National Instruments ATCA-3671 User manual

GETTING STARTED GUIDE
ATCA-3671
FPGA Module for ATCA
This document describes how to install, configure, and test the ATCA-3671 FPGA Module for
ATCA. The ATCA-3671 is programmable both through LabVIEW using LabVIEW FPGA and
through BEEcube Platform Studio (BPS).
Note If you are using BPS, visit ni.com/info and enter the Info Code BPSsupport
to access BPS-related resources within the BPS Support Community.
This icon denotes a caution, which advises you of precautions to take to avoid injury,
data loss, or a system crash.
Caution You can impair the protection provided by the ATCA-3671 if you use it in
a manner not described in this document.
Contents
Electromagnetic Compatibility Guidelines...............................................................................2
Verifying the System Requirements..........................................................................................2
Unpacking the Kit..................................................................................................................... 3
Verifying the Kit Contents................................................................................................ 3
Preparing the Environment....................................................................................................... 5
Installing the Software.............................................................................................................. 5
Installing the Hardware.............................................................................................................6
Protection Impairment.......................................................................................................6
Installing the RTM............................................................................................................ 6
Installing the ATCA-3671 Module................................................................................... 7
Installing AIO-3681/3682 Modules.................................................................................. 7
Installing AIO-3691 Modules......................................................................................... 12
Powering On the ATCA-3671 Module................................................................................... 15
Maximum Power Requirements......................................................................................16
Connecting to a Host Computer..............................................................................................17
Installing MXI Cables.....................................................................................................17
Identifying FPGA Devices in MAX............................................................................... 17
Network Connection Configuration to the ATCA-3671................................................. 18
Programming...........................................................................................................................18
Finding Example VIs...................................................................................................... 18
Verifying the Device Connection (Optional).................................................................. 18

Removing Modules................................................................................................................. 19
Removing the ATCA-3671 Module................................................................................19
Removing the RTM.........................................................................................................19
Removing the ATCA I/O Module...................................................................................19
Front Panels and Connectors...................................................................................................19
ATCA-3671 Front Panel................................................................................................. 19
RTM-3661 Front Panel................................................................................................... 23
ATCA Compatibility vs. Compliance..................................................................................... 23
Troubleshooting...................................................................................................................... 23
Should I Update Device Firmware and FPGA Images?................................................. 23
Why Doesn't the Device Power On?...............................................................................23
Why Doesn't the Device Appear in MAX?.....................................................................24
Where to Go Next................................................................................................................... 24
Worldwide Support and Services............................................................................................ 25
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with
radio and television reception and prevent unacceptable performance degradation, install and
use this product in strict accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by National
Instruments could void your authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance, operate this product only with
shielded cables and accessories. Fiber optic cables connected to SFP+ and QSFP+
ports do not require shielding.
Caution To ensure the specified EMC performance, the length of any cable
connected to the Ethernet port and the Mini-SAS HD ports must be no longer than
30 m (100 ft.). The lengths of fiber optic cables connected to the SFP+ or QSFP+
ports are not controlled. The length of any cable connected to any other port must be
no longer than 3 m (10 ft.).
Verifying the System Requirements
To use the NI ATCA FPGA Modules instrument driver, your system must meet certain
requirements.
2| ni.com | ATCA-3671 Getting Started Guide

Refer to the product readme, which is available online at ni.com/manuals, for more
information about minimum system requirements, recommended system, and supported
application development environments (ADEs).
Unpacking the Kit
Caution To prevent electrostatic discharge (ESD) from damaging the device,
ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the device from the package and inspect the device for loose components or any
other sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the device in the antistatic package when the device is not in use.
Verifying the Kit Contents
• ATCA-3671 module
• Ethernet cable
• ATCA I/O slot blockers (x4)
•ATCA-3671 Getting Started Guide (this document)
Note Your ATCA-3671 kit may contain additional NI ATCA products.
ATCA-3671 Getting Started Guide | © National Instruments | 3

Other Equipment
Required Items
In addition to the kit contents, you must provide the following additional items:
• A chassis from the following list:
– Single-Module ATCA Chassis1
– 14-Slot ATCA Chassis
Note If your kit does not include a chassis, you can purchase one from ni.com
or by contacting your local NI sales representative.
• Rear transition module (RTM) from the following list:
– (Recommended) RTM-3661 PCI Express Rear Transition Module for ATCA1
– RTM-3662 High-Speed Serial Rear Transition Module for ATCA
Note The RTM-3662 is supported only in BPS. To access BPS-related
resources and documentation for the RTM-3662 within the BPS Support
Community, visit ni.com/info and enter the Info Code BPSsupport.
• DC power supply1 as described in the device specifications
• Number 2 Phillips screwdriver
• Number 1 Phillips screwdriver
• Small flat-blade screwdriver
• Host PC or laptop
ATCA I/O Modules (Optional)
In addition to the required items, you may choose to provide one or more of the following
ATCA I/O modules.
• AIO-3681 Digitizer Module for FMC, with the following components:
– Riser card (x1)
– Male-to-female M2.5 standoffs (10 mm hex length, 6 mm thread length) (x2)
– Male-to-female M2.5 standoffs (12.5 mm hex length, 3.5 mm thread length) (x2)
– M2.5x8 screws (x2)
– M2.5x6 screws (x2)
• AIO-3682 Signal Generator Module for FMC, with the following components:
– Riser card (x1)
– Male-to-female M2.5 standoffs (x4)
1Included in some ATCA-3671 kits.
4| ni.com | ATCA-3671 Getting Started Guide

– M2.5x8 screws (x2)
– M2.5x6 screws (x2)
• AIO-3691 High-Speed Serial Adapter Module2, with the following components:
– Female-to-female standoffs (x2)
– M2.5x8 screws (x2)
– M2.5x6 screws (x4)
Preparing the Environment
Ensure that the environment you are using the ATCA-3671 in meets the following
specifications.
Ambient temperature range
(IEC 60068-2-1, IEC 60068-2-2)
0 °C to 40 °C
Operating temperature range
Used with a Single-Module ATCA
Chassis
0 °C to 25 °C
Used with a 14-Slot ATCA Chassis Dependent on final system installation
Note Operating temperatures are valid only when the ATCA-3671 module is used
with the specified chassis.
Operating humidity (IEC 60068-2-56) 10% to 90% RH, noncondensing
Pollution Degree 2
Maximum altitude 2,000 m at 25 °C ambient temperature
Indoor use only.
Caution Electrostatic Discharge (ESD) can damage the AIO-3681/3682 and
AIO-3691. To prevent damage, use industry-standard ESD prevention measures
during installation, maintenance, and operation.
Installing the Software
You must be an Administrator to install NI software on your computer.
1. Install an ADE, such as LabVIEW.
2. If you chose to install LabVIEW in step 1, install LabVIEW FPGA.
3. Visit ni.com/info and enter the Info Code atcadriver to access the driver download
page for the latest NI ATCA FPGA Modules software.
4. Download the NI ATCA FPGA Modules driver software.
2Included in some ATCA-3671 kits.
ATCA-3671 Getting Started Guide | © National Instruments | 5

5. Follow the instructions in the installation prompts.
Note Windows users may see access and security messages during
installation. Accept the prompts to complete the installation.
6. When the installer completes, select Restart in the dialog box that prompts you to restart,
shut down, or restart later.
Installing the Hardware
Protection Impairment
Caution You can impair the protection provided by the ATCA-3671 if you use it in
a manner not described in this document.
Caution Do not operate the ATCA-3671 in a manner not specified in this
document. Product misuse can result in a hazard. You can compromise the safety
protection built into the product if the product is damaged in any way. If the product
is damaged, return it to NI for repair.
Caution Observe all instructions and cautions in the user documentation. Using
the model in a manner not specified can damage the model and compromise the
built-in safety protection. Return damaged models to NI for repair.
Installing the RTM
Caution Install the RTM before installing the ATCA-3671. Installing the
ATCA-3671 before installing the RTM can damage the connectors of both modules.
1. Gently guide the module into the chassis module guides and slide the module into the
chassis until it is fully inserted.
2. Close the module ejector handles to fully seat the module and latch it to the chassis, as
shown in the following figure.
Figure 1. Using the Ejector Handles to Install the RTM
3. Tighten the four captive screws on the panel to secure the module.
6| ni.com | ATCA-3671 Getting Started Guide

Installing the ATCA-3671 Module
Caution Install the RTM before installing the ATCA-3671. Installing the
ATCA-3671 before installing the RTM can damage the connectors of both modules.
1. Ensure that the module ejector handles are in the open position, as shown in the following
figure.
Figure 2. Opening the Module Ejector Handles
ESD
SENSITIVE
ATCA-3671
FPGA Module for ATCA
AIO A AIO B AIO C AIO D
JC OUT A CLK IN/OUT A JC OUT B CLK IN/OUT B
1Gb ETH
GPIO BAIO CLK JTAGSYNC A GPIO C MGT REF SYNC B GPIO DGPIO A
JC OUT C CLK IN/OUT C JC OUT D CLK IN/OUT D
2. Gently guide the module into the chassis module guides and slide the module into the
chassis until it is fully inserted.
3. Close the module ejector handles to fully seat the module and latch it to the chassis, as
shown in the following figure.
Figure 3. Closing the Module Ejector Handles
ESD
SENSITIVE
ATCA-3671
FPGA Module for ATCA
AIO A AIO B AIO C AIO D
JC OUT A CLK IN/OUT A JC OUT B CLK IN/OUT B
1Gb ETH
GPIO BAIO CLK JTAGSYNC A GPIO C MGT REF SYNC B GPIO DGPIO A
JC OUT C CLK IN/OUT C JC OUT D CLK IN/OUT D
4. Tighten the four captive screws on the panel to secure the module.
Installing AIO-3681/3682 Modules
Install one or more AIO-3681/3682 modules to enable analog-to-digital and digital-to-analog
conversion of RF signals.
Determine how many modules you are installing and choose the appropriate number of empty
slot(s) in the ATCA-3671. If hardware is present in the slot(s) you choose, remove the installed
ATCA I/O module(s), riser card(s), and additional components from the slot(s).
Ensure you have the following components for each AIO-3681/3682 module:
ATCA-3671 Getting Started Guide | © National Instruments | 7

• Riser card (x1)
• Male-to-female M2.5 standoffs (10 mm hex length, 6 mm thread length) (x2)
• Male-to-female M2.5 standoffs (12.5 mm hex length, 3.5 mm thread length) (x2)
• M2.5x8 screws (x2)
• M2.5x6 screws (x2)
Complete the following steps to install one to four AIO-3681/3682 modules, depending on
your chosen hardware configuration.
1. Install a riser card into the ATCA-3671 motherboard mating connector. Secure with two
male-to-female M2.5 standoffs (10 mm hex length, 6 mm thread length), as shown in the
following figure.
Figure 4. Installing Riser Card(s)
FPGA Module for ATCA
ATCA-3671
1
3
2
1. ATCA-3671 Module
2. Riser Cards
3. Male-to-Female M2.5 Standoff (10 mm Hex Length, 6 mm Thread Length)
8| ni.com | ATCA-3671 Getting Started Guide

2. Install two male-to-female standoffs into the AIO-3681/3682 module with two male-to-
female M2.5 standoffs (12.5 mm hex length, 3.5 mm thread length), as shown in the
following figure.
Figure 5. Installing Standoffs into the AIO-3681/3682 Module(s)
2
1
3
1. AIO-3681/3682 Module
2. M2.5x6 Screw, Preinstalled
3. Male-to-Female M2.5 Standoff (12.5 mm Hex Length, 3.5 mm Thread Length)
3. Align the AIO-3681/3682 module with the riser card connector and gently mate the
connectors, as shown in the following figure.
Note The AIO-3681/3682 module must be centered on the riser card
connector so that the holes for the screws are aligned.
ATCA-3671 Getting Started Guide | © National Instruments | 9

Figure 6. Aligning the AIO-3681/3682 Module(s) with the Riser Card(s)
FPGA Module for ATCA
ATCA-3671
2
1
3
1. ATCA-3671 Module
2. Riser Card
3. AIO-3681/3682 Modules
4. Secure the AIO-3681/3682 module to the ATCA-3671 module with two M2.5x8 screws
from the underside of the ATCA-3671 module, as shown in the following figure.
10 | ni.com | ATCA-3671 Getting Started Guide