NANLITE WC-USBC-C1 User manual

Guangdong NanGuang Photo&Video Systems Co., Ltd
USER MANUAL
WC-USBC-C1

1
Product Diagram
WC-USBC-C1 Wire Controller
WC-USBC-C1 wire controller is compatible with PavoBulb 10C and PavoTube T8-7X.
MODE button SWITCH button
+ - buttton
USB Type-C port
Hand strap hole
USB Type-C connector
Power switch
Display

2
Usage
1. Connect the wire controller to the fixture, then toggle the power switch to turn on the wire controller,
the "NANLITE" logo will be displayed on start up.
MODE SWITCHMODE SWITCH

3
2. When the wire controller is connected to the fixture, the wire controller will first read the information of the fixture,
including the address and fixture model.
①When the wire controller is not connected to the fixture, the display will show "Disconnected" (As shown in figure 1);
②When the wire controller is connected to the fixture, the screen will display the corresponding lighting mode
interface or menu of the fixture. (As shown in figure 2)
3. MODE button: For switching lighting modes and menu.
Note: (1) When the wire controller is connected to PavoBulb 10C, the lighting mode options including CCT,
HSI and EFFECT.
(1) When the wire controller is connected to PavoTubeT8-7X, the lighting mode options including CCT, HSI,
EFFECT, PIXEL FX.
Battery levelMode CCT
CCT: 5600K C/M: 0
DIM: 100%
CCT
CCT: 5600K C/M: 0
DIM: 100%
CCT
HUE: 000 SAT: 100
DIM: 100%
Disconnected
figure 1 figure 2
MODE SWITCH

4
CCT
HUE: 000 SAT: 100
DIM: 100%
CCT
HUE: 000 SAT: 100
DIM: 100%
CCT
HUE: 000 SAT: 100
DIM: 100%
CCT
HUE: 001 SAT: 100
DIM: 100%
figure 3
4. SWITCH button: For switching corresponding options under different light modes, or to switch the channel,
language, DMX mode, DMX pixel (only for PavoTube T8-7X), wireless protocol (only for PavoBulb 10C),
Bluetooth reset, firmware update and version under the menu options.
5. + - button: For adjusting the value of the corresponding options under the lighting mode. (As shown in figure 3)
MODE SWITCH
MODE SWITCH

5
6. Press MODE button to enter the menu.
①Channel (address code) setting
Press SWITCH button to CH.
MODE SWITCH
MODE SWITCH
MENU
LANGUAGE: ENG
CH: 512
MENU
LANGUAGE: ENG
CH: 512
MENU
LANGUAGE: ENG
CH: 512

6
②Language setting
Press SWITCH button to LANGUAGE.
Press + - button to adjust the value of the address code.
MODE SWITCH
MODE SWITCH
MENU
LANGUAGE: ENG
CH: 512
MENU
LANGUAGE: ENG
CH: 511
MENU
LANGUAGE: ENG
CH: 512
MENU
LANGUAGE: ENG
CH: 512

7
Press + - button to select Chinese or English.
③DMX mode setting
Press SWITCH button to DMX MODE.
MENU
CH: 512
LANGUAGE: ENG
MENU
CH: 512
LANGUAGE: ENG
菜单
通道：512
语言：中文
MODE SWITCH
MODE SWITCH
MENU
DMX PIEXL: 01
DMX MODE: CCT 8bit

8
Press + - button to select the desired DMX mode.
④DMX PIXEL setting (Note: Only controllable with PavoTube T8-7X.)
Press SWITCH button to DMX PIXEL.
MODE SWITCH
MODE SWITCH
MENU
DMX PIEXL: 01
DMX MODE: CCT 8bit
MENU
DMX MODE: CCT 16bit
DMX PIEXL: 01
MENU
DMX MODE: CCT 16bit
DMX PIEXL: 01
MENU
DMX MODE: CCT 16bit
DMX PIEXL: 01

9
Press + - button to adjust the number of DMX pixels.
⑤Wireless protocol setting (Note: Only controllable with PavoBulb 10C.)
Press SWITCH button to WIRELESS PROTOCOL.
MODE SWITCH
MODE SWITCH
MENU
DMX MODE: CCT 16bit
DMX PIEXL: 01
MENU
DMX MODE: CCT 16bit
DMX PIEXL: 04
MENU
DMX MODE: CCT 16bit
DMX PIEXL: 04
MENU
BT: RESET
WIRELESS PROTOCOL: V1.0

10
Press + - button to select V1.0 or V2.0.
⑥Bluetooth Reset
Press SWITCH button to BT.
MODE SWITCH
MODE SWITCH
MENU
BT: RESET
WIRELESS PROTOCOL: V1.0
MENU
BT: RESET
WIRELESS PROTOCOL: V2.0
MENU
BT: RESET
WIRELESS PROTOCOL: V2.0
MENU
WIRELESS PROTOCOL: V2.0
BT: RESET

11
Press + - button to enter the interface of bluetooth reset.
MODE SWITCH
MENU
WIRELESS PROTOCOL: V2.0
BT: RESET
BT RESET
BACK RESET
BT RESET
BACK RESET
BT RESET
BACK RESET
Press SWITCH button to RESET.
MODE SWITCH

12
⑦Firmware update
(1)Firmare update for the wire controller
Switch off the the wire controller, and then insert the USB flash drive with the new firmware for wire controller,
the screen will show as below:
Press MODE button to confirm reset and it will return to the menu interface after resetting the bluetooth.
Press SWITCH button to UPDATE.
FOUND FIRMWARE
V1.00.10
BACK UPDATE
FOUND FIRMWARE
V1.00.10
BACK UPDATE
MODE SWITCH
MODE SWITCH
MENU
WIRELESS PROTOCOL: V2.0
BT: RESET
BT RESET
BACK RESET

13
(2)Firmware update for fixtures via wire controller
Switch on the controller and connect it to the fixture to be upgraded, insert the USB flash drive with the new
firmware of the fixture, turn on the fixture, then press the MODE button to switch to the menu interface.
Press MODE button to confirm the update, it will prompt "FIRMWARE UPDATED" after the firmware is upgraded.
FIRMWARE UPDATING
......
In the menu, press the SWITCH button to firmware update.
FOUND FIRMWARE
V1.00.10
BACK UPDATE
FIRMWARE UPDATED
MODE SWITCH
MODE SWITCH
MENU
VERSION：V1.00.10
FW: UPDATE
MENU
WIRELESS PROTOCOL: V2.0
BT: RESET

14
Press SWITCH button to UPDATE.
SEARCHING FOR
FIRMWARE FILE
......
Press + - button to enter the firmware update interface.
MODE SWITCH
MODE SWITCH
MENU
VERSION：V1.00.10
FW: UPDATE
FOUND FIRMWARE
PavoBulb_10C_FW
BACK UPDATE
FOUND FIRMWARE
PavoBulb_10C_FW
BACK UPDATE
FOUND FIRMWARE
PavoBulb_10C_FW
BACK UPDATE

15
⑧Version
Press SWITCH button to VERSION.
Press MODE button to confirm the update, it will prompt "FIRMWARE UPDATED" after the firmware is upgraded.
FIRMWARE UPDATING
...... FIRMWARE UPDATED
MODE SWITCH
MODE SWITCH
FOUND FIRMWARE
PavoBulb_10C_FW
BACK UPDATE
MENU
FW: UPDATE
VERSION: V1.00.10
MENU
FW: UPDATE
VERSION: V1.00.10

16
Notice
1. The wire controller is only compatible with PavoBulb 10C and PavoTube T8-7X.
2. When the battery level is low, it is recommended to reduce the brightness to less than 50% for charging, or turn it
off and fully charge before using again.
3. When the wire controller is not connected to the fixture and is powered off, connect the power supply, now the
display will show " " and icon is scrolling; when the battery is fully charged, the display shows " ".
7. USB Type C port: For firmware updates, or connect with the USB cable, and then connect to the USB adapter with
an output of 5V/2A or above to charge the wire controller.
8. The wire controller has a built-in lithium battery and can power the PavoBulb 10C and PavoTube T8-7X directly.
9. Please switch off the controller when not in use.
This manual has been compiled according to the rigorous testing of our company's products. Product designs are
subject to change without prior notice. You can download the latest version of the manual for this particular product
from www.nanlite.com.

[phone]
[e-mail]
[phone]
Zhanglin,324,Dongli Chenghai Shantou Guangdong China
Version: V2 2022-02-16
www.nanlite.com