Neopost Studiojet 110H User manual

NEOPOST
OWNER'S MANUAL·
Studiojet 11 OH
Infrared Sensor system
* Read all instructions carefully before use.
*To aviod fire or eletric shock, do not expose the products to rain or moisture.
1

NEOPOST Studiojet
11 OH
1. INTRODUCTION ............................................................................... 3
2. SAFETY PRECAUTIONS ..................................................................... 3
3. INSTALLATION .................................................................................. 4
4. SPECIFICATION ................................................................................ 4
5. PRODUCT IDENTIFICATION ............................................................... 5
6. CONTROL PANEL ............................................................................. 6
7. HOT TO PERFORM THE MACHINE ....................................................... 7
8. TEMPERATURE AND SPEED MEMORY SETTINGS ................................. 9
9. ROLLER TENSION SETTINGS ................................................... .. ...... .. 9
10. MAINTENANCE .............................................................................. 10
11. TROUBLE SHOOTING .................................................................... 10
2

NEOPOST Studiojet 110H
1. INTRODUCTION
Thank you for choosing NEOPOSTLaminator. It has been designed and manufactured to provide years of contnuous
service. For complete operating and maintenance information, please read this manual thoroughly.
Upon receipt your laminator, please inspect the box, the machine and all other contents for shipping damage.
Damage should be brought to the immediate attention of the delivering carrier
2. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury.
Please read the instructions carefully and keep this manual for future reference.
1. Only a licensed eletrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Do not allow articles of clothing (neckties, scarves, etc,) nearfront or near machine openings as they
could get caught by rollers and be pulled inside, causing serious personal injury.
4. Keep flammable and wet objects away from the machine.
5. To prevent possibility of electrical shock, do not immerse machine in water of permit liquid to spill in side.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the machine is turned off, cooled down and unplugged from the outlet prior to moving or repairs.
8. Keep away from children.
9. Close supervision is necessary when any appliance is used by or near children.
10. Do not open the case without authorized technicians.
11. Do not attempt to laminate items that exceed total recommended material thiskness for the unit.
12. Do not touch the rollers when it's hot status.
13. Do not use flammable sprays or materials when cleans the machine.
3

NEOPOST
Studiojet 11 OH
3. INSTALLATION
WARNING : The laminator should be installed by a trained service technician.
The laminator comes fully assembled, except for the guide table to avoid shipping damage.
Upon arrival, thoroughly inspect the unit. It is imperative that any shipping damaged is reported and claim is
filed with the delivering carrier immediately upon receipt.
The laminator should be located in an area with adequate work space for feeding graphics and lamination
materials. Avoid placing the laminator in a dusty area or near sources of extreme heat of cold.
Once the laminator is in right place, lock the casters into position. Always unlock the casters when moving
to a different location.
4. SPECIFICATION
MODEL
Studiojet 11 OH
Max. Laminating width 1200mm/1100mm (43.3")
Max. Laminating speed 4m I mins
Thickness of Mount 13 mm
Heating system Heating Roller
Q'ty of roller 4
Temperature control Yes
Speed control Yes
Display LCD
Preheating time 8 -
10 mins
Power supply AC220 -240V (50/60hz)
Power consumption 1,900 watts
Film Core Size 1",
58, 3" (All in One)
Dimension ( Stand is not included 1470/1440 x 460 x 272mm
Weight 120kgs
4

NEOPOST
Emergency
Switch
5. PRODUCT IDENTIFICATION
Film_Top
Studiojet 11 OH
Rewinder Shaft(1120H&C)
Control
Panel
Roller Tension
Handle
Film Tension
Foot Switch(1120/720)
~
Laminating Guide
End Cutter Side Cutter(1120/720) Core 1-3" Core Bolt
(1120/720)
Main Switch
(Top Roller Switch)
Bottom Roller Switch _____ __...
5

NEOPOST
Studiojet 11 OH
6. CONTROL PANEL
When the machine is initially turned on, the LCD window will display the last working preset memory settin~
READY SET TEMP SPEED
O O UU.,
0
= dJ
0 OO=°~dJ
11
[HOT) LJ QJ [coLD)
10
MEMO
0 ~
TEMP SPEED
QQ [YJ
1. TEMP .6.T : Adjust temperature.
9. READY: When the preset temperature is
2. SPEED .6.T : Variable speed from 1-9.
reached.
3. STBY : Temperature is set to 85 °C.
10. Rollers are running.
3. MEAS : Measures actual roller temperature.
11. Fans are running.
4. STOP : Stops rollers and Run rollers.
5. REV: Reverse action.
6. HOT: Initial setting to 110°C, speed 3.
7. COLD: Cold laminating.
8. MEMO: Memory function.
6

NEOPOST
7. HOW TO PERFORM THE MACHINE
1. Install the top and bottom film brackets.
2. Load the films. (The adhesive side facing the inside of roll =adhesive in)
Hot Laminating for Studiojet 11 OH
Film Bracket_Top
0 0 0 0
Fiim_Top
~Idle Bar Top
0
~ Safety Cover
Studiojet 11 OH
~J ~ /- Material
----?--<E----_,......0:::-....., rn-::::::::::~~- Guide Table
~ Film_Bottom
Idle Bar_Bottom
Film Bracket_Bottom
Cold Laminating for Studiojet 11 OH ( Hot & Cold )
r
---------------~-c-o-ld-Fl-lm------------,
Fiim Bracket_Top /
,,--: Rewinder
( ~~~;;;;;!=~~~
/ ~ldleBar_Top
0
lf Safety Cover
~ B ,-- Material
I I L..
( <, '"tR ___ __JL],~ Gulde Table
"-/
K / \Release Paper
IdleBar_Bottom __/ ~~ @ ) ~
~ Film Bracket_Bottom
0 0 0
7

NEOPOST
Studiojet 11 OH
3. Turn the power switch on. Power switch is located in the rear of the unit.
4. Remove the Safety Cover.
5. Remove the Guide Table.
'-4 f ,- Safety Cover
1
") /- Material
( ~)' Crc ___________ :j\_J~ Guide Table
6. Pull down the top film through the Idle Bar_ Top and attach it on the bottom roller.
/,...---Idle Bar_Top
/
//
,,.,---- Safety Cover
(- '\ 1 /- Materlal
( ~, ( c:._), CJL _________ ~L_1/,- Guide Table
7. Pull up the bottom film through the Idle Bar_Bottom and attach it on the top film of top roller.
Idle Bar_Bottom
~ f Cc?) f r'-&i
(
/..---~,,"-, /~ Film_Bottom
' , _ ) Fiim Bracket_Bottom
8. Set the Safety Cover and Guide Table.
9. Set the temperature and Speed
10. Align the material on the guide talbe and push the foot switch.
11. After the laminatined material pass the press roller, push the foot switch to stop
12. Make the roller tension handle set at the upper side.
13. Carefully pull up the laminating material in the back side of machine.
14. When it is ready, you can laminate.
8

NEOPOST
Studiojet 11 OH
8. TEMPERATURE AND SPEED MEMORY SETTINGS
You can set the temperature and speed for your convenient work through MEMO button.
You will receive the machine which set in factory. But you can change the MEMO value from 1-2.
.... Factory pre-set memory value
MEMO Temp(°C) Speed
.... How to change memory value
1 120
2 130
3
4
1. Press MEMO button for 2 seconds,
then flicker Temperature and Speed.
2 Up and down temperature and speed
3. Press 1 - 2 button
! Attention : If you don't use for 1 hours, the temperature will go to 85 "C of temperature.
Also when you press the StBy button, the temperature will go to 85 ·c of temperature.
Finally if you don't use 1 hours afterStBy mode, the power will be shut down automatically.
9. ROLLER TENSION SETTINGS
.... Generally it is used in Tension 4.
! Attention : If you don't want to laminate,
make the roller tension handle
set at the Zero tension
in the right image. Zero Tension
9
Tension 4

NEOPOST Studiojet
11 OH
10. MAINTENANCE
1. Lift up the rollers with Roller Press Handle, when it is not in use.
This will prevent the machine overheated.
2. Be sure to switch it off after use.
3. Operating with one roll of laminating film or when the upper and lower side of film is not in correct position
may leave melted resin on the rollers and it may damage the following lamination.
4. Adjust adequate tension on the film with tension handle. Ifthe tension is too tight, the film can be stretched.
5.Keep clean the rollers every time after use.
Remained resins and dusts can cause low laminating quality
11. TROUBLE SHOOTING
Symptom Cause Possible solution
a. Power plug is not plugged in. a. Plug the power cord into appropriate outlet
Machine will not turn
b. Power switch is "off" positon. b. Put the power switch to the "on" position.
on
c. Tripped circuit breaker. c. Reset the circuit breaker.
d. Blown main power fuse. d. Replace the fuse.
a. Emergency switch is engaged.
a. Disengage the emergency switch.
There is power, but
b. Safety cover is not closed.
b. Close the safety cover to active the safety
the rollers are not switch.
running after the hot
c. Guide table is not installed
c. Properly install the paper guide so that the
button is pressed: correctly. micro switch
is activated.
d. Blown motor fuse.
d. Replace the motor fuse.
a. The machine is in "COLD"
a. Switch to "HOT" mode.
The unit is not heating mode.
up
b. Set temperature is lower than
b. Raise the temperature according to the
the room temperature. recommended film temperature.
a. Upward curl
a. Loosen the top roll film tension.
Curled lamination
b. Downward curl
b. Loosend the bottom roll film tension.
a. The main roller temperatures
a. Raise the roller temperatures and lower the
Unclear lamination are too low and lamination lamination speed.
speed is too fast.
10