Nalu Kai Naish Kite 810 complete User manual

HYDROFOIL SYSTEM
USER MANUAL

2 3naishfoils.com
TABLE OF CONTENTS RELEASES & AGREEMENTS
RELEASE AND WAIVER OF CLAIMS AGREEMENT
In consideration of your use of this product, you hereby agree to the following, to the fullest extent
permitted by law:
To waive any and all claims that you have or may have in the future against Naish International, a
division of Nalu Kai Incorporated, or any of its agents, resulting from use of this product and any of
its components.
To release Naish International, a division of Nalu Kai Incorporated, or any of its agents from any and
all liability for any loss, damage, injury or expense that you or any users of this product may suffer,
or that your next of kin may suffer, as a result of the use of this product, due to any cause whatsoever,
including negligence or breach of contract on the part of Naish International, a division of Nalu Kai
Incorporated, or any of its agents, in the design or manufacture of this product.
ARBITRATION
In further consideration of the sale to you of this product and any of its components, you hereby agree
to submit to binding arbitration any and all claims, which you believe you may have against Naish
International, a division of Nalu Kai Incorporated, or any of its agents, arising from the use of any of
the Naish International/Nalu Kai Incorporated equipment. The arbitration shall be pursuant to the
rules of the American Arbitration Association.
Arbitration shall be commenced within one (1) year from the date on which any alleged claim rst
arose. Further, the arbitration shall be held in Maui, Hawaii unless otherwise mutually agreed to by all
parties. The submission to the American Arbitration Association shall be limited and the arbitration
award may be enforced by any court of competent jurisdiction.
BINDING EFFECT OF AGREEMENT
In the event of your death or incapacity, this Agreement shall be effective and binding upon your heirs,
next of kin, executors, administrators, assigns and representatives.
ENTIRE AGREEMENT
In entering into this Agreement, you are not relying upon any oral or written representations other
than what is set forth in this agreement and User’s Guide.
ASSUMPTION OF RISK
Use of this product and any of its components involves certain inherent risks, dangers and hazards,
which can result in serious personal injury and death. In using this product you freely agree to assume
and accept any and all known and unknown risks of injury while using this equipment. The risks
inherent in the sport can be greatly reduced by abiding by the Warnings and Safety Precautions listed
herein and by using common sense.
RELEASE OF LIABILITY, CLAIM WAIVER AND ASSUMPTION OF RISK AGREEMENT
RELEASE AGREEMENT .........................................................................................................3
INSTRUCTIONS
Assembled Foil System.....................................................................................................4
Required Tools & Hardware ............................................................................................5
Assembly Instructions......................................................................................................6
Assembly Diagram ............................................................................................................7
Abracadabra Plate............................................................................................................8
Abracadabra Positioning Tips......................................................................................... 9
WARNING & SAFETY PRECAUTIONS .............................................................................. 10
WARRANTY POLICY & MAINTENANCE...........................................................................11
RELEASES & AGREEMENTSTABLE OF CONTENTS

4 5naishfoils.com
ASSEMBLED FOIL SYSTEM
ASSEMBLY TOOL
REQUIRED HARDWARE
Torx T30 Screw Driver
(4) M6 Stainless Steel
T-nuts
(4) M6 25 mm
Stainless Steel Torx Screws
Attach the Base to the Board Using:
(3) M6 Torx 30 mm
Titanium Mast Screws
(3) M6 Torx 30 mm
Stainless Steel Mast Screws
Attach the Base to the Mast Using:
(4) M6 30 mm
Stainless Steel Torx Screws
Attach the Mast to the Fuselage Using:
(3) M6 Torx 20 mm
Titanium Wing Screws
(2) M6 Torx 20 mm Titanium Screws
Attach the Front Wing to the Fuselage Using:
Attach the Adjustable Stabilizer Foil (rear wing)
to the Fuselage Using:
ASSEMBLED FOIL SYSTEM REQUIRED TOOLS & HARDWARE
REQUIRED TOOLS & HARDWARE
Abracadabra Plate Standard Plate
Shown: Naish Foil Complete–Abracadabra

6 7naishfoils.com
ASSEMBLY INSTRUCTIONS ASSEMBLY DIAGRAM
The Naish Foil System utilizes M6 bolts throughout. Remember that foils are utilized in a very corrosive
marine environment; here are four important tips to maximize the life of your foil:
It is easiest if you assemble your new foil for the rst time in the order below:
A) ATTACH THE STABILIZER (REAR WING): With the fuselage right side up, foil mast slot upwards,
position the stabilizer on the at top surface of the fuselage with the wingtips upwards (you can also
use the countersink on the screw holes to determine the correct orientation). Tighten until nice and
snug using the Torx T30 screw driver.
B) ATTACH THE FRONT WING: Turn the fuselage so it is bottom up, position the front wing (with logo
down) to the scarf joint. Thread the M6 20 mm titanium center screw until hand-tight. Do the same
with the other two screws.
C) ATTACH THE PLATE TO THE MAST: Using the (3) M6 30 mm titanium Torx screws, tighten beginning
with the center screw rst, then the front and nally the back screw.
D) ATTACH THE MAST/PLATE ASSEMBLY TO THE FUSELAGE: Insert the mast into the fuselage, then
thread (3) M6 30 mm stainless steel Torx screws until hand-tight. As before, the nal tightening order
is center screw rst, followed by front screw and then back screw.
FIND MORE INFORMATION AND ALL AVAILABLE PARTS ON NAISHFOILS.COM.
1) Whenever possible, apply anti-seizing compound to the screw threads before assembling.
2) Always use the Torx head screw driver to avoid damaging the screw slots.
3) Disassemble and rinse with fresh water after each use.
4) Greasy ngerprints, especially coated in sunscreen, can affect the performance of your
foil mast. Clean it with pumice hand cleaner or a similar product for best performance.
A
B
D
C
STABILIZER
(REAR WING)
FUSELAGE
PLATE
MAST
FRONT WING
Scarf Joint
(3) M6 30 mm Titanium
Torx Mast Screws
(2) M6 20 mm Titanium
Torx Stabilizer Screws
(3) M6 30 mm
Stainless Steel
Torx Mast Screws
(3) M6 20 mm Titanium
Torx Front Wing Screws
Attaching Abracadabra or
Standard Plate to the Board
Naish Plate Options
ASSEMBLY INSTRUCTIONS ASSEMBLY DIAGRAM
Abracadabra Plate:
(4) M6 30 mm Stainless Steel Torx Screws,
(4) M6 Stainless Steel T-nuts
Standard Plate:
(4) M6 25 mm Stainless Steel Torx Screws,
(4) M6 Stainless Steel T-nuts
Abracadabra Plate
Standard Plate
Tuttle Mount
Deep Tuttle Mount
Shown: Naish Foil Complete–Abracadabra
M6 T-nuts
Torx Screws
ABRACADABRA

8 9naishfoils.com
ABRACADABRA PLATE
The Abracadabra plate system allows the baseplate conguration to be mounted to the board and
taken off and on with one simple hand screw.
Moving the Abracadabra system towards the nose of the board will increase lift in relation to the
stance position on the board
Moving the Abracadabra system towards the tail of the board will decrease lift in relation to the
stance position on the board
ASSEMBLY:
A) Screw the Abracadabra horseshoe and baseplate to the board in the desired position using the (4)
M6 30 mm stainless steel Torx screws and the (4) T-nuts.
B) Slide the Abracadabra mastmount into the horeshoe and tighten the set screw rmly by hand.
ATTENTION: The set screw can also be tightened with the Torx T30 screw driver. For longer masts
(75 cm and longer), always use the Torx T30 screw driver to tighten the set screw.
ABRACADABRA POSITIONING TIPS
A
B
M6 30 mm Stainles Steel
Torx Screw + T-nut
SET SCREW
HEAD-ON VIEW OF UNDERSIDE OF BOARD WITH ABRACADABRA BOARDMOUNT,
SHOWING NO MAST ATTACHED.
HORSESHOE
BASEPLATE
MASTMOUNT
MAST
ABRACADABRA PLATE ABRACADABRA POSITIONING TIPS
TRACKS

10 11naishfoils.com
WARNING & SAFETY PRECAUTIONS WARRANTY POLICY
WARNING & SAFETY
HYDROFOILING IN ANY WATER SPORT CAN BE DANGEROUS AND UNPREDICTABLE IN CHANGING
CONDITIONS. THE USER OF THIS PRODUCT SHOULD UNDERSTAND THAT PARTICIPATING IN ANY
FOILING ACTIVITY COULD CAUSE INJURY OR DEATH TO YOU AND/OR OTHERS AROUND YOU.
OBSERVE THE FOLLOWING SAFETY STANDARDS
WHENEVER USING THIS PRODUCT:
• Foiling is a dangerous sport.
• Always use extreme caution when using this product.
• Misuse of this product can cause serious injury or death.
• Never use this product unless you are in good physical health.
• Never use this product unless you are an experienced swimmer.
• Never act in a careless manner when using this product.
• We do not recommend hydrofoiling in breaking surf. Use extreme caution if you do.
• You are responsible for your own safety and the safety of others around you when
using this product.
• If you are under the age of 18, you must have your parents or legal guardian read these warnings
and instructions.
• If you are under 18 years of the age, you must not use this product without proper guidance and
supervision by your parents or legal guardian.
• Use of this product exposes the user to unexpected and unavoidable risks, dangers and hazards.
• Do not use this product if you are under the inuence of alcohol, drugs or medications.
• Never use this product in thunderstorm and/or lightning conditions.
• Never use this product in conditions that are above your ability level.
• Make sure you take lessons before using this product on the water.
• Always observe local rules and regulations when using this product.
• Always be aware of your surroundings including any people, watercrafts and obstacles above and
below the water.
• Steer clear of crowded line-ups and densely populated waters.
• Be aware of water depth and how deep your foil extends.
• Avoid shallow reef and other areas in which your foil may come into contact with other objects.
READ THE FOLLOWING POINTS BEFORE ASSEMBLING YOUR FOIL:
Naish warrants this product to be free from major defects—in material or workmanship—to the
original purchaser for a period of one year from the date of purchase.
This warranty is subject to the following limitations:
The warranty is valid only when the product is registered in the warranty section of naishfoils.com
within seven (7) days from the date of purchase.
The warranty is valid only when this product is used for normal recreational activities and does not
cover products used in rental or teaching operations.
Naish will make the nal warranty determination, which may require inspection and/or photos of the
equipment, which clearly show the defect(s). If necessary, this information must be sent to the Naish
distributor in your country–postage prepaid. Product may be returned only if a return authorization
number (RAN) is given in advance by the Naish distributor. The RAN number must be clearly labeled
on the outside of the package or it will be refused.
If a product is deemed to be defective by Naish, the warranty covers the repair or replacement of the
defective product only. Naish will not be responsible for any costs, losses or damages incurred as a
result of loss of use of this product.
This warranty does not cover damage caused by misuse, abuse, neglect or normal wear and tear
including, but not limited to: punctures, rigging with other than Naish components, damage due to
excessive sun exposure, damage caused by improper handling and storage, damage caused by
use in waves or shore break, or damage caused by anything other than defects in material
and workmanship.
This warranty is void if any unauthorized repair, change or modication has been made to any part
of the equipment.
The warranty for any repaired or replaced equipment is good from the date of the original
purchase only.
The original purchase receipt must accompany all warranty claims. The name of the retailer and
date of purchase must be clear and legible.
There are no warranties which extend beyond the warranty specied herein.
WARNING & SAFETY PRECAUTIONS WARRANTY POLICY & MAINTENANCE
MAINTENANCE REMINDER:
The Naish Foil System utilizes M6 bolts throughout. Remember that foils are utilized in a very corrosive
marine environment; here are four important tips to maximize the life of your foil:
1) Whenever possible, apply anti-seizing compound to the screw threads before assembling.
2) Always use the Torx head screw driver to avoid damaging the screw slots.
3) Disassemble and rinse with fresh water after each use.
4) Greasy ngerprints, especially coated in sunscreen, can affect the performance of your
foil mast. Clean it with pumice hand cleaner or a similar product for best performance.

naishfoils.com
© 2019 Naish International, a division of Nalu Kai Incorporated