NADAMOO Bur3069 User manual

Bur3069 Wireless Barcode
Scanner User Manual
V53.02

In order to correctly use the bar code scanner, please read the instruction carefully and
do not arbitrarily scan the settings code otherwise some settings may not be available
temporarily.
Please keep this instruction for reference in the future.
If you have any question or concern about the operation of the scanner, please contact
us at following Email:
[email protected] / [email protected] / [email protected]
You are suggested to write down the model & the specific scenario and consult the
maintenance person should you find the scanner abnormal.

1
Contents
Technical Parameter
2
Packing list
3
Battery & Charging
3
Set Up Step
4
FAQs
6
Troubleshooting
8
Optional Function settings
9
1. Pairing Mode Setting
9
2. Upload Mode Setting
13
3. Scanning Mode Setting
15
4. End Character Setting
18
5. Add Character
18
6. Delete Character
23
7. Barcode Enable Setting
25
8. Barcode Type ID Setting
26
9. UPC/ EAN Setting
27
10. Code 39 Setting
29
11. Codabar Setting
30
12. Auto power off
31
13. Language setting
32
14. .Voice setting
33

2
Technical Parameter
Mfr P/N
Bur3069
Radio Frequency
433MHz Wireless
Wireless Range
Indoor 100m, outdoor 400m
Memory
10000 barcodes
Battery capacity
500mAh Polymer Battery
Charging Input voltage
DC 5V ± 0.25 V
Power
100 mW (work); 400 mW (maximum instantaneous)
Current
20 mA (work)；100 mA (maximum instantaneous)
Standby current:
<20uA
Printing Contract
30% minimum reflectance difference
Light source
Visible 650nm laser diode
Temperature
0 ℃ to 50 ℃ (work); -40 ℃ to 60 ℃ (storage)
Resolution
4 mil
Depth of Field
5mm-630mm
CPU
ARM 32-bit Cortex
Bit Error rate
1/5000000
Decoding speed
280 times/sec
Scanning angle
rotor angel±20°，inclination± 45°，declination ± 60°
Drop test
2.0m
Certificate
CE，FCC，RoHS ，IP54
Applicable 1D barcode
UPC / EAN , UPC / EAN with Supplementals, , Code 39,
MSI, Code11, Code 39 Full ASCII, Code 128, Code 128Full
ASCII, Codabar, Code93 , Codabar, Chinese2of5,
Inteleaved 2 / 5, Interleaved 2 of 5

3
Packing List
Barcode scanner *1
Cradle *1 (As charging base and barcode receiver)
USB cable *1
User manual *1
Battery & Charging
The scanner is powered by rechargeable polymer battery.
Please ensure that the scanner has enough power before use.
Battery level indication:
(1) Turnning the scanner on, when the buzzer beeps and the blue indicator light is on
all the time , it indicates that the battery is sufficient
(2) Turnning the scanner on, when the buzzer beeps, the red indicator light is on
or the red indicator light flash three time and then cut down automatically. Please stop
scanning and charge the scanner.
Insert one end of USB cable into the cradle, and insert another end to computer USB
interface or 5V DC USB interface power, put the scanner on the cradle, it will start
charging.
Charging indicator：
The light on scanner will turn red during charging, when the scanner is full charged, the
light will turn blue
NOTE:
1. Please use computer USB interface or special 5V DC power adapter for charging, the
abnormal power will cause permanent damage to scanner and battery

4
Set Up Step
(The scanner has been paired with the cradle, and set up already. )
Step 1: Plug one end of the cable into the computer usb port, plug another end into
the Cradle. The blue indicator light on the cradle will turn on, after 5 second it will start
flashing. Lift up the antenna.
Step 2: Start the scanner by pressing the key (The blue light on scanner will flash and
the buzzer will beep. If the scanner has no response, please put the scanner to cradle
for charing , the light on scanner will turn red when charging, when the scanner is full
charged, the light will turn blue)
Step 3: Test the scanner using EXCEL , click on any cell and scan a barcode to see if the
barcode comes up on cell.
If the barcode comes up on EXCEL, it means that the scanner works.
If the barcode does not come up on cell, please set up the scanner again according
the following reset steps:
Step 1. Scan the code "enter into settings" "restore factory setting" "exit setting"
orderly to restore the scanner

5
Step 2. Unplug the cradle , scan code "one to one" , the scanner will go to pairing
mode and beep continuously, then plug the cradle to USB port, if the scanner has one
"beep"sound in 3s , that means the pairing is succeed
Note: if the pairing fails, please unplug the cradle and repeat step 2.
Step 3. Scan code "normal mode" to set it to instantly upload barcode
FAQ
Q1: If i scan a product barcode, will it include the name of the product in the file
automatically?
Answer：
The computer works like a keyboard. The scanner does not interpret what the barcode
is, it just "types" out a string of alphabet numeric characters that the barcode
represents.
it's up to the database software you are using to interpret what that string of characters
means. Once you acquire the barcodes, you have to correlate them to something more

6
meaningful by either purchasing a software service that will interpret the barcode and
relate it to a product, or you can use your own internal inventory system to assign the
barcodes to specific products.
After creating the relationship between your barcode and the corresponded
information ,when you enter the barcode into the software by the scanner,your
software will look up the barcode and then output the related information of your
product.
Q2: Why can the scanner not read the barcodes?
Answer：
There are some reason for that.
Maybe the scanner failed to match the cradle.
Maybe the scanner was set to check mode . In check mode, the data will store in the
built in storage of scanner).
Please follow the set up steps on page 4 to set up the scanner again.
The other possible reason is that the setting is off by default, for some barcode types
are not commonly used. You need to activate a specific barcode type to get it to work .
Or maybe this is a bar code with extra check digit.
Please send us a clear picture of the barcode , our customer service will help you to
solve the problem.
Q3: Why does scanner not read the barcode exactly. When I use the scanner to read a
barcode of an item, I get a different result from the barcode itself.

7
E.g 1. When I use the scanner to read a UPCE barcode “08960007” , scanning result
is 8960007. The leading digit is missing.
Solution: The scanner was set to not read the leading digit of UPCE barcode by default.
If you want to set the scanner to read the leading digits of UPCE , please read the
following code ordrly "enter into settings">" show UPCE leading digit">"exit settings"
(On Page 28 )
E.g 2. There are two separate barcodes together. It scanned the first 12 digits in the
barcode but not the last five.
Solution: The scanner was set to not read the extra code by default.
If you want to set the scanner to read the five extra code of UPCA, please scan the code
"enter into settings">" Read extra 5 digits of UPCA">"exit settings"(on page 28）
E.g 3. The original barcode is“abc12345”，the scanning result is “+A+B+C+D12348”，
the scanner put “+” between character.
Solution: The scanner was set to not read the Code 39 Full ASCll code by default.
If you want to set the scanner to read Code 39 Full ASCll code，please scan the code
"enter into settings">“Read Code39 FULL ASCII“ >"exit settings“ (on page 29)
If that is not your case, please send us a clear picture of the barcode and the result you
get, our customer service will help you to solve the problem.
Q4.Is there any barcodes to remove auto-enter after every scanning?
Answer:
To remove the auto-enter, please read the code”Cancel Enter”on page 18.

8
Troubleshooting
Problem
Possible Reason
Solution
Insert the usb cradle into
the PC ‘ s usb port, the
cradle ’ s light does not
light up
The PC’s usb port is out of
condition
Connect the usb receiver
to another USB port
The cradle or the usb
cable is out of condition
Contact us for the
replacement.
Power on the scanner,
the scanner has no
reaction. The buzzer
does not beep, the light
on the top of scanner
does not turn on, the red
scanning laser does not
show up
The battery run out
Connect the scanner to
PC’s usb port for charging
via usb cable
The scanner can not hold
the charge
The PC’s usb port is out of
condition
Connect the scanner to
another usb port for
charging
The cradle or usb cable is
out of condition
Contact us for the
replacement
Power on the scanner,
the buzzer beeps, the
light on the top of
scanner will be on, the
red scanning laser does
not show up or become a
dot
The laser head is out of
condition
Contact us for the
replacement
Scanner and usb receiver
are all in good condition.
But the barcode can not
be sent to my computer
The scanner failed to
match the usb cradle
Please follow reset set
steps on page 4-5 to set
up the scanner again
The scanner was set to
check mode，scanned data
will be kept in the buffer of
scanner

9
Optional Function settings
Settings of the barcode scanner can be changed by scanning the setup barcodes
included in this manual.
1. Pair Mode Settings
The scanner has three paring mode:
1.1 .One scanner to one cradle:One barode scanner send barcode to one cradle
Pairing operation:
Scan the "One to One" barcode, the scanner will go into pairing mode and beeps
continuously. Then insert the cradle to USB port, if the scanner has one "beep" in 3s
that means the pairing is succeed.
Note: 5 second after the cradle is inserted, the cradle's blue light will be flicking, that
indicated that the cradle can not be paired. So If the pairing fails, you need to pull off
the usb receiver and re-set as the previous steps.

10
Several units can work independently with different computers in the same area. They
won't interface with each other during work.
If you want to use them on multiple computers, each with own scanner and receiver.
Please follow the setps
1) Scan the code “one to one”using scanner A , and then plug the cradle A to
computer’s usb port.
2) After the blue light of cradle A is flicking or unplug the cradle A, scan the code
“one to one”using scanner B , and then plug the cradle B to another computer’s usb
port

11
1.2. One scanner to many cradle: One barcode scanner send barcode to a
number of cradle
Pairing operation：
1) Scan the "One to More" barcode using scanner A, the scanner will go into pairing
mode and beeps continuously. Then insert the cradle A into USB port, if the scanner
has one "beep"in 3s that means the pairing is succeed.
2) Then plug the second cradle B into USB port to connect it to the scanner A.
....
One scanner can be connected to maximum 8 cradle.
if you have added to the required number of receiver, press the trigger to end the
adding.
Note: The more cradle you add, the longer time it takes to upload the barcode.

12
1.3.More scanner to one cradle:A number of barcode scanner send barcode
to one receiverPairing operation:
Pairing operation：
1) Scan the "More to One" barcode using scanner A, the scanner A will go into pairing
mode and beeps continuously,
Then insert the cradle A to USB port, if the scanner has one "beep" in 3s that means the
pairing is succeed, meanwhile the light of receiver will flicker.
2) Unplug the cradle A, scan the "More to One" barcode using scanner B, the scanner A
will go into pairing mode and beeps continuously,
Then insert the cradle A again to USB port, if the scanner has one "beep" in 3s that
means the pairing is succeed, meanwhile the light of receiver will flicker.
.....
Note: The more scanner you add, the longer it takes to wait for the bar code to be
uploaded.

13
2. Upload mode setting
The scanner has three upload mode:
2.1. Normal mode:
Scanning barcode and real-time upload the barcode.If the barcode is upload
successfully, the blue LED light will flicker once, at the same time buzzer will beep.
Scan the code "Normal Mode" to set the scanner to normal mode
Under the normal mode,the transmission distance is over 400m where there are no
obstacles. If it exceeds the transmission distance or the data upload failed, the scanner
will let out 3 short prompt.
2.2.Non-losing Mode:
The barcode will be uploaded to the receiver in real-time when the scanner is in
wireless tranmission range. When the scanner is out of the wireless tranmission range,
the data will be stored in scanner’s own memory .
After scanner is reaching the wireless transmission range,the lost data which are stored
will be uploaded to the computer automatically.
Scan the code " Non-losing Mode" to set the scanner to Non-losing Mode
Scan the code "Clear Non-losing Mode Stored Data" to clear all the Non-losing Mode
stored data
Note: "Non-losing mode" is not suitable for using in the the "Fliker Scanning mode"
and " Continuous mode"
3.3. Check mode
The data will be stored in scanner’s own memory. And then you could upload the data

14
in batchs to your conputer when you need them.
Scan the code " Check mode" to set the scanner to check mode,
Scan the code " Total checking number " to show the quantity of stored barcode
Scan the code " Upload checking data" to upload all the stored data
Scan one of the time interval to select speed transmission of check mode
Scan the code "Clear checking data" to clear all the checking mode stored data

15
3. Scanning Mode Setting
The scanner has three scanning mode:
3.1.Manual Trigger mode (default) : Press the trigger to read the bar code,
please read the following codes orderly to set the scanner to Manual trigger mode .
"enter into setting">"Manual trigger "> "exit settings"
3.2.Flicker scanning mode: read the bar code at a certain frequency
please read the following codes orderly to set the scanner to Flicker scanning mode.
"enter into setting">"Flicker scanning"> "exit settings"
Attention：
The flicker scanning time interval can be set through reading the "Parameter barcode"
in 0-9
Flicker time unit is 500ms and can set to 01-15 grade.
For example,if you want to set the flicker time interval out to be 1000ms,
please read the following codes orderly :
"enter into setting">"Flicker Scanning Time"> Paremeter code "0""2">"exit settings"
3.3.Continuous scanning mode：The laser is always on, the scanner read code without
pressing the trigger.
please read the following codes orderly to set the scanner to continuous scanning
mode:
"enter into setting">"continuous scanning"> "exit settings"
Attention 1：
The continuous scanning time interval can be set through reading the Parameter
barcode in 0-9.
Reading interval time unit is 500ms ,and can set to 01-15grade.

16
For example,if you want to set the reading time interval out to be 1000ms,please read
the following codes orderly:
"Enter into setting">"Scanning interval Time"> Paremeter code "0""2">"exit settings"
Attention 2：
In continuous scanning mode, it is allow to continuously read the same barcode via
setting the time interval of reading same barcode.
The time interval unit of reading same barcode is 0.1s,the time interval can be set
between 0-12 second.
If the time interval is set to 12.7 second,it means that it is not allow to read the same
barcode.
The numberical must have three numbers, if it has less three numbers please fill "0" in
first digit.
For example, if you want to set the the time interval of reading same barcode out be
2s,please scan
the following code orderly:
"Enter into setting">"Scanning the same barcode interval Time"> Paremeter code
"0""2" "0">"exit settings"

17
Paremeter code：

18
4. End Character Setting
To add terminator TAB , scan following codes orderly:
"enter into settings">"TAB">"exit settings"
To cancel terminator TAB , scan following codes orderly to restore the scanner to
default setting.
"enter into settings" >"restore factory setting" >"exit setting"
The scanner add “ Enter ” key by default.
To cancel terminator Enter, scan following codes orderly
"enter into settings" >"cancel enter" >"exit setting"
5. Add Character
To add prefix
For example： Add prefix XY
Please scan the following code orderly:
"enter into settings">"Add prefix">parameter code"5""8""5""9">"save">"exit settings"