SnapSafe Super Titan XXL User manual

Super Titan XXL Owner’s Manual

Thank you for purchasing a SnapSafe Super Titan XXL. The
SnapSafe Kwik-Lock™Modular Assembly System offers all
the impregnability of a welded safe in an easy-to-assemble
modular design. Now, you have the peace-of-mind knowing
your valuables are protected from loss due to re or theft.
Best of all, you can easily locate and relocate this protection
anywhere, piece-by-piece, to any room, in minutes.
1
SNAPSAFE SUPER TITAN XXL
SPECIFICATIONS:
MODEL : Super Titan XXL
EXTERIOR : 59”H x 46”W x 30”D
(add 3” for handle)
INTERIOR : 53 3/4”H x 41”W x 26 1/5”D
DOOR OPENING : 52”H x 14 ¾”W
LOCKING BOLTS : 8
CAPACITY : 56 + Long Guns
WEIGHT : 810 lb.
CUSTOMER SERVICE
For all Customer Service questions call toll free:
1-877-214-4470 fax: [phone]
Or write: SnapSafe Inc. Customer Service
3721 Doubleton Drive Stuart, FL 34997
Or Email: [email protected]
Side Front
(17”)
Top and Bottom
(40”)
24”
38”
24”
38”
SNAPSAFE
SUPER TITAN XXL
FEATURES:
• Delivered right to your door
• Assembles in minutes without tools
• Kwik-Lock™ Modular Assembly
System
• Sledgehammer and pry-bar
resistant 3/16” solid steel door
• Thick steel exterior walls
• 2300°F one-hour Fire Shield
protection
• Heat activated door re seals
• 30 slot full gun rack
• Secures 56+ long guns
• Option Between UL Security Listed
locks: Digital or Mechanical
• Eight ¾” chrome steel live
locking bolts
• Spring-loaded relocker
• Powder coated nish
• Lined interior
• Adjustable lined shelves
• Includes 1 full shelf and full
gun rack and a half gun rack
with 2 half shelves
• Professional grade “non breach
seal” dead bolt door
• Predrilled for oor mounting
• Lifetime warranty
46”
30”
30” 46”

23
ASSEMBLING YOUR SUPER TITAN XXL
1. Unpack and lay out all parts.
2. Thread DOOR HANDLE SPOKES (Part #11) onto the hub on DOOR (Part #12).
3. Install a fresh high-quality 9V battery in the Entry Keypad. (See pgs 8 and 9).
4. Important – Remove temporary door hinge bolts from door hinges.
5. Enter the factory combination code and open the DOOR, then lift it off the
DOOR FRAME (Part #6) and set aside.
6. Assemble Top, Bottom and Sides (Parts #1 through #4) rst. Then Kwik-Lock the entire
assembly onto the BACK (Part #5).
7. For additional help watch our “Live Action Assembly Video” on the “Features”
page at www.snapsafe.com.
Notes:
1. Each part is marked with an assembly number, orientation and instructions.
2. Each part’s orientation e.g. TOP, BOTTOM, FRONT, etc. matches its orientation in
the assembled vault. LEFT and RIGHT are as you face the front of the vault.
3. For easier assembly of the Kwik-Locks, remove the FIRESHIELD blankets from the TOP,
BOTTOM and SIDEWALLS. Stuff them back into place before interior assembly.
4.Screw on Kwik-Locks loosely at rst. Once all Exterior Panels are aligned and seated,
tighten the Kwik-Locks. Tightening with a tool is NOT necessary.
5.The INTERIOR SIDE PANELS are designed to t snuggly. Insert them through the
door opening bottom-to-top and then slide into nal position front-to-back.
6. Insert the INTERIOR BOTTOM PANEL through the door opening between the front
and back shelf strips and then drop into position front-to-back.
BOLTING DOWN YOUR VAULT
We recommend bolting your vault to the oor using two ¼” wedge anchor
concrete bolts through the predrilled holes in the BOTTOM of the vault.
DOUBLE SAFEGUARDING VALUABLE PAPERS
Your SnapSafe Super Titan XL’s Fire Shield protection is rated at 2300ºF for
one-hour. However, we recommend that if you are going to be putting important
papers in the vault, you rst put it in a re resistant document box, and then put
it in the vault.
YOUR COMBINATION CODE
• Your factory preset combination code is 1-2-3-4-5-6.
• It is recorded in a small envelope wired to the door handle of your vault.
Store this combination in a location other than your vault.
#5
#2
#3
#12
#1
#6
#4
Part #1 – LEFT SIDE
Part #2 – TOP
Part #3 – RIGHT SIDE
Part #4 – BOTTOM
Part #5 – BACK
Part #6 – DOOR FRAME
Part #7 – TOP INTERIOR PANEL*
Part #8 – LEFT INTERIOR PANEL*
Part #9 – RIGHT INTERIOR PANEL*
Part #10 – BOTTOM INTERIOR PANEL*
Part #11 – DOOR HANDLE SPOKES
Part #12 – DOOR
Part #15 – SHELF HARDWARE *
Part #18 – UPPER SHELF*
Part #19 – KWIK-LOCK HARDWARE*
Part #20 – GUN RACK*
Parts followed by an * are not shown
OPENING AND CLOSING
Opening:
1. Enter the 6-digit combination code.
2. Rotate 3-spoke handle clockwise into the open position and pull door open.
3. The Entry Keypad relocks in 4 seconds after a valid code has been entered.
4. The Entry Keypad will return to “standby” status with a long beep sound
if there is no operation in 10 seconds after the system has been activated.
5. If you enter an incorrect combination 4-times in a row, the lock will shut
down for 5-minutes.
Closing:
1. Close vault door.
2. Rotate 3-spoke handle counter-clockwise to the
closed position until you hear bolts engage.

45
LOW BATTERY ALERT
Your lock has a “Low Battery Alert.” If the Entry Keypad beeps repeatedly
during an unlocking, the battery is low and needs immediate replacement.
CARE AND MAINTENANCE
With a little care and maintenance your SnapSafe Modular Vault will last
a lifetime. Keep the door hinge pins lightly greased so that the door opens
smoothly. Vacuum the inside from time to time, and wipe down the outside
with a soft cloth and mild detergent. Never use harsh solvents or abrasives
on any surfaces, as they may damage the exterior nish or interior
materials.
SNAPSAFE LIFETIME WARRANTY
Were going to take care of you.
Period.
We have built products and a company we are proud of and want you to be
as well.
If you ever experience a re or attempted break-in we’ll repair or replace
your vault at no charge. (All you have to do is to forward the report from
the proper investigative agency)
INSTALLING AND REPLACING ENTRY KEYPAD BATTERY
Your vault is equipped with an electronic lock made with non-volatile memory,
meaning your combination code is retained even if the batteries are no longer
powering the lock. If this happens, simply replace the batteries.
Install only a high-quality alkaline battery in the compartment in the back of the
Entry Keypad following these steps.
1. Remove Entry Keypad. Slide it up
and carefully pull it away from the
vault door. (Fig.1)
Note: Do not pull the Keypad as too much
force may damage the cable.
2. Snap new battery into the connector
clip, and slide it into the battery
compartment top down so that the
wires will not be pinched between
the battery and the vault door. (Fig.2)
3. Fold the connection cable inside
the Keypad. (Fig.3)
4. Position the keypad over the
mounting screws, and slide it down
into position.
Note: Make sure the connection cable is not
trapped between the Keypad and the door
or rubs or tangles on the mounting screws.
(Fig.4)
CHANGING YOUR COMBINATION CODE
Write down and store a new 6-digit code (Do not store in vault).
You cannot set the combination code to six (6) zeros (0).
1. Open vault door and lock it in open position.
2. Enter zero (0) six (6) times. One beep sounds indicating the entry is valid and
the system is awaiting a code change.
3. Enter the existing 6-digit code. One beep sounds, indicating the entry is valid.
4. Enter a new 6-digit code. One beep sounds, indicating the entry is valid.
5. Re-enter the new 6-digit code. One beep sounds, indicating that the code in
step 4 and 5 are the same and that the code change is successful.
6. If three beeps sound, the code change was unsuccessful, and the existing
code is still valid. Repeat steps 2 – 5.
7. Enter and check new code 3-times before closing door.
Note: Each step in the code change process must be completed in 10 seconds or the system reverts back to
“standby” status.

IMPORTANT!
Keep for Your Records.
Do not store this booklet and information in your vault.
Date of receipt of safe__________________
Vault Serial number____________________
(Located on the plate in the lower right corner of the front of the vault)
Customer Service: 3721 Doubleton Drive Stuart, FL 34997
1-877-214-4470 Fax: [phone] Email: [email protected]