Nero 7433305 User manual

Nero Bluetooth Titanium Clock Radio
Product Number 7433305
Backed by the Nero 1 Year Warranty
OPERATING INSTRUCTIONS
SPEAKER SYSTEM WITH
2 USB CHARGING PORTS
FM RADIO TUNER
AND ALARM CLOCK
Images in this manual are for illustrative purposes only.
Due to constant improvements we advise that changes to the design,
material, specifications and product configuration may
occur at any time without notice.

E-4
E-3
LOCATION OF CONTROLS
1. SP EAKER
2. LED DISPLAY
3. BA CK-UP BATTERY
COMPARTMENT (BOTTOM OF UNIT)
4. USB-1 SOCKET
(DC CH ARGER: 5V/2000mA)
5. USB-2 SOCKET
(DC CH ARGER: 5V/1000mA)
6. SOURCE KE Y
7. FM MEMO RY KEY
8. CL OCK SET/ FM MODE KEY
9. VO LUM E KEY
10. KEY
11. KEY
12. PLAY/ PAUSE / PAIR KEY
13. VOLUME KEY
14. POWER ON / OFF KEY
15. ALARM SET KEY
16. SLEE P KEY
17. SNOOZE/ DIMMER KE Y
18. AUX INPUT SOCKET
19. DC JACK (DC 5V )
20. FM ANTENNA WIRE
AC OPERATION (EXTERNAL AC-DC POWER ADAPTOR)
POWER SUPPLY
- - -
-
+
FRONT VIEW:
BACK VIEW:
1
TOP VIEW:
3
17
19
18
20
6 7 8 9
10 11 12 13
14 15 16
2
45
- THIS SET IS EQUIPPED WITH A "DC-JACK" CAPABLE OF ACCEPTING
AC-ADAPTORS WITH A RATING OF DC = 5V, 3A, AND WITH A PLUG
WITH THE FOLLOWING POLARITIES AS SHOWN (CENTER POSITIVE) :
- PLEASE USE ONLY THE SUPPLIED AC-ADAPTOR TO OPERATE THE UNIT.
USE OF OTHER ADAPTORS MAY DAMAGE THE UNIT OR CAUSE IT TO MALFUNCTION.
- PLUG THE TAIL END OF THE AC-ADAPTOR INTO THE DC-JACK (SOCKET)
ON THE REAR OF THE UNIT.
- INSERT THE PLUG OF THE AC-ADAPTOR INTO A WALL OUTLET WITH AC-POWER.
- PRESS THE "ON/ OFF" KEY TO SWITCH ON THE UNIT.
- THIS UNIT IS DESIGNED TO OPERATE WITHOUT EVER BEING TOTALLY POWERED "OFF". IT
WILL EITHER BE "ON" OR IN "STANDBY MODE".
- IN STANDBY MODE, THE BACK-LIGHT OF THE DIGITAL DISPLAY WILL BE DIMMED
BUT THE DISPLAY WILL SHOW THE CURRENT TIME (CLOCK FUNCTION).
- ANYTIME DURING STANDBY MODE, YOU CAN SWITCH "ON" THE UNIT BY PRESSING
THE "ON/ OFF" KEY.
- SAVE ENERGY BY SWITCHING THE SYSTEM TO "STANDBY" MODE WHEN NOT IN USE. BACK
UP BATTERIES
- OPEN THE BATTERY DOOR AT THE BOTTOM OF UNIT.
- INSERT 2 PCS "AAA-CELL" (UM-4/LR03 TYPE) BATTERIES IN THE BATTERY
COMPARTMENT. THESE 2 BATTERIES ARE FOR BACKUP OF THE "CLOCK"
DURING BRIEF POWER OUTAGES.
D IMMER FUNCTION
THIS SET HAS A DIMMER FUNCTION TO ADJUST THE BRIGHTNESS LEVEL
OF THE DISPLAY BACKLIGHT. SIMPLY ADJUST IT AS DESIRED BY PRESSING
THE "SNOOZE/ DIMMER" KEY REPEATEDLY (HI-BRIGHTNESS / LOW-BRIGHTNESS / OFF)
THE DISPLAY BACKLIGHT WILL ALWAYS RETURN TO HI-BRIGHTNESS AS THE DEFAULT,
AFTER THE UNIT BEEN RESET.
DIGITAL CLOCK FUNCTION
-
HOW TO SET CORRECT TIME:
SWITCH UNI T TO "STAND-BY" MODE
PRESS & HOLD KEY FOR 3 SECOND S DISPLAY SHOWS
HOUR OR HOUR (FLAS HING)
12H 24H
PRESS OR KEY TO SEL ECT 12-HOUR OR
24-HOUR CLOCK DISPLAY SYSTEM & PRES S KEY TO CONFI RM YOUR
SELECTION.
PRESS REPEATEDLY TO SET
THE CORREC T HOUR IN THE DI SPLAY & PRES S TO CONFI RM.
OR KEY
KEY
CORREC T TI ME IS NOW SET & WIL L BE SHOWN IN THE DISPLAY.
PRESS REPEATEDLY TO SET
THE CORREC T MINUTE IN THE DISPL AY & PRES S TO CONFIRM
OR KEY
KEY
1.
2.
3.
4.
5.
6.
Set
Set
Set
Set
IN STANDBY MODE PRESS FM MEMORY KEY FOR 6 SECONDS, THE CURRENT TIME
WILL +1HOUR. PRESS AND HOLD FOR 6 SECOND AGAIN FOR -1 HOUR.
ONE TOUCH DAYLIGHT SAVINGS TIME SWITCH

4. PRESS AND KEY TO REACH THE MINUTES OF THE DESIRED
WAKE UP TIME, THEN PRESS THE KEY TO CONFIRM.
5. ADJUST THE VOLUME LEVEL AS DESIRED (FROM LEVEL 03-30) BY PRESSING
OR KEY. PRESS THE KEY TO CONFIRM.
E-6
SNOOZE FUNCTION
- WHENEVER THE ALARM COMES O N, IT C AN BE TEMPORARILY S USPENDED
FOR A SHORT P ERIO D O F 9 M IN UTES, BY P RESSIN G THE “ SNOOZE/ D IM MER” KEY
ONCE.
- THE ALARM W IL L THEN AUTOMATIC ALLY COME O N AGAIN AFTER THE 9 M IN UTES
“SNOOZE” PERIOD H AS ENDED.
- THE PROCEDURE C AN BE R EPEATED F OR APPROXIM ATELY 60 M INUTES F ROM
ORIG IN AL ALARM W AKE-UP TIM E.
2. THE SET WILL NOW AUTOMATICALLY SWITCH "ON" AT THE WAKE-UP TIME AS YOU
HAVE CHOSEN, AS LONG AS THE ALARM FUNCTION IS "ACTIVE".
3. TO TURN OFF THE UNIT AFTER IT HAS AUTOMATICALLY SWITCHED ON,
SIMPLY PRESS THE KEY ONCE. THIS WILL SWITCH OFF THE SET,
ALSO THE ALARM SETTINGS WILL CLEAR.
4. TO ACTIVATE THE ALARM AGAIN, REPEAT THE PROCEDURE OF "ALARM TIME
SETTING" AS DESCRIBED.
90
MINS
80
MINS
70
MINS
60
MINS
50
MINS OFF*
40
MINS
30
MINS
20
MINS
10
MINS
- THIS SET HAS A SPECIAL SLEEP TIMER FUNCTION WHICH CAN AUTOMATICALLY
SWITCH OFF THE UNIT. THIS IS USEFUL FOR SLEEPING TO MUSIC AT NIGHT.
- AT ANY TIME WHILE THE UNIT IS OPERATING, PRESS THE SLEEP KEY,
THE "SL" SYMBOL LIGHT ON, THEN PRESS THE SLEEP KEY REPEATEDLY
TO CHOOSE THE AUTOMATIC POWER OFF TIME.
(*OFF MEANS SLEEP TIMER IS DEACTIVATED)
AUTOMATIC POWER OFF SLEEP FUNCTION
BLUETOOTH® WIRELESS PLAYBACK
THE UNIT CAN WIRELESSLY STREAM AUDIO FROM ANY BLUETOOTH® DEVICE
WITHIN 30 FEET.
SIMPLY PAIR THE DEVICE AND ENJOY WIRELESS PLAYBACK AND CONTROL FROM
YOUR BLUETOOTH® DEVICE.
PREPARE THE UNIT:
- PRESS THE KEY TO TURN THE UNIT ON.
- PRESS THE SOURCE KEY UNTIL BT SYMBOL APPEARS.
- THE LED INDICATOR WILL FLASH SLOWLY TO INDICATE THE UNIT IS ON.
- PRESS AND HOLD "PAIR" KEY UNTIL THE LED INDICATOR FLASHING FAST AND
WAITING FOR PARING.
*NOTE ONLY ONE DEVICE CAN BE PAIRED AT ANY GIVEN TIME.
PREPARE YOUR PHONE OR OTHER BLUETOOTH DEVICE:
- TURN ON THE BLUETOOTH® FUNCTION, THIS IS USUALLY FOUND UNDER GENERAL
SETTINGS OR OPTIONS.
*PLEASE REFER TO YOUR DEVICE’S MANUAL FOR FURTHER BLUETOOTH® DETAILS.
MAKE THE CONNECTION:
- GO TO YOUR DEVICE’S BLUETOOTH® SETTINGS
- ADD OR SEARCH FOR DEVICES
- IF ASKED FOR A PASS CODE, ENTER “0000”
- THE LED INDICATOR WILL KEEP REMAIN LIT WHEN PAIRED.
*THIS IS A ONE-TIME EVENT PER DEVICE. TO PAIR YOUR UNIT TO ANY DEVICE,
REPEAT THE ABOVE PREPARATION AND CONNECTION STEPS.
®
E-5
SINGLE-DAY ALARM FUNCTION
EVERY TIME YOU SET THE WAKE-UP ALARM, IT WILL WORK ONLY ONCE (ONE TIME).
THIS MEANS THAT THE NEXT DAY, THE ALARM WILL BE RESET AND
WILL NOT AUTOMATICALLY WAKE UP AGAIN.
- THIS SET IS EQUIPPED WITH 2 ALARM MODES: BUZZER AND RADIO.
BEFORE SETTING THE ALARM, MAKE SURE TO SET THE CLOCK (SEE "DIGITAL
CLOCK FUNCTION" IN THE PREVIOUS SECTION) .
PREPARE FOR THE ALARM SETTINGS
1
2. PRESS AND HOLD KEY UNTIL THE DISPLAY WILL NOW SHOW:
. PRESS THE KEY TO PUT THE SET INTO "STANDBY" MODE
00 00
HOUR (FLASHING)
MINUTES
(FLASHING)
8 00
A. "ALARM" TIME SETTING
ONCE THE DESIRED SOURCE IS READY, PRESS THE KEY TO PUT THE SET
INTO STANDBY MODE AND THEN SHORT PRESS THE KEY REPEATEDLY
TO SELECT THE SOURCE AS DESIRED.
B. "ALARM" MODE SETTING
NOW SELECT THE SOURCE THAT YOU WISH THE UNIT TO PLAY AT THE "WAKE UP"
TIME AS BELOW:
FOR RADIO :
PRESS THE KEY TO SWITCH ON THE SET (DISPLAY BACKLIGHT WILL
BE "ON").
TUNE IN THE DESIRED STATION.
*REMARK: = BUZZER ALARM / = RADIO
FM
1. THE ALARM TIME IS NOW FULLY PROGRAMMED AND THE ALARM SYMBOL WILL
APPEAR TO INDICATE THAT THE ALARM FUNCTION IS "ACTIVE".
(DISPLAY SHOWS AS FOLLOWS)
CURRENT TIME
12:00 ALARM SYMBOL
AL
FM
FM SYMBOL
Set
Set
3. PRESS AND KEY TO REACH THE HOUR OF THE DESIRED WAKE UP
TIME THEN PRESS KEY TO CONFIRM.
THE DISPLAY WILL NOW SHOW:
Set
Set
Set

E-7
E-8
- PRESS THE KEY ONCE TO SWITCH ON THE UNIT.
- PRESS THE SOURCE KEY REPEATEDLY UNTIL THE DISPLAY SHOWS "FM".
- EXTEND AND ADJUST THE FM-WIRE ANTENNA TO OBTAIN THE BEST RECEPTION.
- USE THE KEY TO SELECT THE DESIRED MODE (STEREO/ MONO).
IN SOME CASES, WHERE RECEPTION IS POOR, IT MAY BE ADVISABLE TO
SELECT “MONO” MODE, TO IMPROVE CLARITY OF THE RADIO SIGNAL.
USING THE AUDIO LINE IN CONNECTION (AUX-INPUT)
- YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A MP3
PLAYER TO THIS UNIT, TO LISTEN TO THE SOUND OF THAT DEVICE THROUGH
THE HIGH QUALITY AMPLIFIER OF THIS MUSIC SYSTEM.
- TO CONNECT THE EXTERNAL DEVICE PLEASE USE A STANDARD STEREO HEADPHONE
(3.5MM TO 3.5MM PLUGS) CABLE TO CONNECT THE "HEADPHONE-OUT OR AUDIO
LINE-OUT" OF THE DEVICE TO THE AUX-INPUT SOCKET OF THIS UNIT.
- SELECT THE FUNCTION TO "AUX" BY PRESSING THE SOURCE KEY ONCE.
- SWITCH ON THE EXTERNAL DEVICE (eg. MP3-PLAYER).
- START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME CONTROL
OF THE UNIT TO THE DESIRED LEVEL.
- REMEMBER TO SWITCH OFF THE UNIT AND THE EXTERNAL DEVICE WHEN YOU ARE
FINISHED USING THE EXTERNAL DEVICE.
- AT ANYTIME DURING PLAYBACK, PRESS THE PLAY/PAUSE KEY TO PAUSE
OPERATION. PRESS AGAIN TO RESUME OPERATION AT THE SAME TRACK & POSITION.
- AT ANYTIME DURING PLAYBACK, “PRESS AND RELEASE” THE NEXT OR BACK KEY :
OR TO SKIP BACKWARDS OR FORWARDS BY ONE TRACK, AS DESIRED.
- PRESS THE PLAY/PAUSE KEY TO START PLAYBACK.
MUSIC PLAYBACK IN BLUETOOTH® MODE
ELECTRONIC VOLUME CONTROL
- THIS UNIT USES AN ELECTRONIC VOLUME CONTROL .
- TO INCREASE OR DECREASE THE LOUDNESS OF UNIT, PRESS
THE VOLUME UP (VOL +) OR VOLUME DOWN (VOL -) KEYS RESPECTIVELY.
- RELEASE THE KEY WHEN VOLUME LEVEL IS AT THE DESIRED LOU DNESS.
- SOMETIME S, ESPECIALLY DURING LISTENING TO THE RADIO, YOU MAY NOTICE
A "CLICK-CLICK-CLICK" (REPEATING) SOUND WH EN YOU ARE INCREASING OR
DECREASING THE VOLUME. THIS IS A NOR MA L CONDITION & THE SOUND WI LL
DISAPPEAR WH EN YOU RELEASE THE VOLUME KEY (WH EN YOU REACH THE
DESIRED VOLUME LEVEL).
(PUSH BUTTON TYPE)
OPERATION OF RADIO
DISABLING THE CONNECTION:
TO UNPAIR A BLUETOOTH® DEVICE THAT IS ALREADY PAIRED, PRESS AND HOLD
THE PAIR KEY FOR A FEW SECONDS.
VOLUME CONTROL:
INCREASE AND DECREASE VOLUME USING THE VOLUME UP AND VOLUME DOWN KEYS
ON THE UNIT OR USING THE VOLUME CONTROLS ON YOUR BLUETOOTH® ENABLED
DEVICE.
*NOTE :
(1) THERE IS NO PLAYBACK, ENSURE THAT NEITHER THE UNIT NOR YOUR
BLUETOOTH DEVICE ARE SET TO ZERO VOLUME AND THE CORRECT DEVICE
FOR PLAYBACK IS PAIRED.
(2) WHEN THE UNIT IS IN "PAIRING" MODE, IT SEARCHES FOR A CONNECTION,
BUT WILL AUTOMATICALLY SWITCH OFF THE PAIRING MODE IF NOTHING CONNECTS
TO THE DEVICE WITHIN 5-10 MINS.
®
AUTOMATIC FREQUENCY ADJUSTMENT (SEEK MODE)
- PRESS AND HOLD (FOR 2 SECONDS) THE OR KEYS TO “SEEK”
(AUTOMATICALLY ADJUST) THE RADIO
FREQUENCY “UP” OR “DOWN” TO THE NEXT AVAILABLE RADIO STATION.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY OF THE NEXT
STATION THAT IS FOUND.
- WHEN A DESIRED STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE
“MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
RADIO MEMORY (STATION PRESET MEMORY STORAGE)
- AT ANY TIME, THE CURRENTLY DISPLAYED STATION OR FREQUENCY CAN BE
STORED INTO ONE OF THE MEMORY POSITIONS.
- PRESS AND HOLD FM MEMORY KEY UNTIL "P01" FLASHES IN THE DISPLAY.
- PRESS OR KEYS TO SELECT DESIRED
MEMORY POSITION. (THERE ARE TOTAL 20 MEMORY POSITIONS).
- PRESS FM MEMORY KEY ONCE TO SAVE THE SELECTED STATION INTO THE
SELECTED MEMORY POSITION.
- TO RECALL ANY SAVED MEMORY, SIMPLY PRESS FM MEMORY KEY ONCE
THEN SELECT THE MEMORY POSITIONS BY PRESSING OR KEYS
THE SAVED RADIO-BAND WILL BE RECALLED.
- TO CLEAR THE MEMORY OF ANY POSITION, SIMPLY SAVE A NEW STATION TO THE
SAME MEMORY POSITION.
MANUAL FREQUENCY ADJUSTMENT (SCAN MODE)
- PRESS (AND IMMEDIATELY RELEASE) THE OR KEYS TO “SCAN”
(MANUALLY ADJUST) THE RADIO
FREQUENCY “UP” OR “DOWN” BY 1-STEP AT A TIME.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH
STEP’S POSITION.
- WHEN A DESIRED FREQUENCY OR STATION IS REACHED. IT CAN BE SAVED INTO
ONE OF THE “MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
2 x USB CHARGING FUNCTION
THIS UNIT IS DESIGNED TO ALLOW YOU TO CONVENIENTLY CHARGE
UP TO 2 USB DEVICES.
THE USB PORTS ALLOW FOR CHARGING NOT ONLY MOBILE PHONES BUT ALSO
HUNDREDS OF OTHER DEVICES, INCLUDING MOST BLUETOOTH® HEADSETS,
PORTABLE GAME CONSOLES AND MANY MORE. TO USE THE USB PORTS CHARGING
CAPABILITY:
CONNECT THE TAIL END OF THE USB CABLE (SUPPLIED WITH YOUR MOBILE PHONE
OR OTHER DEVICE) INTO ONE OF THE USB PORTS, AND CONNECT THE OTHER END
OF THE USB CABLE INTO YOUR MOBILE PHONE OR DEVICE.
THE UNIT WILL THEN AUTOMATICALLY BEGIN CHARGING THE RESPECTIVE DEVICE.
USB CHARGING PORT:
USB-1 SOCKET: 5V/ 2000mA
USB-2 SOCKET: 5V/ 1000mA
SPECIFICATIONS
POWER SUPPLY : ............ DC 5V, 3A THOUGH BUILT-IN DC JACK
EXTERNAL AC-DC POWER ADAPTOR 100V-240V ~ 50/60Hz
SPEAKER : ........................ SPEAKER 2" x 2
FREQUENCY : .................. FM 87.5 - 1 08 MHz
Set
Impor ted By R. Weatherdon & Co Pty Ltd
Sydney - Australia
www.weatherdon. com.a u
Made in China