Naya PNI-RP2700 User manual

User’s manual of
indoor repeater
PNI-RP2700
Please keep the manual for reference

Content
1 Check the items in the package············································································3
2 Parts introduction································································································3
2.1 Front panel··································································································3
2.2 Back panel··································································································3
3 Basic operation···································································································4
4 Using instructions of single repeater networking·························································5
5 Using instructions of multi-repeaters networking·························································6
6 LAN networking diagram of multi-repeaters·······························································7
7 WAN networking diagram of multi-repeaters······························································8
8 Maintenance and cleaning·····················································································9
8.1 Maintenance·······························································································9
8.2 Cleaning·····································································································9
9 Quality commitment and maintenance terms······························································9
10 No-warranty policy····························································································10
11 Warranty card··································································································11
2

1 Check the items in the package
2 Parts introduction
2.1 Front panel
Item Q’tyNo.
①
1
1
1
②
③
④
1
Manual
Antenna
Adapter
Indoor repeater
◆The package contains the following items, if any damage or loss, please contact Naya or the
dealer you purchased from.
3
12V2A Adapter
Repeater
Antenna
① ② ③

2.2 Back panel
3 Basic operation
◆ Step 1: Install antenna, and turn it clockwise until tightened.
◆ Step 2: Plug in the 12V adapter to power it and wait for the RUN to light up.
◆ Step 3: Open the handheld and select the corresponding channel to start the call.
4
Item DescriptionNo.
①
RX indicator
RUN indicator
②
③
TX indicator
Flashes when the signal is received
Flashes after powering on the device
Flashes when the signal is transmitted
Item DescriptionNo.
①
COM interface
LAN port
②
③
Antenna interface
RS232 interface, to connect computer for configuration of repeater
To connect multi-repeaters via TCP/IP networking
SMA antenna interface
④Power interface 12V adapter interface, 12V power apply
① ② ③ ④

5
4 Using instructions of single repeater networking
Channel 84
Note: The channel layout in this manual is for the installation solution reference only.
◆ The default channel of the repeater in the single relay mode is 84, corresponding to the channel
84 of the handheld terminal. After the repeater is powered on, the handheld terminal switches to
the channel 84 for call, without any settings.
◆ The number of handheld terminals in single relay mode is unlimited, and up to 8 people can
speak at a time, which can be heard by other people.
◆If the repeater has wireless relay enabled, up to 4 people can speak at the same time.
Channel 84 Channel 84
Channel 84 Channel 84

Please read the manual carefully before using
Website: http://www.nayatec.com
Manufacturer: Shanghai Naya Intelligence Technology. Co.,Ltd.
Address: No.7001 Zhongchun RD., Shanghai, 201101, China Version:20220802

6
5 Using instructions of multi-repeaters networking
Note: The channel layout in this manual is for the installation solution reference only.
◆ In the multi-relay mode, please ask the dealers to pre-configure channels and networking
parameters of multiple repeaters, and then the configured multiple repeaters can be connected
through the network cable before powering on. At this time, the handheld terminal channel should
be adjusted to the correct channel according to the requirements of the dealer.
◆ After the above configuration is completed, the handheld terminal can be powered on to conduct
the conversation. All handheld terminals under different repeaters are interconnected.
◆ If one handheld terminal moves from coverage of one repeater to the coverage of another
repeater, its channel will automatically switch to the same channel of the repeater with a stronger
signal for call, without manual switching.
Channel 85 Channel 55
TCP/IP
Channel 55Channel 55Channel 85

7
6 LAN networking diagram of multi-repeaters
LAN proper connection diagram
LAN fault connection diagram
Router
Switch
PNI-HT2100
Base station Base station Base station
Channel 55 Channel 85 Channel 110
PNI-HT2100
Channel 55 Channel 85
PNI-HT2100
Channel 110
Switch
PNI-HT2100 PNI-HT2100
Base station
Channel 55
Base station
Channel 85
Base station
Channel 110
Router
Router
PNI-HT2100
Channel 55 Channel 85 Channel 110

8
Note: The channel layout in this manual is for the installation solution reference only.
◆ The port mapping function of the router is required for Wan connections. Mapping port number:
23457(please contact the professional network engineer for setting).
◆ The public IP address must be a fixed IP, and the dynamic IP address cannot be used normally.
◆ Channel adjustments: if using other single relay channels, please contact the reseller.
7 WAN networking diagram of multi-repeaters
Internet
Router
Router
Switch
Switch
Switch
Switch
Base station
Channel 55
Base station
Channel 85
Base station
Channel 95
Base station
Channel 110
PNI-HT2100
Channel 55
PNI-HT2100
Channel 85
PNI-HT2100
Channel 95
PNI-HT2100
Channel 110
Base station

9
IP67
0.25W
-20°C-60°C
FSK/GFS
wDR-8
12V
Product parameters
Product parameters
Working temperature
Output power
Modulation type
Working voltage
Working style
In order to ensure the good performance of this device and prolong its service life, please
be familiar with the following contents for better maintenance and cleaning.
8.1 Maintenance
◆ Do not puncture or scratch the device with hard objects.
◆ Do not store the device in an environment that contains corrosive electronic circuits.
◆ Do not damage the antenna, the relevant marks of the product shall be kept clean and intact and
shall not be torn up.
8.2 Cleaning
◆ Please clean the device regularly, and use a clean and dry towel or brush to remove the dust on
the surface of the equipment.
◆ If the device casing is dirty, it can be cleaned with neutral detergent and non-woven fabric. Do
not use detergent, alcohol or spray which will damage the device, make sure the device is
completely dry, otherwise do not use it.
8 Maintenance and cleaning
Naya promises that defects in material or workmanship under normal operating and
maintenance conditions of all devices produced by our company, are covered by the
warranty service specified below from the date of purchase.
◆ Scope and duration of warranty: 12 months
◆ Warranty application
9 Quality commitment and maintenance terms