NatComm EASY-TRANSFER User manual

EASY-TRANSFER
USER GUIDE
For Technical Assistance
Please Phone: [phone]

Page 2 National Communications
PACKING LIST
Before commencing installation, please check that you have the following
items:
Description Quantity
EASY-TRANSFER Line Sharer 1
Power Supply 1
Telephone Cable with Female Socket 2
Telephone Cable with Male Socket 1

National Communications Page 3
DESCRIPTION
Our EASY-TRANSFER Line Sharer is designed to connect to ANY
TELEPHONE SOCKET and then allow TWO standard telephones that
are connected direct to it, to operate as extensions of your ordinary
single telephone line.
You can then transfer a call, from one of the telephone extensions
connected to EASY-TRANSFER, to the other telephone extension, by
dialing *.
When transferring a call, you will be able to privately communicate with
the other extension while the call is silently on hold. The party on hold
will be connected to either EASY-TRANSFER extension, as soon as
the other extension hangs up.
You can make an intercom call, from one of the telephone extensions
to the other at any time, by simply dialing *. EASY-TRANSFER will
then ring the other telephone extension and once the other party answers,
you will be able to communicate just as if you had made a telephone
call.
EASY-TRANSFER is designed to work with all standard residential
telephones.
NOTE - In the event of a power cut, ONLYTHE TELEPHONES
CONNECTED TO PORT EXT B WILL RING.

Page 4 NationalCommunications
INSTALLATION

National Communications Page 5
INSTALLATION
1. Unplug all equipment from the telephone socket to be used.
2. Connect the TELEPHONE LINE port of EASY-TRANSFER to ANY
telephone socket using the supplied cable with male plug.
3. Connect your two telephones to the EASY-TRANSFER ports labelled
EXTENSIONA& EXTENSION B using the remaining supplied cables
with female sockets.
NOTE - If one of the telephones to be connected is located in a
different room (or floor), then you will need to connect it with a
telephone extension of an appropriate length (not supplied), or you
will need to have it connected to EASY-TRANSFER by a technician,
who will either use existing wiring within your walls or install new
wiring within your walls, to provide connection to EASY-TRANSFER.
4. Connect your power supply and switch the power ON.
5. Refer to the section DIP SWITCH SETTINGS (see pages 8-10), in
order to set EASY-TRANSFER to meet specific user requirements.
For the contact details of a recommended technician in your area,
please contact National Communications on ph [phone].

Page 6 National Communications
OPERATION
Once your EASY-TRANSFER device has been installed as per our
instructions, you will be able to transfer an incoming or outgoing call
from any telephone connected to your line (including those telephones
not connected direct to an EASY-TRANSFER), to either telephone
connected to the EASY-TRANSFER.
CALLS BETWEEN TELEPHONES
CONNECTED TO EASY-TRANSFER
You can make an intercom call between telephone extensions connected
to the same EASY-TRANSFER by dialing *.
You can transfer a call, at any time, between telephone extensions
connected to the same EASY-TRANSFER, by dialing *.
When transferring calls, you will be able to privately communicate with
the other extension while the call is silently on hold. The party on hold
will be connected to either EASY-TRANSFER extension, as soon as
the other EASY-TRANSFER extension hangs up.
TRANSFERRING CALLS TO ATELEPHONE
CONNECTED TO EASY-TRANSFER
To TRANSFER a call from a telephone not connected to your EASY-
TRANSFER, just press the appropriate TRANSFER CODE (selected by
dip switches on the underside of EASY-TRANSFER) and then HANG
UP. The called EASY-TRANSFER extension will RING until it is
answered, or up to a maximum of 7 rings.
Note: You should always ensure that the call has been answered at
the remote extension. If the call has not been answered, you should
pick up any telephone connected to the line to resume the call.

National Communications Page 7
USER OPTIONS
PRIVATE MODE or PARTY MODE
You can set telephones connected to EASY-TRANSFER to operate
in either PRIVATE MODE or PARTY MODE :
PRIVATE MODE - When all telephones connected to an EASY-
TRANSFERaresetinPRIVATEMODE,onlyONEtelephoneconnected
toEASY-TRANSFERcanparticipateinatelephoneconversationatthe
same time. Only the first device to answer (or make a call) can access
the telephone conversation. Subsequent phones picked up will not be
able to hear or participate in a conversation.
Note - Telephones NOT connected to EASY-TRANSFER cannot be
blocked from the line.
PARTY MODE - When all telephones connected to EASY-TRANSFER
are set in PARTY MODE, ALL telephones connected to the line can
participate in a telephone conversation at the same time.
TELEPHONESTORING
It is possible to set ONE telephone connected to EASY-TRANSFER to
NOT RING whenever there is an internal call.
The telephone connected to port EXT A can be set to NOT RING by
using the Dip Switches located on the underside of the unit (see page
10 for further details).
NOTE - In the event of a power cut, ONLYTHE TELEPHONES
CONNECTED TO EXT B WILL RING.

Page 8 National Communications
DIP SWITCH OPTIONS
The settings of the DIP SWITCHES located on the underside of the
EASY-TRANSFER allow the user to:
A) SET THE TRANSFER CODE FOR EACH TELEPHONE.
Required if calls are to be transferred from a telephone not
connected to EASY-TRANSFER.
B) DETERMINEWHICHTELEPHONESAREREQUIREDTORING
WITH AN INCOMING CALL.
This facility can stop INCOMING calls from ringing on the Extension
A port of EASY-TRANSFER.
C) SET TELEPHONES TO WORK IN PARTY OR PRIVATE MODE.
PARTYMODE
All telephones connected to EASY-TRANSFER can participate in a
telephone conversation at the same time in the same manner as has
beenexperienced beforethe fittingofyourEASY-TRANSFER.
PRIVATEMODE
OnlyONEtelephoneconnectedto EASY-TRANSFERcanparticipatein
a telephone conversation at the same time. Only the first device to
answer (or make a call) can access the telephone conversation.
Subsequent phones picked up will not be able to hear or participate
inaconversation.

National Communications Page 9
DIP SWITCH SETTINGS
SWITCH 1 - If set to ON, the telephones connected to this unit will
operate in PARTY mode.
- If set to OFF, the telephones connected to this unit will
operate in PRIVATE mode.
SWITCH 2 - If set to ON, both telephones attached to this unit will
RING with an incoming telephone call.
- If set to OFF, only the telephone connected to port B or
this unit will RING with an incoming telephone call.
SWITCH 3 : SWITCH 4
ON ON Transfer Code forAis 1
Transfer Code for B is 2
ON OFF Transfer Code forAis 3
Transfer Code for B is 4
OFF ON Transfer Code forAis 5
Transfer Code for B is 6
OFF OFF Transfer Code forAis 7
Transfer Code for B is 8

Page 10 National Communications
EXAMPLES
1. To set a telephone to respond to TRANSFER CODE 3
Set dip switches 3=ON, 4=OFF
This telephone must be connected to port A.
2. To set a telephone to respond to TRANSFER CODE 4
Set dip switches 3=ON, 4=OFF
This telephone must be connected to port B.
3. To set a telephone to respond to TRANSFER CODE 3 where
you require its phone to operate in PARTY MODE.
Set dip switches 1=ON, 3=ON, 4=OFF
This telephone must be connected to port A.
4. To set a telephone to respond to TRANSFER CODE 3
where you require this telephone to ring whenever an
incoming call is detected.
Set dip switches 2=ON, 3=ON, 4=OFF
This telephone must be connected to port A.
5. To set a telephone to respond to TRANSFER CODE 3 but
where this telephone will not ring whenever an incoming call
is detected.
Set dip switches 2 = OFF, 3 = ON, 4 = OFF
This telephone must be connected to port A and will only ring
when an internal or external call is transferred to it.

National Communications Page 11
NOTES

Page 12 National Communications
SPECIFICATIONS
Dimensions(all in mm) :106 (W) x 106 (D) x 43 (H)
Weight :225g
Power Supply : 12VAC/500mA
Power Consumption :Idle - 0.5 Watts
Power Consumption :Call - 0.75 Watts
Telephone Line In Connector :RJ 11 6 pin (2 centre)
ExtensionAOut Connector :RJ 11 6 pin (2 centre)
Extension B Out Connector :RJ 11 6 pin (2 centre)
Power Connector :2.5mm barrel connector
ACMA COMPLIANT :Supplier Number N 782
WARRANTY
This device is guaranteed against defects from workmanship for a period
of two years (24 months) from the date of purchase. In the event of
failure, you should return the product, along with proof of purchase date,
and a written statement about the nature of the problem.
This Warranty shall not apply to any unit which has been subject to
alteration, modification, abuse, negligence, accident, external voltage/
lightning surge or used in any manner contrary to these instructions.
The obligation is solely to repair or replace the product. The warrantor
is not liable for any incidental or consequential damages due to such
defects.
The user is responsible for freight costs to the repair point. The warrantor
will be responsible for freight costs in returning this unit back to the
user.
Damage caused to this device or attached equipment, by lightning strikes
or over voltage surge is not covered under this warranty.
CASE SEALED AT FACTORY
OPENING THE CASE VOIDS THE WARRANTY