Napier SPORTZ LINK 51000 User manual

CAUTION
•Keep all flame and heat sources away from the tent fabric.
The tent is made with flame-resistant fabric which meets
CPAI-84 specifications. This does not make it fireproof.
The fabric will burn if left in contact with any flame source.
The application of any foreign substance to the tent fabric
may render the flame-resistant properties ineffective.
•To prevent carbon monoxide from entering the vehicle and
tent area, do not run the engine, do not cook inside the tent,
and do not use a gas heater in the tent. Carbon monoxide is
dangerous to your health.
•Engine must be off and exhaust must be fully cooled before
tent installation and use.
•Do not use candles, matches, or open flames of any kind in or
near the tent
•Do not cook inside the tent
•Build campfires downwind and several meters away from the
tent. Be sure to fully extinguish fires before leaving a
campsite or before retiring for the night
•Exercise extreme caution when using fuel-powered lanterns
or heaters inside or around the tent. Use battery-operated
lanterns whenever possible
•Do not refuel lamps, heaters, or stoves inside the tent
•Extinguish or turn off all lanterns before going to sleep
•Do not smoke inside the tent
•Do not store flammable liquids inside the tent
•NEVER run the vehicle engine when the tent is attached
•Do not install the tent when the temperature is below
0ºC/32ºF or when your vehicle is wet, it may cause damage
•Allow adequate ventilation inside the tent at all times
•Do not attempt to drive the vehicle with the tent attached
CAMPSITE SELECTION
•Select a smooth, level campsite clear of rocks,
branches, and other hard or sharp objects
•Avoid areas with overhead power lines and tree limbs
•Park the vehicle in the chosen campsite
•Turn the engine off and engage the parking brake
WARNING
HOW TO STORE
WARRANTY INFORMATION
1. Clean and dry the tent
2. Fold all of the components into the tent
3. Roll the tent, using the pole bag as a guide
4. Secure with the tent tie straps and insert
into the carrying bag
5. Store in a cool, dry place
Napier tents have a one (1) year warranty period from the time of purchase against defects in improper
workmanship. Normal wear and tear, seam leakage through needle holes, and improper use, abuse, or
alteration are not covered under the warranty policy. Napier Outdoors will replace or repair defective parts.
Replacement parts may be new or re-built at Napier’s sole discretion. E-Warranty claim forms can be
completed online at www.napieroutdoors.com/warranty. Proof of purchase (receipt) must be provided. If you
do not provide proof of purchase, or if your warranty period has ended, replacement parts can be purchased.
To order replacement parts, contact Napier Outdoors at 800-567-2434 (9:00 am – 5:00 pm EST),
visit www.napieroutdoors.com, or email [e-mail]
BEFORE
YOU BEGIN
instructions
LINK
MODEL 51000

Set-up your Napier Truck Tent per the instructions
provided in the carrying bag.
Lay out the Sportz Link Tent with the vehicle sleeve facing the bed of your truck.
1
PACKAGE CONTENTS
tent set up
2
TENT BAG
TENT TIE STRAPS (2)
TENT POLE BAG
STAKE BAG
TENT POLES (2) AWNING POLE (1)
RAINFLY GEAR LOFT
STAKES (10)
Remove contents from the bag and ensure you have all components listed below.
If you are missing parts, please contact Napier Outdoors at 800-567-2434 | Monday - Friday or email [e-mail]

Attach the pole clips found on the tent
to the poles.
Assemble the tent poles by
unfolding each section. You will
have 2 long poles (tent structure)
and 1 short pole (rainfly).
Insert the tent poles diagonally, corner-to-corner, into the pole sleeves. The center of
the poles should cross and form an X.
NOTE: The poles may get stuck in the pole sleeve. Do not force the pole –
gently lead it through the fabric sleeve.
34Insert one end of the pole into the
grommet hole located in the corner of
the tent. Go to the opposite end of the
pole and gradually apply pressure to
the pole, forming an arch until you are
able to insert the pin into the grommet
hole. Repeat for the second pole.
5
6From inside the ground tent, unzip the door and mesh that faces
the truck bed. Roll up the mesh and door and secure with T-straps.
Move the tent towards the tailgate of the truck. Slip the sleeve
under the bumper and over the entrance of the truck tent. Ensuring
the sleeve is over the vestibule pole.
Outside of the tent, secure the tent to your vehicle:
A. Attach the bottom outside J-Hook strap to any part
of the wheel well and tighten (1 per side).
NOTE: Ensure the exhaust pipe is outside of the
sleeve.
7
8
9

Attach the rainfly to the
clips found at the bottom
corners of the tent.
Tighten the straps and
secure the Velcro tabs
around the poles.
Locate the rainfly pole and
insert it into the sleeve
located above the door.
Place the end of the pole
into the grommet hole
located on the pole sleeve.
Repeat on the other side
Stake the rainfly guy lines
to the ground.
B. Attach the clips located on the
tent to the corner-to-corner pole on
the truck tent (1 per side).
Stake down the tent through the
corner and entrance webbing loops.
910
Drape the rainfly over the tent. The side that says “Truck Tent Side” goes towards the truck.
11
12
13
14
To install the gear loft, place each
corner hook of the gear loft into the
loop located on the ceiling of the tent.
15
attaching the rainfly
13
12
13