NavePoint Consumer Series User manual

V3.0
OWNER’S MANUAL: Consumer Series Wallmount Cabinet
Keep this information for further reference.
Thank you for purchasing a NavePoint product.
Please examine the product for any damaged parts. If any part is damaged or missing, contact NavePoint for assistance. Do not attempt to install or
use product if it has been damaged. This product contains small items that could be a choking hazard – keep these items away from children.
During installation, lay product contents on cardboard or other protective surface to avoid any damage.
Do not use with equipment that is heavier than the indicated weight capacity for this product. This product is designed to be installed indoors on
wood stud walls, solid concrete walls or brick walls. Make sure that the supporting surface will safely support the weight of the equipment and all
attached hardware and components. It is recommended that installation be performed by a qualified installer. NavePoint cannot be held
responsible for damage to equipment or personal injury resulting from improper use or installation of product.
Maintenance: Check that the product is secure and safe to use at regular intervals (at least every three months).
Limitations of Liability: In no event will NavePoint, LLC. be liable for any damages, whether direct or indirect, special, punitive, incidental or
consequential damages (including, but not limited to, lost profits or revenue, loss of use, lost business opportunities or loss of goodwill) or for the
costs of procuring substitute products, arising out of or in connection with the use of the product, whether such liability arises from any claim
based upon contract, warranty, tort (including negligence), product liability or otherwise, whether or not seller has been advised of the possibility
of such loss or damage. In no event will seller’s total cumulative liability, from all causes of action and all theories of liability, exceed the total
amounts actually paid to seller by customer under the order that gives rise to any liability hereunder.

www.NavePoint.com 2 [email protected]
1. Parts Identification
(I) (J) (K) (L) (M)
M6 Hex Head Screws (16) M5 Screws (8) M5 Nuts (8) M6 Mounting Screws (10) M6 Cage Nuts (10)
(Black) (Black) (Black) (Silver) (Silver)
(N) (O) (P) (Q)
Side Panel Latches (4) Side Panel Locks (2) Front Door Lock (1) Hex Wrench (1)

www.NavePoint.com 3 [email protected]
2. Cabinet Assembly
STEP 1. Attach 2 Punch Out Covers (H) to the
Top Cover (B) and 2 Punch Out Covers (H) to
the Bottom Base (A).
STEP 2. Insert the Front Rack Frame (C) and the
Back Cover (D) into the Bottom Base (A).
Secure with 8 black M6 Hex Head Screws (I)
using the Hex Wrench (Q).
STEP 3. Place the Top Cover (B) onto the Front
Rack Frame (C) and the Back Cover(D). Secure
with 8 black M6 Hex Head Screws (I) using the
Hex Wrench(Q).
Detail A
STEP 4. Install the 4 Vertical Rack Rails (G) into place at the desired depth using 2 black M5 Screws (J) and 2
black M5 Nuts (K) for each Rack Rail (G). When determining the appropriate depth, be sure to consider the
equipment that you plan to mount inside the enclosure.
Note: Be sure that the rail depth is the same on both sides of the cabinet.

www.NavePoint.com 4 [email protected]
A
B
STEP 5. Install the Side Panel Latches (N) and the Side Panel Locks (O) on the two Side Panels (F) as shown in
Diagram A.
STEP 6. Install the two Side Panels (F) into place using the Side Panel Latches (N) as shown in Diagram B.
Once each Side Panel (F) is attached, test to ensure that each Side Panel Lock (O) locks properly.
C
D

www.NavePoint.com 5 [email protected]
3. Mounting the Cabinet to the wall
Attach the cabinet to a wall or other
suitable mounting surface. Mounting
holes are spaced 16" as reflected in
the diagram.
Warning: Do not attempt to mount to
wall, when equipment is mounted
inside cabinet. The cabinet can hold up
to 110 pounds evenly distributed.
Make sure wall surface can hold weight
of the cabinet and equipment.
STEP 7. Install the Front Door Lock (P) on the Front Glass Door (E) as shown in diagram C.
STEP 8. To attach the Front Glass Door (E) to the cabinet, locate the side with the two pins. Insert the
bottom fixed pin into the door hinge hole. With your thumb, pull down on the top spring pin and slide it into
place over the second door hinge hole and release. NOTE: Each side of the front of the cabinet has door
hinge holes; this allows you to choose the door swing orientation.

www.NavePoint.com 6 [email protected]
4. Equipment Installation
1 Rack Unit
-Squared Hole Mounting
1 Locate the numbered square openings in the Vertical Rack Rails (G) where you plan to install your equipment.
Install silver M6 Cage Nuts (M) into the square openings to provide an attachment point for the M6 Mounting
Screws (L) . Note: Consult your equipment documentation to determine how many cage nuts will be required
and where they will need to be installed.
a- From the inside of the Vertical Mounting Rails (G), insert one of the flanges of the cage nut through the
square opening. Press it against the side of the square opening.
b- Compress the cage nut at the sides slightly to allow the remaining flange to fit through the square opening.
When the cage nut is properly installed, both flanges will protrude through the square opening and will be
visible on the outer surface of the mounting rail. Repeat steps 1a and 1b until all required cage nuts are
installed.
2 After installing the required cage nuts, use the included silver M6 Mounting Screws (L) to secure your
equipment into the installed M6 Cage Nuts (M).