Naomi Kids Hide-a-Desk User manual

Assembly Instructions
Product Dimensions:
38” L x 27” D x 26” H
Please take a moment to read through the entire instruction booklet before assembly to
familiarize yourself with this product. Once you feel ready to start, follow the instructions
step by step and this should make this process as easy as we could make it for you.
If you need help or have damaged or missing parts, contact customer service at
www.NaomiHome.com.
Page 1 of 11
NAOMI
Low Loft Bed - Hide-a-Desk
KIDS
©
2018 Naomi Home Inc. - All Rights Reserved.

Page 2 of 11
ADULT ASSEMBLY REQUIRED
CHOKING HAZARD
•
•
USE, MAINTENANCE & ASSEMBLY
PARENTAL SUPERVISION IS REQUIRED
WARNING CAUTION
STRANGULATION HAZARD
SAFETY WARNINGS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This product includes small parts, sharp points and sharp edges in its unassembled state.
Keep unassembled parts away from children under 3 years of age, and animals.
Never attach or hang items to any part of the desk that is not designed for use with
the desk; for example, but not limited to hooks, belts, and jump ropes.
Follow the information on the warnings appearing on the loft bed end structure and on the
carton. Do not remove warning label from bed.
Do not allow children under 3 years of age to use the hide-a-desk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Children have died from furniture tip-over.
To reduce the risk of furniture tip-over:
ALWAYS install tip-over restraint especially if used by a wall or in the open.
NEVER put a TV on this product
NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
NEVER open more than one drawer at a time.
ALWAYS place heaviest items in lowest drawers.
This Naomi Home Kids product is intended for child use age 3+.
Parents or Guardians should supervise use under the intended age specifically regarding
children that may have access to it and climb on the unit.
Do not allow horseplay on, under, or behind the unit and prohibit jumping on the desk.
If used improperly, your desk may be pulled over or fall, creating risk of injury or
damage. Children should not be permitted to climb or pull on the hide-a-desk.
Periodically check and ensure that the components are in their proper position, free from
damage, and that all connectors are tight.
Use on level surfaces only. Assemble on a soft level surface to avoid damage to unit or floor.
Do not use this item if any components are missing or damaged.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Only clean using damp cloth and mild detergent, do not use bleach or abrasive cleaners.
Check you have all components and tools listed on page 4
Do not stand or put weight on this product during assembly, this could cause damage.
Remove all hardware from the plastic bags and separate them into groups.
Assemble the item as close to its final position (in the same room) as possible.
Certain assembly steps may be easier with 2 people.
Dispose of all packaging carefully and responsibly.
We do not recommend power screwdrivers. Only use hand screwdrivers to prevent
damage to unit.
•
Enfants morts suite au basculement d’un meuble.
Afin de limiter le risque de basculement de meuble:
TOUJOURS utiliser les fixations anti-basculement.
NE JAMAIS installer de TV sur ce produit.
NE JAMAIS laisser d’enfants se tenir debout sur les tiroirs,
portes ou etageres, y grimper ou s’y suspendre.
NE JAMAIS ouvrir plus d’un tiroir a la fois.
TOUJOURS placer les choses les plus lourdes dans les tiroirs du bas.
Han muerto ninos por el vuelco de meubles.
Para limitar el riesgo de vuelco de los meubles:
Utilisar SIEMPRE las fijaciones antivuelco que suministran.
NUNCA instalar un TV sobre este producto.
NUNCA permitar que los ninos se pongan de pie, trepen o
se cuelguen de los cajones, puertas o baldas.
NUNCA abrir mas de un cajon a la vez.
Colocar los objetos mas pesados en los cajones inferiores.
•
•
•
•
•
•
•
•
•
•
!
FURNITURE TIP-OVER HAZARD
•

Phillips Screwdriver
(Medium)
Allen Wrench
(included)
This drawing is to give you an overall idea only of how this assembly will go together and does
not replace the assembly instructions.
Please take a moment to read through the whole instruction booklet before assembly to familiarize
yourself withthisproduct . Once you feel ready to start, follow the instructions step by step and thisshould
mak e thisprocess as easy as we could make it for you.
Due to the number of parts involved
assembly can take a few hours
so set aside between 30 minutes and
1 hour to assemble this
without rushing.
ASSEMBLY AT A GLANCE
Page 3 of 11
11
10
10
12
4
3
2
5
5
1
6
6
7
8
9
I
J
TOOLS REQUIRED

COMPONENT PARTS
Please check that you have all the parts listed below
Small Screw
M3.5x12mm x 8
Long Bolt
M6x30mm x 8
ASSEMBLY HARDWARE
FE
Medium Bolt
G
M6x35mm x 3 M6x25mm x 6
Short Bolt
H
*Note: follow the setup of
of bed frame Option 1
for ladder right / desk left
conguration or Option 2
for ladder left / desk right
conguration.
1. Bookcase Left x1
2. Bookcase Right x1
3. Bottom Shelf x1
4. Middle Shelf x1
5. Shelf Back x2
6. Desk Shelf Support x2
7. Desk Top x1
8. Desk Support x1
9. Rear Slide Stopper x1
10. Slide Support x2
11. Left Slide x1
12. Right Slide x1
I. Caster Wheel (Locking) x1
J. Caster Wheel x1
Wood Dowel Pin
x 16
Allen Wrench
M6x38mm x 20
B
A
Hex Bolt
C
x 1 M3.5x30mm x 2
Large Screw
D
Page 4 of 11
I
J
4
3
2
1
6
7
8
9
5
11
10
12

ASSEMBLY INSTRUCTIONS
2
1
Select 10 x2, 11, 12, F x4.
7, 8, G x3. Position 11
with bottom of L facing
center, and 12 the oppo-
site L facing center. Place
10 on end of 11 and 12,
and insert F through 10
into 11 and nger
tighten. Repeat F for
other end and 12 ends.
Tighten F with C wrench.
Page 5 of 11
Select 7, 8, G x3. On at soft
surface position 7 upside
down and align holes center
7 to 8. Insert G x3 through 8
into 7 and tighten with C.
F
F
F
F
10
10
11
12
C
7
G8

ASSEMBLY INSTRUCTIONS
4
3
Select 1, 3, 4, 5 x2, 6 x2, A
x8, B x8. Position 1 left, 3
bottom, 4 middle. Align 5
as backer over 3, repeat
2nd 5 over 4. See Large
Image, insert A into end of
5 large hole, also A into
large hole of 3 and 4. Insert
A into other corner large
hole on same end of 3 and
4. Insert B through 1 into 5
and nger tighten. Repeat
other 5. Insert B through 1
into 3 x2 bottom hole and
top hole and repeat for 4.
Insert A into large hole in
end of 6 x2. Ax 6 to top
of 1 with B and repeat
other top hole with 2nd 6
and B. Tighten all Bs with C.
Select 2, A x8, B x8.
Repeat As into 3 x2, 4 x2,
5 x2, 6 x2. Align holes of
2 to the assembly so top
of 2 is by 6s and bottom
is by 3&5. Ax 2 to
assembly using B x8.
Tighten all Bs with C.
Page 6 of 11
A
A
A
B
A
5
A
B
5
5
4
3
6
6
1
A
A
A
B
3
1
6
2

ASSEMBLY INSTRUCTIONS
6
5
Select B x4. Insert B x2
into bottom holes of 3
and into 5. Tighten with
C. Repeat for B x2 into 4
and other 5.
Turn assembly upside down
with 6s toward the oor. On
the right corner (left side
when up correctly), ax J
non-locking caster wheel to
3 using E x4. Repeat for I
locking caster on left corner
(right side when up
correctly). Ax I using E x4
to underside of 3.
Page 7 of 11
Bx2
B
B
3
4
J
E
6
3J
E
E
I

ASSEMBLY INSTRUCTIONS
7
Select H x6. On at soft
surface, place 7 upside
down. Position book-
case assembly with
wheels up over the top
of 7 at the end with
rounded corners oppo-
site of 8 support.
Ensure the wheels and
bookcase face outward.
Ax the bookcase to
the desk top using H x6.
Insert H through hole in
6 and into 7. Repeat
other 5 holes. Tighten
with C.
Page 8 of 11
8
Option 2 - Ladder Left Skip
to Step 10. Option 1 -
Ladder Right. Select desk
slide assembly, F x4. Two
person assembly. Position 11
at the far end opposite the
ladder and 12 toward the
center with 10s at the back
and front. Make sure bottom
of 11 “L” faces downward.
Ax the desk slide assembly
to the bed frame at end
opposite ladder. Insert F into
hole in 10 and into part 8 side
board of Bed Frame. Repeat
for 2nd hole in 10. Insert F
into hole in 10 and into part 7
side board of Bed Frame.
Repeat for other F into 10 and
7. Tighten F with C wrench.
8
7
H
H
6
6
F
8
7
10
10
11
12
F

ASSEMBLY INSTRUCTIONS
9
Option 1 - Ladder
Right. Select 9, D
x2. Align desk top
to the desk slides
and insert desk
top. Place 9 over
holes in end of
desk top 7 (under
bed mattress
slats). From under-
side of desk, insert
D through 7 and
into 9. Repeat
other 9 and
tighten with
screwdriver. Desk
stopper secured.
10
Option 2 - Ladder Left.
Select desk slide assembly, F
x4. Two person assembly.
Position 12 at the far end
opposite the ladder and 11
toward the center with 10s
at the back and front. Make
sure bottom of 12“L” faces
downward. Ax the desk
slide assembly to the bed
frame at end opposite
ladder. Insert F into hole in
10 and into part 8 side board
of Bed Frame. Repeat for 2nd
hole in 10. Insert F into hole
in 10 and into part 7 side
board of Bed Frame. Repeat
for other F into 10 and 7.
Tighten F with C wrench.
Page 9 of 11
F
8
7
10
10
11
12
F
DD
9

ASSEMBLY INSTRUCTIONS
Page 10 of 11
11
Option 2 - Ladder
Left. Select 9, D
x2. Align desk top
to the desk slides
and insert desk
top. Place 9 over
holes in end of
desk top 7 (under
bed mattress
slats). From under-
side of desk, insert
D through 7 and
into 9. Repeat
other 9 and
tighten with
screwdriver. Desk
stopper secured.
D
D
9
DESK COMPLETE

DESK ASSEMBLY COMPLETE
Page 11 of 11
www.NaomiHome.com
MADE IN CHINA
Product Packaging Information
Model #:
Color:
Shipment Ref. #:
Date:
________________________________
__________________________________
_________________________
__________________________________
CONGRATULATIONS, YOUR NAOMI HOME KIDS
LOW LOFT BED - HIDE-A-DESK IS COMPLETE!
NAOMI
KIDS