NEC LED-06AF1 User manual

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
User Manual
Control Software for LED Video Wall
LED Wall Manager
(English Version. 0.2)

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
Content
1. Preparation
2. Software Installation
3. Connection of Equipment
4. Setup LED Wall
5. Light Sensor
6. Control Video Processor
7. Trouble Shooting
Windows is a registered trademark of Microsoft Corporation.
HDMI is a trademark or registered trademark of HDMI Licensing LLC.

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
This software can set up LED Video Wall, control LED modules and get status of LED Video Wall.
1. Preparation
1.1 OS
Windows XP Home Edition / Professional SP3
Windows Vista...
Windows 7...
1.2 Specification of computer
CPU : OS requirement
RAM : OS requirement
USB : for USB/RS-485 adaptor
Serial Port : for Video Processor control. If no serial port, USB/RS-232 adaptor can be used.
1.3 Others
Microsoft .NET Frameworks 3.5 SP1

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
2. Software installation
2.1 Installation of the device driver of USB/RS-485 adaptor
Note: Connect USB/RS-485 adaptor to your computer after this installation process.
Set the CD-ROM in your computer.
Run SETUP.exe(Name is T.B.D.) (from ¥Driver¥SETUP.exe , the folder is T.B.D.)
Click .
Confirm the content and if you can agree it, select ”I accept the terms of the license agreement”.
Click .
Click .

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
Click .
After confirmation that “Launch the CP210x VCP Driver Installer.”is checked, click .
Click .
The following dialog box informs that the installation of the device driver is completed.
Click and set USB／RS-485 adaptor in your computer.

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
2.2 Installation of LED Wall Manager.
Before installation of LED Wall Manager, confirm Microsoft .NET Frameworks 3.5 SP1 or later version is
installed in your computer.
Set the CD-ROM in your computer.
Run SETUP.exe(Name is T.B.D.) (from ¥Software¥LED Wall Manager¥SETUP.exe , the folder is T.B.D.)
Click .

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
Click .
Check “Complete”and Click .
Click .

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
(On Installing)
Click , then installation is finished.
[Notes] The current problems of Application installation
(1) When installation is finished, the short-cut of Screen Service is registered in Stat-up. After re-starts
PC, Screen Service program runs and it cause that Configuration.exe cannot run. It is necessary to
close Screen Service which is resided in TASK TRAY.
(2) “Custom”installation does not work. It is same as “Complete”installation.

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
3. Connections of the equipment
3.1 Connections of Computer, USB/RS-485 adaptor and Video Distributor (LED-VD1)
(1) Set USB/RS-485 adaptor to your computer.
(2) Connect USB/RS-485 adaptor with Port1 (RJ-45) of Video Distributor with LAN cable (Straight type).
3.2 Connection between Computer and Video Processor (LED-VP1)
Connect Video Processor with your computer with RS-232 signal cable which is attached.
If your computer has no serial port, you can use USB/RS-232 adaptor. To use USB/RS-232 adaptor, please
read user manual of it.
Computer
USB/RS-485
LED-VD1
Computer
LED-VD1
Port-1
RS-232(Serial port)
DVI IN
LED-VP1

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
4. Set up LED wall
To run the software;
From Windows OS,
START Programs NECDisplaySolutions Configuration
Window Explanation
Icons Icon Function
Installation and Control of LED Wall.
Control Video Processor.
Registration of equipment
(Video Distributor, Light Sensor)
Communication setting for RS-485.

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
4.1 Communication Settings (RS-485)
(1) Confirmation of COM Port
Set USB/RS-485 adaptor to your computer.
[Windows XP]
START Control Panel System Hardware DeviceManager
Confirm Ports (COM & LPT).
[Windows Vista/Windows 7]
Control Panel HardwareandSound DeviceManager
Confirm Ports (COM & LPT).

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
(2) Communication Settings
To click have Communication window opened.
To click pull-down list of COM Port shows the COM port which can be used.
Select the COM Port which you confirmed by (1).
The other settings shall be used with default settings.
Click , then Communication window will be closed.

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
4.2 Registration of Equipments
Click , then Option window will be opened.
To click “New”shows the equipment list by pull-down menu.
Click “Distributor”, and then “Add VideoDistributor”window will be open.
Input the number from 1 to 40 at Device ID and input the number which is shown at Video Distributor.
After that, cluck .

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
(Caution)If Tag Name is wrong, following window will be displayed.
The digit is wrong. The wrong number is input.
If you need the registration of some equipments, repeat the process of “New ~ Add VideoDistributor”.
Device ID should be different number.
Click , then Option window will be closed.

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
4.3 LED Module Detection
Click , then three icons are displayed.
This process shows how many LED modules are connected for each output of Video Distributor.
Click , and “Module Table”window is opened.
Check ports which are used and click .
Tocheck “All”will search for all ports of Video Distributor output.
After detection of LED modules, the following window is displayed.
Click , then it is closed. On searching

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
Confirm the searching is correct and click , then “Module Table”will be closed.
Mapping of LED modules
Click , then “Screen Wizard”window is opened.
Click ofAdvanceSetting, open the advanced settings

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
Name Description
Screen Name TAB name which is registered.
Horizontal(Frame) To set the horizontal number of LED modules of LED Wall.
Vertical(Frame) To set the vertical number of LED modules of LED Wall.
Width(Pixel) To set the horizontal pixel of LED module.(*1)
Height(Pixel) To set the of vertical pixel of LED module.(*1)
Brightness Level Sets Dimming level(Brightness) when Mapping is completed.
No checked will set Dimming level is “0”. All LED will be turned off when mapping is
completed. Image will be black on LED Wall.
Checked will shows the spin bar. Select the value.
Gamma Sets the gamma correction after Mapping is completed.
No checked will set Gamma is “2.2”.
Checked will show the pull-down menu. Select the gamma correction (1.8, 2.0, 2.2, 2.4).
Signal Shift Signal timing offset. Do not change the default value.
*1: LED-06AF1: set “80”, LED-15BF1: set “32”.

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
Registration of LED modules
The mapping process is provided by Automatic and Manual
(1) Automatically
When LED modules are connected for horizontal by DVI-out of Video Distributor, automatic mapping is
available.
EXAMPLE: 4 x 3 LED Wall with LED-06AF1.
Set 4 at “Horizontal(Frame)”, Set 3 at “Vertical(Frame)”, Set 80 at “Width(Pixel)”and set 80 at “Height(Pixel)”.
Click , and go to the next step.
Module-1
[1]
Module-5
[1]
Module-9
[1]
Module-2
[2]
Module-6
[2]
Module-10
[2]
Module-3
[3]
Moduls-7
[3]
Module-11
[3]
Module-4
[4]
Module-8
[4]
Module-12
[4]
Port1
Port2
Port3

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
Click .
Click .
The color of Screen matrix will be changed to cyan, then click .
The mapping will start.
Yes
No

NEC Display Solutions, Ltd.
2010.09.28(Rev. 0.2)
If the following window is displayed, the mapping is completed. (Module mapping)
Click ,then “Screen Wizard”window will be closed.
The LED wall image is displayed as a follow.