Mytee Breeze BZ-102LX User manual

Breeze Model:
BZ-102LX, BZ-102-LXH, BZ-102LX-AUTO,
BZ-103LX, BZ-105LX, BZ-105LX-AUTO
User Manual
13655 Stowe Dr. Poway, CA 92064
P: [phone]
F: [phone]
www.mytee.com
REV. 6/16/20
™
Please read and understand this manual completely
before operating this machine.

2
Introduction
Dear Customer:
Congratulations on the purchase of your new Breeze™ Carpet Extractor. As
technology continues to develop you can work condently knowing that both
Mytee Products and its employees are equally dedicated to developing with the
industry and its advances.
Like any other piece of machinery or technology, the Breeze™ also requires
proper maintenance and care to keep the product working over extended use.
Neglecting your machine, abusing it or not operating it properly can void its
warranty and prevent the machine from performing to the quality and standard
you’d expect out of the Mytee Products line.
If you have any warranty concerns or questions, please review this manual
thoroughly or do not hesitate to contact your distributor. If there are questions
regarding maintenance, replacement, or ordering parts please contact an
authorized Mytee Products Service Center. To see an updated list please visit
our website at https://www.mytee.com/support/nd-distributors/.
Before using your Mytee product, please read this manual thoroughly.
Sincerely,
Mytee Customer Care Dept.

3
Table of Contents
1
2
3
4
Important Safety Information 4
At a Glance 6
1.1 - Technical Specications 6
1.2 - Included with the Breeze™ 7
1.3 - Breeze™ Front View 7
1.4 - Breeze™ Rear View 8
Machine Operation 9
2.1 - Powering the Breeze™ 9
2.2 - Connecting Hoses 9
2.3 - Filling the Solution Tank 9
2.4 - Switching On the Breeze™ Components 9
2.5 - Chemical Injection (BZ-105LX-AUTO Only) 10
2.6 - Auto-Fill and Pump-Out (AUTO Units Only) 10
2.7 - After Use 10
Machine Maintenance 11
3.1 - Opening the Unit for Maintenance 11
3.2 - System Maintainer 11
Troubleshooting 12
4.1 - Vacuum Troubleshooting 12
4.2 - Pump Troubleshooting 12
4.3 - Heater Troubleshooting 13

4
Important Safety Information
Grounding Instructions
This machine must be grounded. If it should malfunction or
break down, grounding provides a path of least resistance
for electrical shock. This machine is equipped with a cord
having an equipment-grounding conductor and grounding
plug. The plug must be plugged into an appropriate outlet
that is properly installed in accordance with all local code
and ordinances. Do not remove ground pin; if missing,
replace plug before use.
Improper installation of the equipment-grounding
conductor can result in a risk of electric shock. Be sure to
check with a qualied electrician or service person if you
are in doubt as to whether the outlet is properly grounded.
If the plug will not t in the outlet do not modify the plug or
the machine’s cord, instead have a proper outlet installed
by a qualied technician.
This machine is for use on a nominal 120-volt circuit and
with a grounding plug similar to the one in Figure 1 below.
If a proper outlet is not available, follow the illustrations of
Figure 2 & 3 to install a temporary-grounding plug. This
temporary work-around should be used only until a proper
outlet (Figure 1) can be installed by a qualied electrician.
When and if this type of adapter is employed, screw the
adapter’s extended tab into place with a metal screw.
However, grounding adapters are not approved for use in
Canada.
Again, be sure to check the grounding pin for damages
and replace if necessary.
The Green, or Green-Yellow, wire in the cord is the
grounding wire. When replacing a plug, this wire must be
attached to only the grounding pin.
DO NOT use extension cords.
Please Note for America use only.
Parts and Service
Please contact Mytee service personnel or a Mytee au-
thorized Service Center using Mytee original replacement
parts and accessories if repairs need to be performed.
When and if calling Mytee for support, please have your
Model and Serial Number available for faster assistance.
Name Plate
The Model and Serial Number are located on the lower half
of the back of the machine near the power plug and will be
required for ordering replacement parts. You can use the
space provided in this manual to note down both for future
referencing.
Unpacking the Machine
When your new machine is delivered, please carefully
inspect both the shipping carton and the machine for
damages. If damage is evident, save both the shipping
carton and machine so that the delivering carrier can
inspect it. Contact the carrier immediately to le a freight
claim if there has been any damage.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potential-
ly dangerous conditions. Always read this information
carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause
severe personal injury or death.
Is used to call attention to a situation that could cause
severe personal injury.
Is used to call attention to a situation that could cause
minor personal injury or damage to the machine or other
property. When using an electrical appliance, basic
precautions should always be followed, including the
following: Read all instructions before using this machine.
This product is intended for commercial use only.
To reduce the risk of re, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manu-
facturer’s recommended attachments.
Figure 1
Grounding Pin
Grounded Outlet
Grounded Outlet Box
Adapter
Tab for Grounding
Screw
Metal
Screw
Figure 2 Figure 3

5
Important Safety Information
3. Always unplug power cord from electrical outlet before
attempting any adjustments or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on
cord or pull cord around sharp edges or corners.
6. Do not run appliance over cord. Keep cord away from
heated surfaces.
7. Do not use with damaged cord or plug. If cord is
damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and/or standing
water.
9. Always unplug or disconnect the appliance from power
supply when not in use.
10. Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
11. Do not use in areas where ammable or combustible
material may be present.
12. Do not leave the unit exposed to harsh weather
elements. Temperatures below freezing may damage com-
ponents and void warranty.
13. Use only the appropriate handles to move and lift
unit. Do not use any other parts of this machine for this
purpose.
14. Keep hair, loose clothing, ngers, and all parts of the
body away from all openings and moving parts.
15. Use extra care when using on stairs.
16. To reduce the risk of re or electric shock, do not use
this machine with a solid-state speed control device.
17. The voltage and frequency indicated on the name plate
must correspond to the wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or
national regulations may apply to the safe disposal of
liquids which may contain: chemicals, grease, oil, acid,
alkalines, or other dangerous liquids.
19. Do not leave operating unattended.

6
1 - At a Glance
1.1 - Technical Specications
BZ-102LX
Solution Tank 10 gallons
Recovery
Tank
10 gallons
Vacuum
Motors
Dual exclusive Mytee®
LX™ vacuum motors
225-250 CFM, 182” water
lift
Solution Pump 220 PSI
Wheels Front: 4” locking casters
Rear: 10” wheels
Amp Draw Cord One: 15 amps
Cord Two: 14 amps
Amp Draw,
230V 50Hz
Model BZ-102LX-230
Cord One: 8 amps
Cord Two: 7 amps
Net Weight 108 lbs.
Machine
Dimensions
20” x 29” x 37”
BZ-103LX
Solution Tank 10 gallons
Recovery
Tank
10 gallons
Vacuum
Motors
Dual exclusive Mytee®
LX™ vacuum motors
225-250 CFM, 182” water
lift
Solution Pump 220 PSI
Heater 600 watt REAL HEAT™
system
Wheels Front: 4” locking casters
Rear: 10” wheels
Amp Draw Cord One: 17 amps
Cord Two: 18 amps
Amp Draw,
230V 50Hz
Model BZ-103LX-230
Cord One: 8 amps
Cord Two: 9 amps
Net Weight 112 lbs.
Machine
Dimensions
20” x 29” x 37”
BZ-102LXH
Solution Tank 10 gallons
Recovery
Tank
10 gallons
Vacuum
Motors
Dual exclusive Mytee®
LX™ vacuum motors
225-250 CFM, 182” water
lift
Solution Pump 220 PSI
Heater 1,600 watt REAL HEAT™
system
Wheels Front: 4” locking casters
Rear: 10” wheels
Amp Draw Cord One: 15 amps
Cord Two: 15 amps
Amp Draw,
230V 50Hz
Model BZ-102LXH-230
Cord One: 8 amps
Cord Two: 8 amps
Net Weight 112 lbs.
Machine
Dimensions
20” x 29” x 37”
BZ-105LX
Solution Tank 10 gallons
Recovery
Tank
10 gallons
Vacuum
Motors
Dual exclusive Mytee®
LX™ vacuum motors
225-250 CFM, 182” water
lift
Solution Pump 500 PSI
Wheels Front: 4” locking casters
Rear: 10” wheels
Amp Draw Cord One: 20 amps
Cord Two: 16 amps
Amp Draw,
230V 50Hz
Model BZ-105LX-230
Cord One: 10 amps
Cord Two: 8 amps
Net Weight 109 lbs.
Machine
Dimensions
20” x 29” x 37”
BZ-102LX-AUTO
Solution Tank 10 gallons
Recovery
Tank
10 gallons
Vacuum
Motors
Dual exclusive Mytee®
LX™ vacuum motors
225-250 CFM, 182” water
lift
Solution Pump 220 PSI
Automation • Auto-ll
• 3.3 GPM pump-out
Wheels Front: 4” locking casters
Rear: 10” wheels
Amp Draw Cord One: 16 amps
Cord Two: 18 amps
Amp Draw,
230V 50Hz
Model
BZ-102LX-AUTO-230
Cord One: 8 amps
Cord Two: 9 amps
Net Weight 113 lbs.
Machine
Dimensions
20” x 29” x 37”
BZ-105LX-AUTO
Solution Tank 10 gallons
Recovery
Tank
10 gallons
Vacuum
Motors
Dual exclusive Mytee®
LX™ vacuum motors
225-250 CFM, 182” water
lift
Solution Pump 500 PSI
Automation • Auto-ll
• Chemical injection w/ 5
gallon chemical bottle
• 3.3 GPM pump-out
Wheels Front: 4” locking casters
Rear: 10” wheels
Amp Draw Cord One: 20 amps
Cord Two: 16 amps
Amp Draw,
230V 50Hz
Model
BZ-105LX-AUTO-230
Cord One: 10 amps
Cord Two: 8 amps
Net Weight 113 lbs.
Machine
Dimensions
20” x 29” x 37”

7
1 - At a Glance
1. Clear recovery tank lid
2. Front lift handle
3. 10 gallon recovery tank
4. Recovery tank drain valve
5. Pressure gauge (where applicable)
6. Pump-out connection tting (where
applicable)
7. Auto ll connection (where
applicable)
8. 4” front locking casters
9. Prime valve (500 PSI models)
10. Pressure regulator (500 PSI
models)
11. Solution hose connection
12. Vacuum hose Cu-Lynx™
connection
1.3 - Breeze™ Front View
1.2 - Included with
the Breeze™
1
2
3
4
7
5
6
8
9
11
12
10
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
H110V
SHEET 1 OF 1
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:1
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
H141V
SHEET 1 OF 1
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:1
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
H141V 2” x 1.5” Cu-Lynx™
Reducer
2x 50’ Twist-Lock Power Cords
H110V 2” x 2” Cu-Lynx™ Coupler
G008 Pack of 25 Piglet™ Filters

8
1 - At a Glance
1. Rear push handle
2. Loading Buddy wheel attachment
3. Twist lock power cord sockets
4. 10” rear wheels
5. Switch plate
1.4 - Breeze™ Rear View
1
2
3
4 5

9
2 - Machine Operation
2.1 - Powering the
Breeze™
Connect power cords by
lining up the female end
of the cord with the male
prongs in the socket on the
machine. Twist clockwise to
lock the cord in place.
Each power cord on the Breeze™ requires a grounded 20
amp outlet. For dual cord machines, plug each cord into
its own 20 amp circuit. The dual circuit indicator light and
tone will activate when this is achieved. ♦
2.2 - Connecting
Hoses
Use the included Cu-Lynx™
hose connectors to connect
1.5” or 2” vacuum hose to
the Breeze™. Connect the
solution hose via the quick
connect tting on the front
of the Breeze™ as shown
here. ♦
2.3 - Filling the Solution Tank
The Breeze™ solution tank can be lled up from a bucket
via the opening under the solution tank lid. ♦
2.4 - Switching On the Breeze™ Components
Units Without Heater (BZ-102LX, BZ-102LX-AUTO,
BZ-105LX, BZ-105LX-AUTO)
After a cleaning tool is connected and the solution tank is
lled, switch on the vacuums and the pump in any order.
Units With Heater (BZ-102LXH, BZ-103LX)
In order to avoid vapor locking the unit, the components
should be switched on by following the procedure below
after a cleaning tool is connected:
1. Turn pump switch on. Pull the lever on the cleaning tool
to release air in the line. Hold lever until a steady ow of
water comes out of the wand.
2. Once pump is primed and there is pressure in the
solution line, turn on heater switch and wait a few minutes
for water to heat up.
3. Once water is heated, turn on vacuum and begin
cleaning.
BZ-102LXH Variable
Switch
The variable switch on the
BZ-102LXH model allows
you to switch between the
heater and VACUUM 2.
Follow the same procedure
shown above when heater
will be used. ♦
VAC 1 PUMP VAC 2
HEATER
VAC 1 VAC 2 PUMP HEATER
3 1 2

10
2 - Machine Operation
2.5 - Chemical Injection (BZ-105LX-AUTO
Only)
Fill the included 5 qt. bottle with chemical concentrate of
your choice. With a cleaning tool connected, switch on
the pump and pull the trigger on your tool to keep water
owing. Turn the chemical injection knob counter-clock-
wise to open the valve. This allows chemical to siphon
into the line. Turn the knob until you see the bubble reach
the desired gallons per hour of chemical. Follow chemical
manufacturer’s instructions for correct ratio.
IMPORTANT: If chemical injection will not be used, make
sure the chemical injector is closed by turning the knob all
the way clockwise. ♦
2.6 - Auto-Fill and Pump-Out (AUTO Units
Only)
Auto-ll: Connect standard
garden hose from water
source to the auto-ll
connection on the front of
the unit. Turn on the water
source and let the tank
begin to ll. It will shut
o when the water level
reaches the oat switch in
the solution tank.
Pump-out: Connect a
second standard garden
hose to the pump-out
connection and lay the
other end of the hose in a
draintable location. Activate
the pump-out switch on the
front of the machine and
open the ball valve on the
pump-out connection. The
Breeze™ will automatically drain recovered water from the
tank. ♦
2.7 - After Use
Emptying the recovery
tank: Place a bucket or
other appropriate recepta-
cle under the recovery tank
drain valve and pull up on
the drain valve lever to drain
dirty water.
Emptying the solution
tank: Connect a vacuum
hose to the Breeze™ and
turn on at least one of the
vacuums. Open the solution
tank lid and vacuum out
any left-over solution in the
tank. Once the solution tank
is empty, drain the recovery
tank by following the above
instructions. ♦

11
3 - Machine Maintenance
In order to keep the Breeze™ running smoothly and
reduce the risk of damage to the machine and subsequent
downtime, Mytee recommends following the maintenance
schedule below:
Maintenance Item Daily Weekly
Clean and inspect tanks. X
Clean and inspect hoses. X
Check and clean internal lters. X
Check power supply cables. X
Clean machine with all-purpose
cleaner and cloth. X
Flush solution system with Mytee
System Maintainer. X
Run clean water through the
chemical injection system
(BZ-105LX-AUTO only).
X
Inspect vacuum hoses for holes and
loose cus. X
Inspect machine for water leaks and
loose hardware. X
3.1 - Opening the Unit for Maintenance
To open the Breeze™, loosen the latches on the front of the
unit by turning them one quarter turn counter-clockwise.
Flip the latches down and then lift up on the handle and the
machine will open up. ♦
3.2 - System Maintainer
Weekly ushing of the solution system with Mytee®
System Maintainer helps keep lines clean and prevents
chemical build-up, improving pump life, performance and
pressure.
How to use System Maintainer:
1. Mix 1-quart 3601 System Maintainer with 1-quart of
warm water.
2. After thoroughly mixing, pour this solution into the
solution tank.
3. Turn the pump on FIRST, and run solution through your
cleaning tool. NOTE: The jet should be removed from the
cleaning tool in order to prevent clogging due to loosening
of deposits in line.
4. Next, turn on the heater (if equipped). If the heater is
turned on rst, it will result in a vapor lock, which will aect
the machine’s operation.
5. Next, with both the pump and heater on, begin running
the solution through the machine. This allows the solution
to break down any build up in the lines.
6. After running all of the solution through the machine, ll
the tank with clean, warm water. Run the water through the
machine to clear the solution completely out of the tank &
lines. ♦

12
4 - Troubleshooting
4.1 - Vacuum Troubleshooting
Vacuum is not turning on.
Possible Cause Solution
Vacuum may not be getting
power.
Check for faulty connec-
tions between the motor,
switch, relay and power
cord. Secure any loose
connections.
Vacuum is not producing suction.
Possible Causes Solutions
Recovery tank is full. Empty the recovery tank.
External vacuum hose
blockage (if there is no
exhaust).
Check for blockage in
the hose, starting from
the cleaning tool to the
machine.
Clogged lter in vacuum
tank.
Clean out lter regularly.
Drain valve/cap is loose
and is causing air leakage.
Tighten the drain cap/make
sure valve is completely
shut.
Hose cus are loose and
causing air leakage.
Tighten all hose cus
regularly as may loosen
over time. Use a glue to
prevent cus from coming
loose (optional).
Lid on vacuum tank is loose
and is causing air leakage.
Make sure the lid is tight.
Vacuum blows water out the exhaust.
Possible Causes Solutions
Electronic shuto is mal-
functioning, causing the
vacuum to continue running
even when the recovery
tank is full.
Replace the electronic oat
switch with a ball oat.
Foam building up in the
recovery tank.
Use a defoamer.
Boot behind vacuum port is
turned the wrong way.
Make sure this plastic boot
is turned toward the right
wall of the machine and not
toward the ball oat.
There is a loud grinding noise coming from the
vacuum.
Possible Cause Solution
Debris has been sucked
into the vacuum motor
chamber. Usually results
from dry vacuuming.
Replace the vacuum motor.
To avoid repeat problem,
DO NOT dry vacuum with
your extractor.
4.2 - Pump Troubleshooting
Pump runs but there is no spray.
Possible Causes Solutions
Tank is empty. Fill tank.
Blockage or kink
somewhere in the line.
Locate where the blockage
is and repair accordingly.
Pump valves are clogged or
damaged.
Examine valves and clean
or replace.
Pump has lost prime. Follow the priming
procedure.
Low pressure.
Possible Causes Solutions
Nozzle is worn Replace nozzle with a new
one of the same size.
Leak in high pressure hose
or connections.
Check hose or connec-
tions, replace as needed.
Filter is clogged. Clean lter.
Pump valves are clogged or
damaged.
Examine valves and clean
or replace.
Pump pulsates when spraying.
Possible Causes Solutions
Filter is clogged. Clean lter.
Pump valves are clogged or
damaged.
Examine valves and clean
or replace.
Motor does not operate.
Possible Causes Solutions
Blown circuit breaker. Replace circuit breaker.
Check circuit for wire
damage or component
damage.
Leaks seen under pump.
Possible Causes Solutions
Pump seals are worn. Replace with new plunger
and seals.

13
4 - Troubleshooting
4.3 - Heater Troubleshooting
Heater is not heating water.
Possible Causes Solutions
Loose electrical
connection.
Check all electrical connec-
tions, including power cord
and harness.
Automatic sensor has
failed, causing manual
sensor to trip.
Reset the manual sensor
button by pressing the
small white and yellow
button in the center of the
sensor. If this works, but
heater continues to trip
the manual sensor, replace
the automatic sensor (Part
#E573) on the heater.
Heater element has failed. Check for continuity
through the element by
reading the amperage. If
amps are low, only part of
the element may be heating
up – in this case, the
element is damaged and
needs to be replaced.
Bad power switch. If the element, sensors, and
wiring all check out okay,
there may be a bad switch
on the switch-plate.
Running out of hot water too fast.
Possible Causes Solutions
Too much water owing
through the heater.
Remember, when using
your machine, it is rec-
ommended you do one
wet pass followed by two
dry passes. This way you
are not spraying as much
and the hot water will last
longer.
Jets being used are too
large.
If your machine has a
1,000W or 1,200W heating
system, make sure your
cleaning tool has 0.02 jets.
Water in tank is very cold. If possible, ll your solution
tank with warm water
in order to shorten the
amount of time it takes for
the water to heat up. The
pumps are usually rated for
140°F water.
Heater has hard water
buildup inside, leading to
lost eciency.
Run Mytee System
Maintainer™ (Part # 3601)
through the machine
regularly in order to clear
hard water or chemical
residue that can block
water ow and reduce
heating ability. See product
label for instructions.
Unit has vapor locked and there is no water pumping
out of the unit.
Possible Cause Solution
Turning on the heater
before turning on the pump
and priming the unit.
Turn o the heater and
allow the unit to cool com-
pletely. When machine has
cooled, turn on the pump
rst. Prime the unit by
spraying solution out of the
cleaning tool. Then, turn on
the heater.

Mytee Products, Inc.
13655 Stowe Dr.
Poway, CA 92064
www.mytee.com
© 2020 Mytee Products, Inc.
Printed in the USA
NOTES