NAD CI 16-60 User manual

© NAD CI 16-60
®CI 16-60 Multi-Channel Amplier
Quick Setup Guide
GUIDELINE FOR NETWORK SETUP CONNECTION
This guideline is applicable to PC, MAC or smartphone control devices. Adapt the guidelines according to your
control device.
1 Use an Ethernet cable (not supplied) to connect CI 16-60’s LAN port to your Wired network or router.
IMPORTANT NOTES
• For wired connection to be established, ensure that a broadband router that supports Ethernet is setup and
available.
• Ensure that CI 16-60 and the control device (PC, Mac or smartphone device) are connected to the same network.
• Use the information in the rear panel MAC ID sticker to identify the CI 16-60 from your network.
2 Power up your CI 16-60. The CI 16-60 will not communicate with the network when in Eco standby mode.
3 Use any network IP scanner to nd your CI 16-60’s Network ID (listed as the product name (NAD CI 16-60)
immediately followed by the last six digits in the MAC (Machine Access Control) address
(example: NAD CI16-60_123456). Note also the corresponding IP address assigned by the network.
4 Type the IP address into your control device’s web browser to access your CI 16-60’s User Interface (UI).
5 Congure your CI 16-60’s Identication, Input/Output and Settings parameters via User Interface.
FIRMWARE UPGRADE PROCEDURE
1 Upon gaining access to your CI 16-60’s User Interface, check immediately for any rmware update by selecting
“Check For Updates”from the “Settings”tab.
2 Follow the rmware upgrade prompt instructions to complete the upgrade process.
POWER OPTIONS
SETTING DESCRIPTION
Power button Press power button to set unit to operating or standby mode.
Always On Unit is always in operating mode. Shut down power by disconnecting unit’s AC plug from the mains power
source.
12V Trigger Presence or absence of +12V DC supply from compatible devices to rear panel +12VTRIGGER IN will remotely
switch the unit to operating or standby mode.
Signal Sense Unit will instantaneously turn from standby to operating mode if it senses any input signal (approximately
above 2 mV RMS input) applied through any of the GLOBAL or LINE INPUT sockets.
IMPORTANT
CI 16-60 factory default setting for Eco Mode is ON. With “Power Mode” set to “Signal Sense” and “Eco Mode” set
to “ON”, CI 16-60 will automatically go to Eco standby mode after 20 minutes of no active audio source input.
nadelectronics.com/product/ci-16-60-multi-channel-amplier
support.nadelectronics.com
AUDIO OUT
LR
© NAD CI 16-60
1.
© NAD CI 16-60
x1
© NAD CI 16-60
2 CHANNEL AUDIO OUT
UNBALANCED
RBALANCED LBALANCED
L
R
x1/x2/x3...x8
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
MODEM USBLAN 4
LAN 3LAN 2LAN 1
DISPLAY USB USB
x8 x1 x1 x4 x4

©2020 NAD ELECTRONICS INTERNATIONAL, A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.
No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
CI16-60-QS-EN-v04 - 06/20
4.
3.
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
2.
x1/x2/x3......x16
+ -- +
STEREO
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
x1/x2/x3...x8
- +
BRIDGE
STANDBY AND CHANNEL LED STATUS INDICATORS
DESCRIPTION STANDBY LED STATUS CHANNEL LED 1-16 STATUS
Operating mode Blue If there is a signal, corresponding channel
LED is solid blue or no light if no signal.
Standby mode Amber O, no light
System reboot Amber Red $Blue $ O $no light
Overvoltage or under voltage Red O, no light
AMP current error Blue Corresponding channel LED is red.
AMP DC error Red O, no light.
POWER CONSUMPTION AND HEAT OUTPUT
CONDITION
230 V/50 HZ 120 V/60 HZ
POWER
CONSUMPTION (W)
HEAT OUTPUT
(BTU/HR)
POWER
CONSUMPTION (W)
HEAT OUTPUT
(BTU/HR)
Eco Mode Standby Power at 8 ohms 0.44 1.50 0.42 1.43
Network Standby Power at 8 ohms 1.20 4.10 1.12 3.82
Idle power at 8 ohms 47 160 49 167
Output power at 8
ohms, all channels
driven
1/8 rated power 154 526 157 536
1/3 rated power 334 1140 342 1167
1/2 rated power 483 1648 498 1700
Full rated power 930 3174 982 3352
Output power at 4
ohms, all channels
driven
1/8 rated power 185 631 188 642
1/3 rated power 417 1423 433 1478
1/2 rated power 601 2051 629 2147
Full rated power 1169 3990 1261 4304
IMPORTANT
Visit nadelectronics.com/product/ci-16-60-multi-channel-amplier or support.nadelectronics.com for further information and assistance.
12