NCR 7403-K325 User manual

7403‐K325
NoHingeBaseCover
KitInstructions

IssueA

ii
Revision Record
Issue Date Remarks
ANov2008Firstissue
 
 

1
Introduction
ThiskitprovidesareplacementRearBaseCoverforthe7403thatsealsthehingearea
foramorepleasingcosmeticappearanceoftheunitwhenusingtheDisplayWall
Mountkit(7403‐K321)tolocatetheDisplayHeadremotely.
7403-K325 Components
26913
7403-K325


2
7403-K321 Components
26908
Wall Mount Bracket Strain Relief
497-0462353
Screw, 6-32 x 5/16, Phillips, Flat Hd
006-8611269
Wall Mount Bracket
497-0462352
Remote Display Cable (2.5 m)
497-0462914
Remote Display Base
497-0462754
Hole Plug, 1.75"
006-8614720



3
Installation Procedure
1. RemovetheFrontCover.
a. Insert the Security Key and turn it 90 degrees clockwise.
26124a
Security Key
Front Base Cover

b. Pivot the top of the Front Base Cover toward the front of the unit and remove it from
the terminal.
26032a 

4
2. RemovetheDisplayHeadfromtheBase.
a. ReleasetheDisplayCablefromtheCableGuides.
b. DisconnecttheDisplayCable(squeezethesidesoftheconnector).
c. LoosentheDisplaythumbscrews(2).
26464a
Display Cable
Thumbscrews
Cable Guides


5
d. DepresstheDisplayReleaseLatches(2)andslidetheDisplayHeadtowardthe
rearoftheterminaltodisengageitfromthechassis.
26151b
Display Latches


6
3. InstalltheWallMountBracketStrainReliefonthebackofthe7403(2screws).
26731
Wall Mount Bracket Strain Relief
Screw, 6-32 x 5/16, Phillips, Flat Hd

4. ConnecttheRemoteDisplayCabletothe7403andsecureitwiththeCableStrain
Relief.AftertighteningtheStrainReliefinserttheendofthestrapintotheslotin
thebracketsoitwillnotinterferewhentheterminalismountedontheWall
Bracket.
26734
Strain Relief
Insert the end of the Strain Relief strap into slot. 

7
5. SecuretheWallMountBrackettoaverticalsurfaceusinglagscrews(4).Usethe
bracketasatemplatetomarkthelocationoftheholesorusethedimensions
shownbelow.
Note: Makesureyouinstallthescrewsintothestudsorthatyouusehardwareof
similarstrength.
26411
45 mm
(1.8 in.)
204 mm
(8.0 in.)
258 mm
(10.2 in.)
102 mm
(4.0 in.)
178 mm
(7.0 in.)
7.1 mm
(0.28 in.)
Use 6.4 mm
(0.25 in) bolts.

Note: TheWallMountBracketalsohasstandardVESAmountingholesthatcanbe
usedtomountthe7403onvariousVESAmounts,suchasswingarms.


8
Note: TheWallMountBrackethasthesameholepatternasolderUniversal
MountBrackets(7402‐K562,7402‐K522,and7401‐K533).Thereforeifyouare
replacingaterminalthatismountedonaUniversalMountBracketthensimply
removethebracketandinstalltheWallMountBracketusingthesamescrewsand
mountingholes.
Note: Therecommendedviewingheightfortheterminalis1.2m(48in.)from
thefloor.
26408a
Remove the older Universal Mount Bracket
and use mount 7403-K321 using same screws
and holes.
7403-K321 Wall Mount Bracket


9
6. Hangthe7403ontheWallBracket
a. AligntheterminalsotheextensionsontheWallBracketcanbeinsertedinto
theopeningsonthebackoftheterminal.
b. Securetheterminalbymovingitdownwardontothebracketextensions.
c. Locktheassemblyinpositionbytighteningthethumbscrews(2).
26437
Rear View
Thumbscrews


10
7. RemovetheNoCustomerDisplayCover(2screws).
26917a
No Customer Display Cover

8. RemovetheRearBaseCover(2screws).
26921
Rear Base Cover


11
9. RemovetheDisplayHingeAssembly(4screws).
26918
Display Hinge Assembly
Integrated Display Cable

10. DisconnectandremovetheIntegratedDisplayCable.

12
11. Installthe7403‐K325RearBaseCoverandsecureitwithscrews(2).
12. InstalltheFrontBaseCoverandsecureitbylockingtheSecurityKey.
26923
Rear Base Cover
Front Base Cover


13
13. Placethe7403Baseinthedesiredinstallationlocation.
14. ConnecttheRemoteDisplayCabletothe7403ElectronicsAssembly.
15. InstalltheRemoteDisplayBase(2captivescrewsinbase,2screwsinfromthe
rearoftheunit).
16. InserttheHolePlugintothetopoftheRemoteDisplayBase.
26910a
Remote Display Cable
Remote Display Base
Hole Plug

