NavePoint 6U User manual
M6 NutM5 Screw M3.5 ScrewM6 Screw
H-1 H-2 H-3 H-4
Cabinet
Size
6U 9U 12U 15U 18U
M6 Screw 28 28 28 32 32
M6 Nut 4 4 4 4 4
M5 Screw 18 18 18 18 18
M3.5 Screw 10 10 10 10 10
Tools needed: allen wrench (wrench included) and phillips screw driver.
Extra cage nut set for accessories included .
Rev. 20170517
Important information-
Keep this information for further reference.
WARNING
Different wall materials require different type of
anchoring devices. Use anchoring devices suitable
for the walls which you are using in your applica-
tion. For advice on suitable anchoring systems,
contact your local specialist.
Limitations of Liability: In no event will NavePoint, LLC. (or its
ofcers, directors, employees or agents) be liable for any dam-
ages, whether direct or indirect, special, punitive, incidental or
consequential damages (including, but not limited to, lost prots
or revenue, loss of use, lost business opportunities or loss of
goodwill) or for the costs of procuring substitute products, arising
out of or in connection with the use of the product, whether such
liability arises from any claim based upon contract, warranty, tort
(including negligence), product liability or otherwise, whether
or not seller has been advised of the possibility of such loss or
damage. In no event will seller’s total cumulative liability, from
all causes of action and all theories of liability, exceed the total
amounts actually paid to seller by customer under the order that
gives rise to any liability hereunder.
The information contained in this document is subject to change
without notice.
NavePoint makes no warranty of any kind with regard to this
material, including, but not limited to the implied warranties of
merchantability and tness for a particular purpose.
NavePoint shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
NavePoint assumes no responsibility for the use, application, or
reliability of the software or hardware that you install into the
product. Always install the heaviest equipment in the bottom.
It is highly recommended that installation of this product be
performed by a qualied and experienced installer. Improper
installation of this product could result in damage to the
product, other equipment, or personal injury. NavePoint cannot
be held responsible for damage to equipment or personal
injury resulting from improper use, installation or the misuse of
information presented in this document.
Examine the package for any damaged or loose parts. If
anything is damaged or missing, contact NavePoint for
assistance. Do not attempt to install or use cabinet if it has
been damaged.
Thank you for purchasing a NavePoint product. NavePoint intends this manual to guide you through
a smooth installation of the product. NavePoint assumes that you are qualied in the servicing of
computer equipment and trained in recognizing any hazards that may occur in the installation of this
product. If you have any questions regarding the installation or use of your product, please call us at
888.505.1363.
1
M6
2
M5
3
M6
Start with a Side Frame (A) lay at with slotted
rails upright. Place Mounting Rail (C) at
desired depth. Secure it in place with M6
screws (H1) and M6 cage nuts (H4).
Repeat on other side frame.
Attach the four Horizontal Structure Bars
(D) to the Side Frames (A) using M5 screws
(H2).
Lay top cover (F-1) on top of the cabinet
frame and secure with M6 screws (H1).
Repeat steps to secure Bottom (F-2) to
cabinet frame.
Mount optional L Bracket (B) or other
shevling accessoire as desired height, using
M6 screws (H1) and M6 cage nuts (H4).
Repeat on other side frame.
F-1
F-2
D
D
A
C
L
A
B
H
F-1
D
I
C
E
F-2
G
Legend:
A
B
C
D
E
F-1
F-2
G
H
I
Side Frame
L Bracket
Mounting Rail
Horizontal Structure Bar
Side Panel
Top Cover
Bottom
Tempered Glass Door
Back Panel
Hanger Bar
*Although the depth of the optional bracket is not
permanent, it is recommended that you take this
time to ensure the space between mounting rails is
accurate to what your application requires.
*
4
M3.5
5
6
Attach Back Panel (H) to the rear of the
cabinet frame,using M3.5 screws (H3).
Click Side Panels (E) into place.
To install the Tempered Glass Door (G),
locate the side with two pins. Insert the
xed pin into door hinge hole. With your
thumb, pull down on the spring pin and
slide it into place over second door hinge
hole and release. The pin should click
into place, securing the door.
H
E
G
To install locks on the Side Panels (E) push out plastic plugs. Unscrew the latch and washer using a
phillips screwdriver and place to the side. Next unscrew the large hex washer and at washer and
place to the side. Push lock through door and then replace all parts on the door. Once all pieces of
the lock are secure, insert key and make sure the lock properly rotates. You may need to rotate the
hook to ensure it properly locks.
To install locks on the Tempered Glass Door (G), unscrew the latch and washer using a phillips
screwdriver and place to the side. Then unscrew the large hex washer and at washer and place to
the side. Push lock through door and then replace all parts on the door. Once all pieces of the lock
are secure, insert key and make sure the lock properly rotates. You may need to rotate the hook to
ensure it properly locks.
Screw with star washer
Washer
Latch
Hex Washer
Flat Washer
Lock Cylinder
Optional side panel lock
Spring Pin
Front Door Lock
12
M3.5
3
4
Wall Mounting
Secure Hanger Bar (I) to wall with
anchors and screws (not included).
Click Side Panels (E) into place.
Lift the cabinet up and slide
onto Hanger Bar (I) hooks.
Take two M3.5 screws (H3)
and secure the cabinet to the
hanger bar tightly.
To install the Tempered Glass Door (G),
locate the side with two pins. Insert the
xed pin into door hinge hole. With your
thumb, pull down on the spring pin and
slide it into place over second door hinge
hole and release. The pin should click into
place, securing the door.
It is recommended that the cabinet be mounted to the wall prior to the side panels and
door being installed
I
E
G
Other manuals for 6U
2
This manual suits for next models
4
Table of contents
Other NavePoint Enclosure manuals
