Napoleon VPrestige PF600 Manual

BUILT-IN PF UNIT INSTRUCTION GUIDE
N415-0111/NOV29/05
Please use this manual in conjuction with your main manual to properly assemble your built-in grill. Refer to the main manual for operat-
ing, cleaning, and maintenance instructions. The operating instructions are also located on the bottom of the side burner lid. This grill is
designed for masonry, non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes.
BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as
shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an
approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane Installation Code in
Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"
for rigid pipe, and 5/8" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN
B149.1. Propane Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States. If the enclo-
sure is to house a propane cylinder, the tank portion of the enclosure must be ventilated according to local codes, and must not have
communication with the cavity used to enclose the gas grill. The tank can not be stored below the gas grill.
BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as
shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an
approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane Installation Code in
Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"
for rigid pipe, and 3/4" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN
B149.1. Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States.
Built in units are supplied with a drip pan which holds only a minimal amount of grease. To prevent grease fires, the pan must
be cleaned after each use. Access must be provided to the inside of the enclosure to make gas connections.
SERIAL #______________________
8f”
20 e”
7”
8¼”
8¼”
34”
RECOMMENDED
4”
6”
55¾”PF600UNITS
46¾” PF450UNITS
2”MIN
ELECTRICALBOX
OPENING CENTEROFELECTRICALBOXMUSTBEWITHIN3
FEETOFLEFT EDGEOFGASGRILL
ELECTRICALWIREACCESS
OPENING(4”x4”)
GASINLETOPENING
(4”x4”)
MINIMUM10SQINOFVENTILATION
REQUIREDONEACHENDOFCABINET
OPENINGDIMENSIONS

H
W
D
NOTE:ACCESSORYFRAMES OVERLAP
OPENINGBY1 ½”ONALL4SIDES
Part # Description Picture WH
N370-0070 Flat horizontal painted door
N370-0357SS
N370-0358SS
13¼” 18 ¼”
OPENINGDIMENSION
N370-0356SS Curved stainless steel door - 308 size
N370-0072 Flat horizontal stainless steel door
N370-0069 Flat vertical painted door
N370-0071 Flat vertical stainless steel door
Curved stainless steel door - 450 size
Curved stainless steel double door - 600 size
N370-0361 PF style stainless steel door
N370-0359 PF style stainless steel single drawer
N370-0360 PF style stainless steel triple drawer
13¼” 18 ¼”
18¼” 13 ¼”
18¼” 13 ¼”
22½” 19 ¾”
27” 19 ¾”
17” 23¼”
17¼” 6¾”
17¼” 22 ¾”
BUILT-INACCESSORYOPENING DIMENSIONS
35¼” 19”
23”
23”
D

1. Lower the unit into the opening. Feed the wiring harness through the opening on the left hand side. Feed the gas flex
connector and regulator down through the opening on the right hand side.
2. Remove the electrical box cover. Install the electrical box into the opening (fasteners not included). Feed the three
white wires coming from the grill head into the hole in the back of the electrical box. Ensure the snap bushing is inserted
into the hole. Feed the black electrical cord from the inside out through the same bushing. If you are connecting the
power directly to the GFI outlet, disconnect the black electrical cord and use the same terminals on the GFI to connect the
power. Attach the white wires to the transformer output. The two wires marked T2 to one output, and the one wire
marked T1, to the other output. Re-install the electrical box cover. Plug the power cord into a suitable GFI protected
outdooroutlet.
3. For natural gas units, mount the regulator to the cabinet. Connect the gas supply to the inlet side of the regulator. For
propane units, connect the gas supply to the end of the flexible connector.
4. If using the optional trim kit, install the rear and side trim pieces using a dab of silicone.
5. Leak test the entire installation before operating the unit.
N570-0046
OPTIONAL
TRIMKIT
N370-0362
ELECTRICALBOX

1. Unpack the drawer frame assembly.
2. Remove the drawers from the enclosure by fully extending them and then lifting up to remove them from the slides.
3. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located at the
same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to ensure that
the front of the enclosure is plumb.
4. Once the enclosure is level and square, fasten into place. (Fasteners not included).
5. Re-install the drawers by tipping the back of the drawer down into the slide. Once the wheels are inserted into the slide,
lower the front of the drawer until it is level, then push in. Note: if the enclosure is installed with shims that are too thick,
the wheel will not engage into the slide. The shim thickness will need to be reduced.
6. Remove the protective coating from all remaining surfaces.
1. Unpack the door and frame.
a. For the curved stainless steel single doors, remove the door from the frame by lifting the door while holding on to the
pivot rod. This will allow the pivot rod to come out of the hole on the bottom of the frame.
b. For the curved stainless steel double doors, with the door in the open position, simply lift the doors off of the hinges.
c. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw on the hinge
furthest away from the door. This will allow the hinge to separate.
2. Center the frame in the opening. Starting with the hinged side, shim between the frame and side wall of the opening.
Ensure the shims are close to the hinge on the PF style doors. When the frame side wall is plumb, fasten it to the cabinet
with screws (not provided). Attach the other side of the frame in the same fashion, ensuring the frame is square.
3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and bottom of the frame.
The curved stainless steel double door frame must be fastened in the center both at the top and bottom.
4. Once the frame has been secured and checked for squareness, the door can be re-installed.
5. Remove the protective coating from all remaining surfaces.
BUILT-IN ACCESSORY DRAWER INSTRUCTIONS
BUILT-IN ACCESSORY DOOR INSTRUCTIONS