Nav TV StreamStick User manual

StreamStick by NAV-TV is a USB-powered, HI-FI
Bluetooth 4.0 audio streaming module for automotive
and home use. Make ANY stereo (equipped with AUX
input) a Bluetooth-audio receiver!

Using the StreamStick is easy!
1. Choose one of the provided cables that works best with your application and connect it to
the 3.5mm port on the side. Connect the other end to the AUX-Input on your stereo. Make sure
‘AUX’ is selected as the source on the stereo.
2. Connect the StreamStick to practically any USB port you can nd (vehicle dashboard, back
of TV, receiver or stand-alone USB charger). A blue LED will blink slowly when properly
powered.
3. On your source device (cell phone, tablet) turn on Bluetooth in settings and select ‘Search
for Devices’
4. ‘StreamStick-xxxx’ should appear within a few seconds, connect and pair (BT icon should
become bold when connected). The built-in LED will light up solid when a device is connected
and ready to stream.
5. That’s it! Start some music from your source device for Hi-Fidelity enjoyment!

The StreamStick will
remember up to 8 devices.
After 8 devices have been
stored, the rst (original)
device paired will be
forgotten.
Once a device is stored,
the StreamStick will
auto-pair with most
devices. This process may
take up to 1 minute.
Try to avoid placing the
StreamStick behind dense
objects, if possible – while
line-of-sight isn’t necessary
for Bluetooth applications,
you will get best results if
the StreamStick is not
blocked.
Connect the StreamStick to practically any USB port you
can nd (vehicle dashboard, back of TV, receiver or
stand-alone USB charger). A blue LED will blink slowly
when properly powered.
Choose one of the provided cables that works best with your
application and connect it to the 3.5mm port on the side.
Connect the other end to the AUX-Input on your stereo. Make
sure ‘AUX’ is selected as the source on the stereo.
The ‘PAIR’ button is only used if the user wants to disconnect
the currently connected device and pair a dierent one. Press
the button once, return to the next source device and make
sure it is searching via Bluetooth – if the device is stored in the
StreamStick it will connect and pair automatically.

3950 NW 120th Ave,
Coral Springs, FL 33065
USA/CAN TEL : [phone]
INT TEL: [phone]
www.navtv.com
[e-mail]
[e-mail]
Technical Specications:
- Bluetooth 4.0 Class 2
- 3Mbps max data rate
- Operating Range: 20-30m
- DAC: 16 bit
- DAC SNR: 96 dB
- Supply Voltage: 5V DC
- Typical Current (streaming): 40mA max
- Typical Current (idle): 21mA max

Contains FCC ID: SSSBC127-X
RoHS Compliant
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment
into an outlet on a circuit dierent from that to which the receiver is connected; Consult the dealer or an experienced radio/TV
technician for help.
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more
should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer
than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante