Ness SCR PLUS Quick start guide
INSTALLATION NOTES
NESS SCR PLUS
Flexible Receiver
Product Part No. 106-179 (304MHz)
2
RELAY -
SCR+ is designed as a two-in-one
solution to replace both the SCR Single
Channel Receiver and the AUX Receiver.
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
RELAY OUTPUTINTRODUCTION
3
ON/ALARM
PANIC/TAMPER
received.
AUX
LOW BATT
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
NOTE: The Open Collector outputs require no
programming and are always active. The dipswitch
settings mentioned in this manual apply only to the
Relay Output.
OPEN COLLECTOR OUTPUTS INHIBIT INPUT
POWER INPUT
4
SWITCH OFF ON
1NORMAL OPERATING MODE PROGRAMMING MODE
OFF in NORMAL MODE ON in NORMAL MODE ON in PROGRAM MODE
2ON/OFF/ALARM/RESTORE
signals LATCH the relay
ON/ALARM signal
PULSES relay Program Code 1
3PANIC/TAMPER signal
TOGGLES relay
PANIC/TAMPER signal
PULSES relay Program Code 2
4AUX signal
TOGGLES relay
AUX signal
PULSES relay Program Code 3
5LOW BATTERY signal
LATCHES relay
LOW BATTERY signal
PULSES relay Program Code 4
LED OPERATION
TABLE – DIPSWITCHES
5
PROGRAMMING STEPS
1
1
ON
2 3 4 5
The LED will flash fast to indicate program
mode.
2
1
ON
2 3 4 5
If the selected code slot is blank the LED
will remain flashing fast. If the code slot
already has a device programmed the LED
will be ON. The existing radio device must be
erased before programming a new one.
See How To Erase a Code.
3
-
-
If the device being programmed already
exists in another code slot the LED will triple
flash on receiving the learn signals. If so the
device does not need to be programmed.
To program more devices repeat steps 1
and 2 for the remaining code slots.
4
The LED will flash slowly indicating normal
operating mode.
5
HOW TO ERASE A CODE
1
2
The LED will be ON indicating the slot is
programmed.
3
The LED will flash fast indicating the code
slot is blank.
PROGRAMMING / LEARNING TRANSMITTERS
6
below
RELAY OUTPUT OPERATION
1
ON
2 3 4 5
ON/OFF/ALRM
1
ON
2 3 4 5
ON/OFF/ALRM
7
RELAY OUTPUT OPERATION
1
ON
2 3 4 5
ON/OFF/ALRM
1
ON
2 3 4 5
ON/OFF/ALRM
8
RELAY OUTPUT OPERATION
1
ON
2 3 4 5
ON/OFF/ALRM
1
ON
2 3 4 5
ON/OFF/ALRM
not a
9
RELAY OUTPUT OPERATION
1
ON
2 3 4 5
ON/OFF/ALRM
1
ON
2 3 4 5
ON/OFF/ALRM
ACTION SWITCHES 2-5 INHIBIT INPUT RELAY
Latch
Low
Low
TABLE - RELAY OPERATION WITH INHIBIT INPUT
10
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
CONNECTION EXAMPLES
1
ON
2 3 4 5
1
ON
2 3 4 5
ON/OFF/ALRM
11
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
+12V
0V
INPUT
AUX
NO
NC
C
RELAY
LOW
BATT
PANIC
TAMP
ON/
ALARM
CONNECTION EXAMPLES
1
ON
2 3 4 5
ON/OFF/ALRM
1
ON
2 3 4 5
ON/OFF/ALRM
12
SPECIFICATIONS
4
Table of contents
Other Ness Receiver manuals
