETUP & OPERATION
SHAMPOO TANKHEIGHT ADJUSTMENT LEVER
The handle can be adjusted to any desired working posi-
tion by simply squeezing the adjustment lever. Move the
handle to the desired position, then release the adjust-
ment lever, locking the handle in place.
To ll the shampoo tank, twist off the large cap and ll
with water from a bucket or ll using the faucet ll hose.
Add desired shampoo or chemical. To drain, lower the
handle a bit, place a bucket under the drain cap, and
unscrew the cap.

6
The ECO-17 features a valve that allows you to switch
between using the pump to spray solution or using the
gravity-feed hose. Point the valve knob to the left for grav-
ity feed and to the right to use the spray jets.
Note: Disconnect the power cord from electrical outlet
and empty any solution from the tank before removing or
installing the pad driver. The pad driver is attached with
four bolts (highlighted above). To use a pad, simply lay
the pad on the oor and lower the machine with the pad
driver onto the pad. Try to center the pad as much as
possible.
PAD DRIVER AND PAD INSTALLATION BI-DIRECTIONAL VALVE
ECO-17 ENCAP MACHINE SETUP & OPERATION
SOLUTION SPRAY LEVER
Squeeze the left or right solution spray levers to activate
the pump and spray solution.
POWER SWITCH
To turn the machine on, lower the handle to the desired
position and then ip the power switch to the “on” posi-
tion.

7
ECO-17 ENCAP MACHINE SETUP & OPERATION
To effectively clean oors, move the ECO-17 forwards and backwards, similar to using a household vacuum
cleaner. Wet the oor by spraying solution as you roll the ECO-17 forwards.
ECO-17 CLEANING PATTERN

8
ECO-17 ENCAP MACHINE SETUP & OPERATION
USING THE ECO-17 ON VARIOUS SURFACES
CARPET
TILE & GROUT
EPOXY
VINYL
STONE
WOOD
CONCRETE
& MORE
IMPORTANT: Ensure that you are using the appropriate pad type
depending on the surface you are cleaning.

9
ECO-17 FLYWHEEL BEARING REPLACEMENT
1. Remove the pad driver assembly by removing the 4 hex
bolts with an 11mm wrench.
2. Keep the motor shaft in place on the top of the motor us-
ing a athead screwdriver. Loosen the jam nut with a 15/16”
open-ended wrench. Remove the ywheel assembly by
turning it counter-clockwise.
3. Unscrew the two allen bolts from the back of the y-
wheel plate and remove the bearing assembly.
4. Install the new bearing assembly. Align the bolt holes
and replace the two allen bolts. Use Loctite to ensure bolts
are secure.
5. Thread the jam nut all the way down on the shaft and
hold it with the 15/16” open-ended wrench. Install the
ywheel assembly with the new bearing assembly by
threading it onto the shaft clockwise until it stops on the
jam nut. Tighten the jam nut against the ywheel plate.
The ywheel should spin freely.
6. Re-install the pad driver assembly using the same four
hex bolts and 11mm wrench.
Tools Needed:
• 11mm wrench
• 15/16” open-ended wrench
• 3/16” allen wrench
• Flathead screwdriver
CLICK HERE for a quick video on removing the
ywheel plate.

10
ECO-17 ENCAP MACHINE PARTS & PRICING
ITEMS NOT SHOWN
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
H151
bolt, 5/16-18 x 3/4" Long SHCS
4 $0.99 ea
2
H421
washer, 5/16" lock, s/s
4 $0.99 ea
3
H843
locking arc, handle adj, floor machine
1 $51.99 ea
4
H555
plate, yoke, EC-17
1 $33.99 ea
5
H216
nut, lock, 1/4-20, nylon insert, s/s
4 $0.99 ea
6
H210
washer, 1/4" flat, s/s
19 $0.99 ea
7
H316
bolt, 1/4-20 x 1-1/2" hex head, s/s
6 $0.99 ea
8
H065
bushing, sleeve, 5/8 i.d. x 1.25" long
2 $9.99 ea
9
H066
bolt, shoulder 5/8" x 1.25", 1/2-13 thrds 2 $14.99 ea
10
H427
washer, wave
2 $1.49 ea
11
H212
flat washer, 9/16"ID x 1 1/16"OD, AN960-C916
6 $0.99 ea
12
H109
wheel, 10", foam filled
2 $79.99 ea
13
H042
c-clip, 12mm, external
2 $0.99 ea
14
H228
axle, 13.10" x .50" dia
1 $9.99 ea
15
H553
arm, left
1 $98.99 ea
16
P607
bushing, flange, .63" i.d. x .38" long
4 $0.99 ea
17
H554
bracket, arm, EC-17
2 $28.99 ea
18
P606
bushing, flange, .63" i.d. x .25" long
4 $0.99 ea
19
H242
bolt, shoulder, 5/8" x 1.5", 1/2-13 threads 2 $19.99 ea
20
H252
bolt, shoulder, 1/4" x 1.5", 10-24 threads
4 $3.99 ea
21
H351 screw, 1/4-20 x 3/4", socket head, s/s
4 $0.99 ea
22
H213
washer, 1/4" lock, s/s
11 $0.99 ea
23
C326B
motor, ECO-17
1 $548.99 ea
24
B140
connector, 1/4" push-in x 1/8" mpt
6 $7.49 ea
25
H559
plate, ECO-17
1 $329.99 ea
26
G123
BUMPER, ECO-17
1 $29.99 ea
27
H327
washer, 3/8" lock, s/s
4 $0.99 ea
28
H293
bolt, 3/8-16 x 1", hex head
4 $0.99 ea
29
H558
weight, counter, EC-17
1 $43.99 ea
30
H556
bearing, offset, EC-17
1 $30.99 ea
31
H342
bolt, 1/4-20 x 1" hex head, s/s 3 $0.99 ea
32
P608 adapter, pad driver, encap machine
1 $23.99 ea
33
G113A
PAD DRIVER, ECO-17
1 $98.99 ea
34
H201
bolt, 1/4-20 x 1/2" hex head, zinc
4 $0.99 ea
35
H398
nut, hex, 5/8-18
1 $1.99 ea
36
H202
bolt, 1/4-20 x 3/4" hex head, s/s
4 $0.99 ea
37
H485
handle, aluminim grip, black
1 $6.99 ea
38
B645A
filter, cap, ECO-17
2 $4.99 ea
39
B645C
jet, ECO-17
2 $9.99 ea
40
B645D
filter, strainer, ECO-17
2 $8.99 ea
41
B645B
filter, body, ECO-17
2 $5.99 ea
42
H384
washer, 3/8 flat, s/s
4 $0.99 ea
43
H560
L bracket, ECO-17
2 $3.99 ea
44
H561
jet bracket, ECO-17
2 $3.99 ea
45
H922
screw, thumb, 1/4-20 x 1/2"
2 $4.99 ea
46
G052
washer, buna 1-1/8" od x 3/16" id
2 $1.99 ea
47
B153
coupling, 1/8" npt, light pattern
2 $5.49 ea
48
PH657-11
tubing, 1/4", nylon, blk
2
$1.99 ft
49
H403
nut, lock, 10-24, nylon insert
4 $0.99 ea
50
H322
nut, hex, 1/2-13, s/s
2 $0.99 ea
51
H552
arm, right
1 $98.99 ea
52
H231
screw, 10-32 x 1" phil pan head, s/s
5 $0.99 ea
53
B110
adapter, brass, 1/4" sw barb x 1/4" fpt, w/gasket
1 $3.99 ea
54
PH634-8 sol hose, 1/4", silicone braided, clear
1
$6.49 ft
55
H349
heat sink, demand pump
1 $24.99 ea
56
B147
tee, 1/8" fpt x 1/8" fpt x 1/8" fpt
1 $6.49 ea
57
B657
elbow, 45 deg street, 1/8" mpt x 1/8" fpt
2 $4.99 ea
58
B129
nipple, hex, 1/8" mpt x 1/8" mpt
2 $1.99 ea
59
B656C
valve, ball, 1/8" fpt x 1/8" fpt, s/s
1 $10.99 ea
60
PH657-15
tubing, 1/4", nylon, blk
1
$1.99 ft
61
PH634-12 sol hose, 1/4", silicone braided, clear
1
$6.49 ft
62
B170
ferrule, 1/4" brass
4 $0.99 ea
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
63
B136
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
2 $4.99 ea
64
B105
bushing, brass, 3/8"mpt x 1/4" 2 $3.19 ea
65
C305A
pump, 100 PSI, no pressure switch
1 $136.99 ea
66
H397
bracket, pump mount, ECO-17
1 $25.99 ea
67
B131
fitting, 1/4" barb x 1/8" FPT
1 $2.99 ea
68
H164
grommet, 5/8" ID
4 $1.99 ea
69
B195
barb, 3/8" barb x 1/8" mpt
1 $2.49 ea
70
B143
street elbow, 90 degrees, 1/8"
2 $2.99 ea
71
B261
valve assy 3 way
1 $54.99 ea
72
PH715-25 sol hose, 3/8", silicone braided, clear
1
$7.99 ft
73
B241
adapter, brass, 3/8" barb x 1/4"mpt
2 $1.99 ea
74
H299
washer, 11/16"id x 1-1/2"od x .075, s/s
1 $0.99 ea
75
B663A
insert, knurled, 10/32 short
1 $1.99 ea
76
A507
valve, shampoo tank & handle rod
1 $24.99 ea
77
H915
clamp, shampoo tank
2 $4.99 ea
78
P559
tank, ST-4
1 $39.99 ea
79
PH612-60
clear tubing, 1/2" OD x 3/8" ID, faucet fill
1
$1.99/ft
80
G031
gasket, 3.25" i.d. x 5.88" o.d.
1 $6.99 ea
81
P560
cap, 6", threaded
1 $23.99 ea
82
G055
tether, cap, 6 1/2"
1 $12.99 ea
83
H612
Washer, #8, flat regular
2 $0.99 ea
84
H230
screw, 10-32 x 1/2" phil pan head, s/s 4 $0.99 ea
85
H178
faucet fill
1 $10.99 ea
86
H223
cable, 15.5" long, 10-32 thrd x swivel ring
1 $9.49 ea
87
P573
tube, nylon support - 3/8"
1 $2.99 ea
88
H002
spring, shampoo tank cable
1 $5.99 ea
89
H149
bolt, 5/16" shldr x 5/8" w/ 1/4-20 thrd
2 $0.99 ea
90
H148
washer, 5/16", narrow
4 $0.99 ea
91
P529
spacer, lever, handle adj.
2 $1.99 ea
92
H215
nut, hex, 1/4-20 s/s
2 $0.99 ea
93
H357
thumb screw, 1/4" - 20, shampoo tank
2 $1.99 ea
94
G036
cap, 2.5" threaded, tethered
1 $3.49 ea
95
H341
handle pivot, floor machine
1 $74.99 ea
96
H705
bolt, giude, locking piston
1 $0.99 ea
97
H847
bushing, locking piston
1 $17.99 ea
98
H152
retaining ring, internal 1 1/2"
1 $0.99 ea
99
H157
spring, handle adjustment
1 $5.99 ea
100
H844
locking piston, handle adj.
1 $19.99 ea
101
H273
nut, kep, #10-32 zinc
2 $0.99 ea
102
H916
clip, cord, 5/16", nylon- BLACK
1 $0.99 ea
103
H159
cable, handle adj, floor machine
1 $6.99 ea
104
H839
lever, handle adj., floor machine
1 $19.99 ea
105
H216
nut, lock, 1/4-20, nylon insert, s/s
1 $0.99 ea
106
E384
power cord, end, 15.5", 14/3
1 $11.99 ea
107
H144
strain relief, power cord, metal
1 $12.99 ea
108
H167
switch, floor machine
1 $13.99 ea
109
H640
washer, internal star, 3/8" zinc
1 $0.99 ea
110
H384
washer, 3/8 flat, s/s
2 $0.99 ea
111
H166
insulation, switch, floor machine
1 $3.99 ea
112
H855
lever, switch, floor machine
1 $6.99 ea
113
H160
spring, switch/lever
2 $0.99 ea
114
E515
switch, rocker, 2 position
1 $13.99 ea
115
H255
switch cover, EC, floor machine
1 $30.99 ea
116
P967A
plug, switch
2 $1.99 ea
117
G040
grip, handle, floor machine
2 $1.99 ea
118
P524
plug, plastic, floor machine handle
1 $0.99 ea
119
H849
handle, floor machine
1 $89.99 ea
PART NO.
DESCRIPTION
QTY
MSRP
E530
power cord, ext, blue lit, 50', 12/3
1 $88.99 ea
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
ECO-17
SHEET 1 OF 3
Encap
3/2015
OD
SCALE: 1:24
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
M.LaBarbera

11
ECO-17 ENCAP MACHINE PARTS & PRICING
1
2
3
4
5
7
8
9
10
11 12
13
14
15
16 17
18
19
6
20
21
22
24
23
25
26
27
28
29
30
6
33
34
36
22 37
43
22
36
44
45
46
47
24
48 6
49
50
18
16
51
1
2
89
90
91
92
88
86
87
93
77
78
94
7
90
76
75
73
74
77
55
60
24
56
65 52
79
73
85
80
81
82
83
84
103
89
90
104
105 91 106 107
108
109
110
110
111
112
113
114
115
84
117
52
92
119
95
96
97
98
99
100
68
101
102
101
84
6
11
57
58
59
31
22
6
11
32
67
66
53
68
6970
71 58 24
72
42
41
39
38
40
24
64
63
62
54
61
35
116
118
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
ECO-17
SHEET 2 OF 3
Encap
SCALE: 1:24
REV
DWG. NO.
D
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
mytee
PRODUCTS, INC.
858-679-1191
M. LaBarbera
3/2015
OD
DO NOT SCALE DRAWING

12
Mytee Products Inc.
13655 Stowe Dr.
Poway, CA 92064
www.mytee.com
© 2016 Mytee Products Inc.
Printed in the U.S.A.
NOTES