NavePoint Basic Series User manual

www.NavePoint.com
[email protected]
© 2017 NavePoint, LLC
Performance Series
Part Identier
Top Cover 1
Bottom Cover 2
Frames 3
Glass Door 4
Side Panels 5
Horizontal Rail 6
L Bracket 7
Rear Panel 8
Mounting Bracket 9
Vertical Rail 10
Rev. 20170517
Important information
Keep this information for further reference.
WARNING
Different wall materials require different type of
anchoring devices. Use anchoring devices suitable
for the walls which you are using in your application.
For advice on suitable anchoring systems, contact
your local specialist.
Limitations of Liability: In no event will NavePoint, LLC.
(or its ofcers, directors, employees or agents) be liable
for any damages, whether direct or indirect, special,
punitive, incidental or consequential damages (includ-
ing, but not limited to, lost prots or revenue, loss of use,
lost business opportunities or loss of goodwill) or for
the costs of procuring substitute products, arising out
of or in connection with the use of the product, whether
such liability arises from any claim based upon contract,
warranty, tort (including negligence), product liability
or otherwise, whether or not seller has been advised of
the possibility of such loss or damage. In no event will
seller’s total cumulative liability, from all causes of action
and all theories of liability, exceed the total amounts
actually paid to seller by customer under the order that
gives rise to any liability hereunder.
The information contained in this document is subject to change
without notice.
NavePoint makes no warranty of any kind with regard to this
material, including, but not limited to the implied warranties of
merchantability and tness for a particular purpose.
NavePoint shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
NavePoint assumes no responsibility for the use, application, or
reliability of the software or hardware that you install into the
product. Always install the heaviest equipment in the bottom.
It is highly recommended that installation of this product be
performed by a qualied and experienced installer. Improper
installation of this product could result in damage to the
product, other equipment, or personal injury. NavePoint cannot
be held responsible for damage to equipment or personal
injury resulting from improper use, installation or the misuse of
information presented in this document.
Examine the package for any damaged or loose parts. If
anything is damaged or missing, contact NavePoint for
assistance. Do not attempt to install or use cabinet if it has
been damaged.
Thank you for purchasing a NavePoint product. NavePoint intends this manual to guide you through
a smooth installation of the product. NavePoint assumes that you are qualied in the servicing of
computer equipment and trained in recognizing any hazards that may occur in the installation of this
product. If you have any questions regarding the installation or use of your product, please call us at
888.505.1363.

M6
1Lay Bottom Cover (2) on the oor and insert
front and rear frames (3) into Bottom Panel.
Lay Horizontal Rails (6) on frames so one of
each end of rail sits on top of both frames. Use
Hex screws (E) and Hex Nuts (F) to secure parts
together.
*Ground wire may have to be replaced near
grounding copper screw.
Repeat for top.
2Assemble Vertical Rails (10) into Horizontal
Rails (6) using Cage Set M6 Screw with Cage
Set plastic washer and M6 Cage Nut (B) after
choosing depth for shelving.
3Assemble L Brackets (7) into Vertical
Rails (10) using Cage Set M6 Screw
with Cage Set plastic washer and M6
Cage Nut (B).
Model options may include:
Tools needed: Allen Wrench (included) and Phillips screwdriver
- Side Panel locks with keys
- Caster Wheels
B
E
F
D
C
A

4
M3.5
5
6
Attach Back Panel (8) to the rear of the cabinet
frame,using M3.5 screws (C).
Click Side Panels (5) into place.
To install the Tempered Glass Door (4), locate the side
with two pins. Insert the xed pin into door hinge hole.
With your thumb, pull down on the spring pin and slide
it into place over second door hinge hole and release.
The pin should click into place, securing the door.
H
5
4
Attach Casters with M6 screws (A) to bottom of the cabinet.
Secure Punch Out Covers with M4 (D) Screws.
7
8
Punch out cover

Side Panel
Front Door
To install locks on the Side Panels (E) push out plastic plugs. Unscrew the latch and washer using a
Phillips screwdriver and place to the side. Next unscrew the large hex washer and at washer and
place to the side. Push lock through door and then replace all parts on the door. Once all pieces of
the lock are secure, insert key and make sure the lock properly rotates. You may need to rotate the
hook to ensure it properly locks.
To install locks on the Tempered Glass Door (G), unscrew the latch and washer using a Phillips
screwdriver and place to the side. Then unscrew the large hex washer and at washer and place to
the side. Push lock through door and then replace all parts on the door. Once all pieces of the lock
are secure, insert key and make sure the lock properly rotates. You may need to rotate the hook to
ensure it properly locks.
Screw with star washer
Washer
Latch
Hex Washer
Flat Washer
Lock Cylinder
Optional side panel lock
Spring Pin
White Spacer

1
2
M3.5
3
4
Secure Hanger Bar (9) to wall
with anchors and screws (not
included).
Lift the cabinet up and slide
onto Hanger Bar (9) hooks.
Take two M3.5 screws (C)
and secure the cabinet to the
hanger bar tightly.
To install the Tempered Glass Door (4),
locate the side with two pins. Insert the
xed pin into door hinge hole. With your
thumb, pull down on the spring pin and
slide it into place over second door hinge
hole and release. The pin should click
into place, securing the door.
9
5
4
Click Side Panels (5) into
Mounting Instructions