NEC SV8500 User guide

FP85-104 S1
PCPro Setup Manual
NWA-041691-001
ISSUE 1.0

LIABILITY DISCLAIMER
NEC Infrontia Corporation reserves the right to change the specifica-
tions, functions, or features, at any time, without notice.
NEC Infrontia Corporation has prepared this document for use by its
employees and customers. The information contained herein is the
property of NEC Infrontia Corporation, and shall not be reproduced
without prior written approval from NEC Infrontia Corporation.
All brand names and product names on this document are trade-
marks or registered trademarks of their respective companies.
Copyright 2008
NEC Infrontia Corporation

PL- 1
PRODUCT LIABILITY
PRODUCT LIABILITY
1. USING THE EQUIPMENT SAFELY
The following safety information describes how to avoid injuries while working with the equipment and how to
prevent damage to the equipment. Learn the meaning of the following symbols and then read this section
carefully before using the equipment.
SYMBOL DESCRIPTION
DANGER
Incorrect use of the equipment may cause personal injury or death.
WARNING
Incorrect use of the equipment may cause personal injury or a serious
system fault.
ATTENTION
Incorrect use of the equipment may limit the system performance or
cause the system to fail.
The telephone system can only be used in NEC-designated countries.
If a system-down, malfunction, defect or external factor such as an electrical failure indirectly causes a loss of profit, the
company (or affiliates) will not be held responsible.
The goal is to produce a comprehensive and accurate manual. However, if errors or omissions are found in this manual,
please notify NEC Infrontia Corporation.
If the system requires installation or repair, contact the dealer or its service technician.
Carefully read all the manuals that relate to the system.

PL- 2
PRODUCT LIABILITY
2. SAFETY CONSIDERATIONS
2.1 PBX, Power-related Equipment and Peripheral Equipment
The following describes the safety considerations that must be observed before using the PBX, the power-
related equipment and the peripheral equipment, such as consoles, the Main Distribution Frame (MDF), the
Digital Remote Unit/Distributed Access Unit (DRU/DAU), telephones, PCs, printers, etc.
DANGER
If the system emits smoke or a burning, acrid odor, immediately turn off the system power.
Operating the system in this state might cause a fire, an electrical shock, or a system failure. After
turning off the power and confirming that the smoke has disappeared, contact the dealer.
If any equipment, such as the PBX, the main power source, a cabinet or peripheral equipment tips
over, turn off the power and contact the dealer.
If liquid reaches the inside of the PBX or the main power source, turn off the power. Operating the
system in this state might cause a fire, an electrical shock, or a system failure.
Do not touch the internal parts of the main power source to disassemble or configure it. This action
may cause a fire, an electrical shock or a system failure.
NEC Infrontia Corporation does not take any responsibility for disassembled or reconfigured
equipment.
Do not put any container objects (such as a vase or a cup) on the main power source or any
peripheral equipment. It might cause a fire, an electrical shock or a system failure.
Do not tamper with, modify, forcefully bend, forcefully remove or twist an electrical cord or any
wiring to or from the PBX, the main power source or any peripheral equipment. It might cause a
fire, an electrical shock, or a system failure. If the wiring is damaged, contact the dealer.
Correctly insert all of the electrical plugs into the electrical outlets. Before inserting a plug into an
electrical outlet, ensure that there is no dust on the plug’s blades. If there is dust on a blade, it might
cause a fire.
Do not use power other than the power that was designated for the system when it was installed.
PWR
dust
PWR

PL- 3
PRODUCT LIABILITY
DANGER
Do not attempt to repair or move the main power source without assistance from the dealer.
Do not put any metal or combustible objects into a vent of the PBX, the main power source, or any
peripheral equipment. Operating the system in this state might cause a fire, an electrical shock, or
a system failure. If this occurs, turn off the power and contact the dealer.
Be careful when using any peripheral equipment’s Liquid Crystal Display (LCD). If the liquid
leaks, it can be harmful to the user and to the system.
Before connecting any non-NEC, customer-provided equipment, check with the supplier to ensure
that the equipment is compatible. If the supplier cannot confirm the compatibility, do not connect
the equipment. Connecting incompatible equipment might cause a fire or an electrical shock.
PWR
?

PL- 4
PRODUCT LIABILITY
WARNING
Do not place any object on the PBX or the main power source. If the object falls, it might cause
personal injury or damage to the equipment.
When removing a plug from an outlet, be sure to grip the plug, not the cord. Gripping the cord to
remove the plug could cause a fire or an electrical shock to occur.
If lightning causes a fault, contact the dealer.
Provide the appropriate temperature, humidity, and ventilation on an around-the-clock basis. For
example, at a height that is one meter (3.28 feet) above the floor, the temperature should be between
20° C and 25° C (68° F to 77° F) and the humidity should be approximately 50%.
Take appropriate anti-static measures so that the other end of the anti-static kit can be connected to
the metal part of the frame.
ATT ENTION
Contents
Static Sensitive
Handling
Precautions Required

PL- 5
PRODUCT LIABILITY
WARNING
Observe the following precautions when using any optional batteries:
• The PBX’s emergency back-up battery may be a rechargeable lead battery. Check the
emergency battery for an electrical failure.
• Battery acid (electrolyte) is extremely harmful to human skin and eyes. If battery acid
contacts skin, wash the affected area with soap and water. If battery acid contacts the eyes,
flush the eyes with water. In either event, seek medical attention. If there is battery acid on a
cloth, use water to wash the battery acid from the cloth.
• Do not intentionally short batteries. Do not put the battery near a fire or in a fire. Do not
disassemble the battery, drop it or knock it against another object.
• The battery’s life expectancy is affected by its environment. The normal battery life is
approximately three years. If the battery is used in an outdoor setting and is exposed to high
temperatures, its life expectancy drops to approximately one year.
• Perform periodic diagnostic tests and maintenance procedures on the emergency battery and
its terminals to ensure their readiness. If there is a power failure and the emergency battery is
not ready, then the PBX will not work. Additionally, a damaged or dead battery, or terminals
that need replacement might cause battery acid to leak, which might cause smoke or a fire.
The battery and terminals are periodic replacement parts (the cost is chargeable to the
customer). A service contract, with the supplier or service technician, to perform routine
maintenance for the battery is recommended.
Do not touch peripheral equipment with wet hands. Do not allow any liquid to touch any of the
peripheral equipment.
Do not touch the printer’s internal components when replacing disposables such as a cartridge or a
ribbon. Ensure that the printer is turned off and that it is not hot in order to prevent burns from any
accidental contact with the internal components.
Do not drop the peripheral equipment or knock it against another object. These actions might cause
an equipment failure.

PL- 6
PRODUCT LIABILITY
2.2 Installation Environment
Consider the following items before the installation.
2.2.1 Stability
2.2.2 Floor, Wall and Ceiling
ATTENTION
Do not use benzine, thinner or alcohol for cleaning. When removing dust and dirt, put diluted, mild
detergent on a cloth and then wring out the cloth. Remove the dust and dirt with the cloth and then
wipe the cleaned area with a dry cloth.
ATTENTION
Do not place any equipment in the following environments:
• Locations that are exposed to direct sunlight
• Locations where the moisture level exceeds the allowed level
• Locations where the equipment might be exposed to water, oil, and chemicals
• Locations with very low temperatures, such as in a walk-in cooler or freezer
• Locations that are exposed to Electromagnetic Interference (EMI) from devices such as
television sets and two-way radios
• Locations that receive illegal electric waves
The life expectancies of the PBX and the main power source will be shortened if placed in a location
that is affected by hydrogen sulfide or salt, such as a seaside area.
WARNING
Install the PBX with anchor bolts to prevent constant movement or vibration, such as from a nearby
motor or automatic door, and to resist catastrophic movement from natural disasters, such as an
earthquake. If the system moves or falls, an injury could occur.
WARNING
The wall and ceiling materials must be resistant to Electrostatic Discharge (ESD) and provide heat
insulation. Since the battery’s life expectancy depends on the ambient temperature, the room where
the battery is installed must be well ventilated and vented to the outside. Check the battery
specifications to determine if the battery can or cannot be installed near a motor or a power
transformer.
The floor material that is under and around the PBX must be resistant to ESD.
Thinner

PL- 7
PRODUCT LIABILITY
2.2.3 Windows
2.2.4 Fire Extinguisher
2.2.5 Safety Environment
2.2.6 Air Conditioning Facilities
ATTENTION
Keep all of the windows closed if the location is affected by dust, sea breeze or corrosive gas.
Curtains or blinds are necessary to avoid direct sunlight.
WARNING Place a fire extinguisher for electrical fires (such as a carbon-gas fire extinguisher or a halon-gas
fire extinguisher) near the system. It is recommended that the room also be equipped with an
automatic fire-detection system. In the event of smoke and fire, turn off the main power source and
the backup battery, then use the fire extinguisher to put out the fire while trying to avoid inhaling
any smoke.
WARNING Consider measures to deal with disasters (such as fires, floods and earthquakes) and to ensure the
safety of the staff.
Regularly clean the room or rooms where the switching equipment resides.
Do not spray any insecticides directly on the equipment (insecticides can adversely affect the
switching equipment).
WARNING
The PBX and the air conditioning system must be installed separately and have separate power
sources.
To prevent an electromagnetic arc from causing noise, attach a surge-limiting capacitor and resistor
on the air conditioner’s electromagnetic switch’s coil.
It might be necessary to adjust the ventilation so the air conditioning is equally effective throughout
the equipment room.
Do not place the PBX in a location where condensation might fall from an air conditioner or a duct.
Do not place the PBX in a location where hot and humid air is exhausted, as this might damage the
PBX.

PRODUCT LIABILITY
PL- 8
2.2.7 Lightning Strikes
2.3 Disposables and Periodic-replacement Parts
WARNING
The grounding system must protect the PBX, MDF, main power source, MAT, printer, modems, etc.
from damage caused by lightning strikes and electrical surges.
All the grounding conductors must have a resistance of less than one Ωto bring a zero-voltage
reference to the system components.
To achieve this, the following ground conductors must connect to the Primary Ground Bar:
• The Earth Ground (E) from the Rectifier
• The Frame Ground (FE) from the PBX
• The Power Ground (PE) from the PBX, through the Rectifier
• The Frame Ground (FE) from the MDF
• The AC service outlets, with AC 100 V plug outlets, for the MAT, printer, modems and any
measurement devices, such as a protocol analyzer.
ATTENTION
Many parts, such as fans, batteries, backup batteries, hard disks, fuses and displays need to be
replaced on a periodic basis. In the event of sudden traffic, a part that is past due for replacement
might lead to a system failure and damage to the PBX.
Replace the disposable items such as ink ribbons, printer cartridges, floppy disks, recording paper
and headsets as needed.
A service contract with the dealer or its service technician to monitor the replacement cycles and to
supply the replacement parts and the necessary disposables is recommended.

TERMS-1
TERMS IN THIS MANUAL
System Name
In this manual, the following are used unless the types of the Telephony Server and the PBX need to be identified.
Note 1: UNIVERGE SV7000 Remote Node over IP is also included in the SV7000 series, which is migrated from
the existing IPX system. It is mentioned as “Remote Node over IP” or “the system” in this manual.
Note 2: In regard to China market, NEAX2400 IPX Internet Protocol eXchange has not been released but
NEAX2400 is released.
Note 3: In regard to China market, NEAX2000 IPS INTERNET PROTOCOL SERVER has not been released but
NEAX2000 is released.
TERMS USED IN THIS MANUAL SYSTEM NAMES
SV8500, the system UNIVERGE SV8500
SV7000, the system UNIVERGE SV7000 Note 1
MPS, SV7000 MPS, the system UNIVERGE SV7000 MPS
IPX, 2400 IPX, NEAX 2400 IPX, the system NEAX2400 IPX Internet Protocol eXchange Note 2
IPS, 2000 IPS, NEAX 2000 IPS NEAX2000 IPS INTERNET PROTOCOL SERVER Note 3
NEAX IMX, IMX NEAX2400 IMX
NEAX7400 IMX
NEAX7400 ICS (IMX)
NEAX IVS2, IVS2NEAX2000 IVS2
NEAX2000 INTEGRATED VOICE SERVER
NEAX7400 ICS M100MX
NEAX IVS, IVS NEAX7400 ICS Model110
NEAX7400 ICS Model120
NEAX7400 ICS Model80VS
NEAX7400 ICS Model100

TERMS-2
Terminal Name
In this manual, the following terminals are mentioned as each common term unless these types need to be identified.
Note 4: This terminal provides users with all features currently available on DtermIP (Proprietary Protocol).
GENERIC TERMS USED IN THIS MANUAL TERMINAL NAMES
Desktop
Terminal
Digital terminal
Dterm Dterm Series E/Dterm 75
Dterm Series i
DT300 Series DT310
DT330
IP
Station
IP terminal
IP Enabled
Dterm
Dterm Series E/Dterm 75
with IP adapter Note 4
Dterm Series i with IP
adapter Note 4
DtermIP INASET Note 4
DtermIP DtermIP
(Proprietary Protocol)
Soft Phone
Soft Phone (Propri-
etary Protocol)
DtermSP20
DtermSP30
DtermSP30
(Proprietary Protocol)
SIP
terminal
Soft Phone (SIP) DtermSP30 (SIP)
Soft Client SP350
SIP Multiple Line terminal
DtermIP DtermIP (SIP)
DT700 Series
DT710
DT730
DT750
WLAN Handset (MH Series) MH250
Standard SIP terminal Third-party SIP terminal
PS PHS
PCS

TERMS-3
Media Gateway (MG), Media Converter (MC), and Voice Conference Server (VS) Names
In this manual, the following are mentioned as each common term unless these types need to be identified.
GENERIC TERMS USED IN THIS MANUAL EQUIPMENT NAMES
MG(PRI)
MG(PRI) Card [SCA-24PRIA]
MG(PRI) Box [MG-24PRIA]
MG(PRI) Card [SCA-30PRIA]
MG(PRI) Box [MG-30PRIA]
MG-PRI/MG-PRA
MG-T1(SIP) MG-T1(SIP) Card [SCA-24DTIA]
MG(BRI)
MG(BRI) Card [SCA-2BRIA]
MG(BRI) Box [MG-2BRIA]
MG-BRI
MG(SIP)
MG-SIP16
MG-SIP16 Card [SCA-16SIPMGA]
MG-SIP16 Box [MG-16SIPMGA]
MC&MG-COT
MCMG Card [SCA-4LC2COTA]
MCMG Box [MG-4LC2COTA]
MCMG Card [SCA-7COTA]
MC&MG-COT with PFT
MG-COT
MG-COT Card [SCA-6COTA]
MG-COT Card [SCA-6COTB]
MG-COT Card [SCA-6COTC]
Analog MC
Analog 2MC
8LC Card [SCA-8LCA]
8LC Card [SCA-8LCA-EMEA]
VS32
VS-32
VS-32(Dual) Card [SCA-VS32VA]
VS-32(Dual) Box [MG-VS32VA]

TERMS-4
General Terms
• Automatic Number Identification (ANI) on this manual is a term equivalent to Calling Line Identification
(CLI) in Australia.

NWA-041691-001
ISSUE 1.0
JULY, 2008
UNIVERGE SV8500
PCPro Setup Manual
Page
– i –
CHAPTER 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1. Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Outline of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3. About Release Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4. Structure of Telephony Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.2 TP and SP for System Changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
5. Registration Destination of IP Devices/Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6. Lan Interface Accommodation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6.1 LAN1 Accommodation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6.2 LAN2 Accommodation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7. TRUNKING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CHAPTER 2 PCPro Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1. What Is PCPro? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Operating Environments and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.1 Operating environment of PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.2 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3. Conditions for Operating PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CHAPTER 3 Setting Up PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1. Installing PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2. Launching PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3. Connecting PCPro to the Telephony Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1 Serial / Direct Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1.1 Connection method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1.2 Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.2 Serial / Dial-up Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.1 Connection method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.2 Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.3 TCP/IP Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3.1 Connection method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3.2 Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.4 Modem Setting on IOC side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.5 Modem Setting on PCPro side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4. Communication Link with the Telephony Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4.1 Establishing a Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5. Clearing the Communication Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6. Security Setting for PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TABLE OF CONTENTS

– ii –
TABLE OF CONTENTS (CONTINUED)
Page
7. Exiting PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CHAPTER 4 PCPro Window Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
1. PCPro Window Component Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2. Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3. Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4. Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.1 System Data Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.2 Search Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5. Work Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6. Mode Selector Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7. Status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8. Scan Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
CHAPTER 5 Various Settings of PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
1. Connection Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2. User Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3. Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4. Login Grade Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
CHAPTER 6 Command Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
1. Commands without a Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2. Commands with a Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
CHAPTER 7 PCPro Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
2. Installing PCPro Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
3. PCPro Tools Window Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
CHAPTER 8 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
1. Uninstalling PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2. PCPro Error Message List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.1 Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.2 Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.3 Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.4 Connection Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.5 User Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
2.6 Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
2.7 Login Grade Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

– 1 –
CHAPTER 1 Introduction
CHAPTER 1 Introduction
1. Purpose
This manual covers procedures of installing “SV8500 PC Programming” (hereinafter “PCPro”) and “SV8500
PC Programming Tools” (hereinafter “PCPro Tools”), both as application tools for installing and servicing UNI-
VERGE SV8500 (hereinafter “SV8500”) and configuring its communication with the SV8500, along with help-
ful tips on configuring the system data.
For the details of each commands to be used on the PCPro, refer to Command Manual.
Note: The PCPro is available since Feature Package 7300 (R3)/FP30-100 R16. However, the MSVIP command
is not available.
2. Outline of This Manual
This manual consists of eight chapters. The following paragraphs summarize chapters 2 through 8.
•Chapter 2: PCPro Overview
Provides introductory information about PCPro and proceeds to describe its system configuration, operat-
ing environment, working conditions and more.
•Chapter 3: Setting Up PCPro
Explains how to connect the SV8500 and PCPro, how to install, launch and exit the application, establish
a communication link between the SV8500 and the PCPro.
•Chapter 4: PCPro Window Layout
Explains the PCPro window layout, submenus on the screen and the function of the work window, etc.
•Chapter 5: Various Settings of PCPro
Explains the various settings of PCPro.
•Chapter 6: Command Operation
Explains how to operate each commands to execute on the PCPro.
•Chapter 7: PCPro Tools
Explains how to use the PCPro Tools for uploading/downloading a data to/from the CF card of the system.
•Chapter 8: Appendix
Explains how to uninstall the PCPro, and the description of error messages.

– 2 –
CHAPTER 1 Introduction
3. About Release Information
The table below shows the relationship between IPX/SV7000 and SV8500 for the release information.
IPX/SV7000 SV8500
R25 S1
R26 S2
R27 S3

– 3 –
CHAPTER 1 Introduction
4. Structure of Telephony Server
4.1 General
This section explains the structure of Telephony Server, mainly about processors it has. Telephony Server has
TP and SP as processors on its CPU. Both TP and SP work together to provide various features. The following
are general description of TP and SP.
•TP: Telephony Processor, supports all the features provided in the system.
•SP: Signaling Processor, works as SIP server that handles call control signals using Session Initation
Protocol (SIP). SP consists of two parts - one for SIP terminals using a particular feature called
SIP TERMINAL ACCOMMODATION [S-146] (hereinafter called “SP (for SIP terminal)”), and
the other for other devices/stations using SP (hereinafter called “SP (MPH)”).
Note: Each of IP devices/stations communicates with either of them (TP/SP) as registration destination. For in-
formation about it, refer to “Registration Destination of IP Devices/Stations”.
4.2 TP and SP for System Changeover
In dual configuration, each processor may stay in active (ACT) or stand-by (STBY) state. ACT-side processors
handle each operation while STBY-side processors prepare for system changeover. Their states change when
system changeover is performed. The relationship between system changeover and the state of each processor
(TP/SP) is described below.
•TP: changes its state (ACT/STBY) according to the state of the system to which the TP belongs.
•SP: operates differently between two parts of SP.
• SP (for SIP terminal) Note 1: operates simultaneously with ACT-side TP.
• SP (MPH): is always in ACT (changeover is not executed).
Note 1: “SIP terminal” here refers to ones using SIP TERMINAL ACCOMMODATION [S-146] feature. For in-
formation about this feature, refer to the Data Programming Manual - Business.
TP
SP
Note 1
(for SIP Terminal) (MPH)
SP
System #1 (STBY)
TP
TP
System #1 (ACT)
System #0 (ACT) System #0 (STBY)
TP
ACT
System
Changeover
STBY
SP
Note 1
(for SIP Terminal)
SP
Note 1
(for SIP Terminal)
SP
Note 1
(for SIP Terminal)
(MPH)
SP
(MPH)
SP
(MPH)
SP

– 4 –
CHAPTER 1 Introduction
5. Registration Destination of IP Devices/Stations
Here lists IP addresses of Telephony Server to be assigned to each IP device/station as its registration destina-
tion. The IP address varies depending on several conditions, consisting of PH kind that handles the device/sta-
tion, protocol mode in which the device/terminal operates, and Telephony Server’s configuration. The table
below specifies the IP address necessary for each IP device/station, covering all the conditions.
Note: Device/terminal names in the table are general terms. If you want to know formal names of them, refer to
“TERMS IN THIS MANUAL” at the top of this manual.
Note: In this manual,Telephony Server may be referred as “DRS” or “SIP server” depending on the registration
destination. IP address of DRS/SIP server is, however, same as that of Telephony Server. Therefore, IP ad-
dress of DRS/SIP server is also as the table above.
Note 1: Telephony Server has two parts of processors on its CPU, TP and SP. For the information about it, refer to
“Structure of Telephony Server”.
Category
Device/Station
IP Address of
Registration Destination
CPU
Note 1 PH Protocol
mode
Single
Configuration
Dual
Configuration
TP
Internal PHE Proprietary
Protocol mode
Analog 2MC
MC&MG-COT (MC part)
IP-BS
VS32
LAN1 (ACT) LAN1 (ACT)
Internal PHI Proprietary
Protocol mode
MC&MG-COT (MG part)
MG-COT
MG(BRI)
MG(PRI) Note 2
MG(SIP)
LAN1 (ACT) LAN1 (ACT)
SP
MPH
SP-
PHD
Proprietary
Protocol mode IP terminal LAN1 (ACT) LAN1 (ACT)
SIP mode SIP terminal Note 3 LAN1 (ACT)
LAN1 (ACT)
/(System #0)
/(System #1)
SP-
PHI
Proprietary
Protocol mode
MC&MG-COT (MG part)
MG(BRI) LAN1 (ACT) LAN1 (ACT)
SIP mode
MG-COT
MG(BRI)
MG(PRI)
MG-T1(SIP)
8LC Card
VS32
LAN1 (ACT)
LAN1
(System #0)
/(System #1)
-SIPmode
WLAN Handset (MH Series)
Standard SIP Terminal LAN1 (ACT) LAN1 (ACT)