NetComm NTC-220 User manual

User Guide
NTC-220
Doc No. UG01028

NTC-220 –User Guide
2 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Important Notice
This device, like any wireless device, operates using radio signals which cannot guarantee the transmission and
reception of data in all conditions. While the delay or loss of signal is rare, you should not rely solely on any
wireless device for emergency communications or otherwise use the device in situations where the interruption of
data connectivity could lead to death, personal injury, property damage, data loss, or other loss. NetComm
Wireless accepts no responsibility for any loss or damage resulting from errors or delays in transmission or
reception, or the failure of the NetComm Wireless NTC-220 Series router to transmit or receive such data.
Safety and Hazards
Warning –Do not connect or disconnect cables or devices to or from the USB port, SIM card tray, Ethernet port or the terminals of the
power connector in hazardous locations such as those in which flammable gases or vapours may be present, but normally are confined
within closed systems; are prevented from accumulating by adequate ventilation; or the location is adjacent to a location from which
ignitable concentrations might occasionally be communicated.
Copyright
Copyright© 2019 NetComm Wireless Limited. All rights reserved.
The information contained herein is proprietary to NetComm Wireless. No part of this document may be
translated, transcribed, reproduced, in any form, or by any means without prior written consent of NetComm
Wireless.
Trademarks and registered trademarks are the property of NetComm Wireless Limited or their respective owners.
Specifications are subject to change without notice. Images shown may vary slightly from the actual product.
Note –This document is subject to change without notice.
Save our environment
When this equipment has reached the end of its useful life, it must be taken to a recycling centre and processed
separately from domestic waste.
The cardboard box, the plastic contained in the packaging, and the parts that make up this device can be recycled
in accordance with regionally established regulations. Never dispose of this electronic equipment along with
domestic waste. You may be subject to penalties or sanctions under the law. Instead, ask for disposal instructions
from your municipal government.
Please be responsible and protect our environment.

NTC-220 –User Guide
3 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Document history
This document covers the following products:
NetComm Wireless NTC-220
VER.
D O C U M E N T D E S C R I P T I O N
D A T E
v1.0
First document release
8 November 2018
v1.1
New format and changes to signal strength LED mapping.
11 March 2019
v1.2
Updated signal strength LED mapping, added Appendix F: Serial
Port Wiring details.
25 March 2019
Table i. –Document revision history

NTC-220 –User Guide
4 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Contents
Overview ...........................................................................................................................................................................8
Introduction ....................................................................................................................................................................................................................8
Target audience .............................................................................................................................................................................................................8
Prerequisites ...................................................................................................................................................................................................................8
Notation ...................................................................................................................................................................................................................8
Product introduction ..........................................................................................................................................................9
Product overview............................................................................................................................................................................................................9
Product features.............................................................................................................................................................................................................9
Package contents...........................................................................................................................................................................................................9
Physical dimensions and indicators...................................................................................................................................10
Physical dimensions .....................................................................................................................................................................................................10
Interfaces.......................................................................................................................................................................................................................11
LED indicators...............................................................................................................................................................................................................12
Signal strength LEDs.............................................................................................................................................................................................13
LED update interval ..............................................................................................................................................................................................14
Ethernet port LED indicators......................................................................................................................................................................................14
Placement of the router ...................................................................................................................................................15
Mounting options.........................................................................................................................................................................................................15
Mounted flat against the wall ..............................................................................................................................................................................15
DIN rail mounting bracket....................................................................................................................................................................................16
Horizontal DIN rail mounting adapter ................................................................................................................................................................16
Wall mount with DIN rail mount adapter ...........................................................................................................................................................17
Wall mounted via DIN rail bracket ......................................................................................................................................................................17
DIN rail mount .......................................................................................................................................................................................................17
Ceiling mount via DIN rail bracket......................................................................................................................................................................18
Pole mount using DIN rail bracket ......................................................................................................................................................................18
Desk mount............................................................................................................................................................................................................18
Installation and configuration of the NTC-220 series router...............................................................................................19
Powering the router .....................................................................................................................................................................................................19
DC power via 6-pin connector.............................................................................................................................................................................19
DC power via field terminated power source....................................................................................................................................................19
Power consumption .....................................................................................................................................................................................................20
Average power consumption figures..................................................................................................................................................................20
Viewing power source information .....................................................................................................................................................................20
Installing the router......................................................................................................................................................................................................21
Advanced configuration...................................................................................................................................................22
Initialisation...................................................................................................................................................................................................................22
Configure as a new device...................................................................................................................................................................................23
Restore configuration from a previous backup file ...........................................................................................................................................24
Logging in.....................................................................................................................................................................................................................25
Status ..............................................................................................................................................................................26
Networking......................................................................................................................................................................30
Wireless WAN...............................................................................................................................................................................................................30
Data connection....................................................................................................................................................................................................30
Connect on demand.............................................................................................................................................................................................34

NTC-220 –User Guide
5 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Operator settings..................................................................................................................................................................................................38
SIM security settings .............................................................................................................................................................................................40
LAN................................................................................................................................................................................................................................44
LAN.........................................................................................................................................................................................................................44
DHCP......................................................................................................................................................................................................................45
Ethernet WAN/LAN.....................................................................................................................................................................................................48
Ethernet interface assignment.............................................................................................................................................................................48
Ethernet WAN .......................................................................................................................................................................................................49
PPPoE ............................................................................................................................................................................................................................50
WAN failover.................................................................................................................................................................................................................51
Hardware link.........................................................................................................................................................................................................51
Ping monitor ..........................................................................................................................................................................................................52
Routing..........................................................................................................................................................................................................................58
Static.......................................................................................................................................................................................................................58
RIP ...........................................................................................................................................................................................................................60
Redundancy (VRRP) configuration.......................................................................................................................................................................61
Port forwarding......................................................................................................................................................................................................63
DMZ ........................................................................................................................................................................................................................64
Router firewall........................................................................................................................................................................................................65
MAC / IP / Port filtering........................................................................................................................................................................................65
Creating a MAC / IP / Port filtering rule .............................................................................................................................................................66
VPN................................................................................................................................................................................................................................68
IPSec .......................................................................................................................................................................................................................68
OpenVPN...............................................................................................................................................................................................................72
PPTP client .............................................................................................................................................................................................................79
GRE tunnelling.......................................................................................................................................................................................................81
Services ...........................................................................................................................................................................83
Dynamic DNS ...............................................................................................................................................................................................................83
Network time (NTP) .....................................................................................................................................................................................................84
Data stream manager..................................................................................................................................................................................................85
Endpoints...............................................................................................................................................................................................................85
Streams...................................................................................................................................................................................................................97
PADD.............................................................................................................................................................................................................................99
Remote management................................................................................................................................................................................................100
SNMP....................................................................................................................................................................................................................100
TR-069...................................................................................................................................................................................................................103
OMA-Lightweight M2M .....................................................................................................................................................................................104
Timeouts...............................................................................................................................................................................................................106
GPS ..............................................................................................................................................................................................................................106
NMEA support.....................................................................................................................................................................................................106
GPS configuration...............................................................................................................................................................................................106
Mobile Station Based Assisted GPS configuration .........................................................................................................................................107
Odometer ............................................................................................................................................................................................................108
Geofence..............................................................................................................................................................................................................110
IO configuration .........................................................................................................................................................................................................113
Event notification .......................................................................................................................................................................................................115
Notification configuration ..................................................................................................................................................................................115
Event types...........................................................................................................................................................................................................117
Destinations.........................................................................................................................................................................................................118
Email settings .............................................................................................................................................................................................................120
SMS messaging..........................................................................................................................................................................................................121
Setup.....................................................................................................................................................................................................................122
SMS forwarding configuration...........................................................................................................................................................................123
Redirect to mobile ..............................................................................................................................................................................................123
Redirect to TCP / UDP server address..............................................................................................................................................................123
New message ......................................................................................................................................................................................................123
Inbox / Sent Items ...............................................................................................................................................................................................124
Diagnostics...........................................................................................................................................................................................................126
SMS diagnostics and command execution configuration..............................................................................................................................126
White list for diagnostic or execution SMS......................................................................................................................................................128

NTC-220 –User Guide
6 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Sending an SMS Diagnostic Command ...........................................................................................................................................................129
Types of SMS diagnostic commands................................................................................................................................................................129
SMS acknowledgment replies ...........................................................................................................................................................................130
SMS command format........................................................................................................................................................................................130
List of get/set commands...................................................................................................................................................................................132
List of basic RDB variables .................................................................................................................................................................................135
Network scan and manual network selection by SMS ....................................................................................................................................136
SMS diagnostics examples ................................................................................................................................................................................138
System .......................................................................................................................................................................... 140
Log...............................................................................................................................................................................................................................140
System log............................................................................................................................................................................................................140
Diagnostic log .....................................................................................................................................................................................................141
IPSec log...............................................................................................................................................................................................................142
Event notification log..........................................................................................................................................................................................143
System log settings.............................................................................................................................................................................................144
System configuration.................................................................................................................................................................................................146
Settings backup and restore..............................................................................................................................................................................146
Upload..................................................................................................................................................................................................................147
Package manager................................................................................................................................................................................................149
Administration ............................................................................................................................................................................................................150
Administration settings.......................................................................................................................................................................................150
Server certificate..................................................................................................................................................................................................154
SSH key management ........................................................................................................................................................................................158
LED operation mode ..........................................................................................................................................................................................160
Watchdogs..................................................................................................................................................................................................................161
Power management...................................................................................................................................................................................................163
Sleep settings ......................................................................................................................................................................................................164
Wake settings ......................................................................................................................................................................................................165
USB-OTG ....................................................................................................................................................................................................................166
Storage........................................................................................................................................................................................................................167
Reboot.........................................................................................................................................................................................................................169
Logging out .........................................................................................................................................................................................................169
Help ..............................................................................................................................................................................170
Appendix A: Tables .......................................................................................................................................................171
Appendix B: Default settings.......................................................................................................................................... 172
Appendix C: Recovery mode .........................................................................................................................................173
Status...........................................................................................................................................................................................................................174
Application Installer...................................................................................................................................................................................................175
Appendix D: HTTPS - Uploading a self-signed certificate................................................................................................ 177
Appendix E: RJ45 connectors ........................................................................................................................................ 179
Appendix F: Serial port wiring ........................................................................................................................................ 180
Appendix G: Obtaining a list of RDB variables................................................................................................................181
Appendix H: Using USB devices..................................................................................................................................... 182
Windows...............................................................................................................................................................................................................182
Mac OS.................................................................................................................................................................................................................182
Linux / Smartphones...........................................................................................................................................................................................182
Appendix I: Inputs/Outputs............................................................................................................................................ 183
Overview .....................................................................................................................................................................................................................183
Hardware Interface..............................................................................................................................................................................................183

NTC-220 –User Guide
7 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Wiring Examples..................................................................................................................................................................................................184
Open Collector Output driving a relay.............................................................................................................................................................184
Logic level Output...............................................................................................................................................................................................184
LED Output..........................................................................................................................................................................................................185
Digital inputs........................................................................................................................................................................................................185
NAMUR Sensor....................................................................................................................................................................................................186
Analogue Sensor with Voltage output..............................................................................................................................................................186
Analogue Sensor with 4 to 20mA output .........................................................................................................................................................187
Analogue Sensor with Thermistor.....................................................................................................................................................................187
System Example –Solar powered Router with battery backup......................................................................................................................188
Open source disclaimer .................................................................................................................................................190
Safety and product care .................................................................................................................................................190
Warranty........................................................................................................................................................................193

NTC-220 –User Guide
8 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Overview
Introduction
This document provides you all the information you need to set up, configure and use the NetComm Wireless
NTC-220 series router.
Target audience
This document is intended for system integrators or experienced hardware installers who understand
telecommunications terminology and concepts.
Prerequisites
Before continuing with the installation of your NTC-220 router, please confirm that you have the following:
An electronic computing device with a working Ethernet network adapter and a web browser such as Mozilla
Firefox® or Google Chrome™.
Notation
The following symbols may be used in this document:
Note –This note contains useful information.
Important –This is important information that may require your attention.
Warning –This is a warning that may require immediate action in order to avoid damage or injury.

NTC-220 –User Guide
9 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Product introduction
Product overview
Ruggedized industrial cellular router supporting 4G LTE Cat 1 with failover to 3G/2G.
An Ethernet port, a configurable RS232/RS422/RS485 Serial port and three multi-purpose I/O ports for
flexible local connectivity.
Integrated GPS support with an active GPS Antenna via an external SMA connector.
Industrial features, including a rugged enclosure, a wide operating temperature range, a wide input voltage
range and multiple wall mounting options.
Intelligent, Tri-Colour LED display for clear, easy to read modem status information
Ignition sensing port for graceful shutdown and startup in vehicle applications.
Configurable power save mode with minimum current draw when not operational.
VPN support for establishing a secure connection over public cellular network using OpenVPN.
Embedded Linux based OS with a 1GHz processor and 512MB of flash memory storage allowing for the
installation of custom, edge processing applications. Software Development Kit (SDK) is available.
Web interface for easy centralized configuration and management from any PC and full feature management
via secure SMS.
Support for firmware upgrades over the air.
Extensive device fleet management capabilities with support for TR-069, SNMP, LWM2M.
Roaming algorithm with prioritisation for cost effective, flawless network connection across the globe.
Product features
The NetComm NTC-220 is a feature-packed Industrial IoT device designed to provide real-time wireless
connectivity even in harsh environments at an affordable price. The Software Development Kit (SDK) allows you to
develop your own software applications for large scale compatibility and an easy path to large deployments across
a broad range of industries. The NetComm NTC-220 meets the global demand for a reliable and cost-effective
Industrial IoT device that successfully caters to mass deployment across businesses.
Package contents
The NetComm NTC-220 series router package consists of:
1 x NetComm NTC-220 Series router
2 x Cellular antennas
1 x 1.5m Yellow Ethernet cable
1 x DIN rail mounting bracket
1 x Quick start guide
If any of these items are missing or damaged, please contact your sales representative or the support team.

NTC-220 –User Guide
10 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Physical dimensions and indicators
Physical dimensions
Below is a list of the physical dimensions of the NetComm Wireless NTC-220 Series router.
Figure 1 –NTC-220 Series router top view
N T C - 2 2 0 S E R I E S D IM E N S I ON S
Length
148 mm
Depth
107 mm
Height
34 mm
Weight
221 grams
Table 1 –NTC-220 series dimensions

NTC-220 –User Guide
11 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Interfaces
The following interfaces are available on the NTC-220 series router:
Figure 2 –Left end interfaces
Figure 3 –Right end interfaces
I T E M
D E S C R I P T I O N
Main antenna socket
SMA female connector for main antenna.
Aux antenna socket
SMA female connector for auxiliary antenna (receive diversity).
GPS antenna socket
SMA female connector for an active GPS antenna.
Six-way terminal block
connector
Connect power source, ignition and I/O wires here. Power, ignition
and I/O wires may be terminated on optional terminal block and
connected to DC input jack. Refer to the diagram and table under
the Installation section for correct wiring of the terminal block.
Operates in the 8-40V DC range.
Reset button
Press and hold for less than 5 seconds to reboot to normal mode.
The LEDs are green and extinguish in sequence to indicate that
the router will reboot normally if the button is released during this
period.
Press and hold for 5 to 15 seconds to reboot to recovery mode.
The LEDs are amber and extinguish in sequence to indicate that
the router will reboot to recovery mode if the button is released
during this period.
Press and hold for 15 to 20 seconds to reset the router to factory
default settings. The LEDs are red and extinguish in sequence to
indicate that the router will reset to factory default settings if the
button is released during this period.

NTC-220 –User Guide
12 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
I T E M
D E S C R I P T I O N
SIM card slot
Insert SIM card here.
RJ45 Ethernet port
Connect one or several devices via a network switch here.
Mini USB 2.0 OTG port
Provides connectivity for optional external storage or a USB
Ethernet dongle. Supplies up to 0.5A to connected device.
Serial port
Female DB9 port supporting 9-wire RS-232, RS-485 or RS-422
(software selectable).
Table 2 –Interfaces
LED indicators
The NTC-220 series router uses 8 LEDs to display the current system and connection status.
Figure 4 –NTC-220 series router LED indicators
L E D
N A M E
C O L O U R
S T A T E
D E S C R I P T I O N
Power
Off
Power off
Double flash
Powering up
On
Power on
On
Power on in recovery mode
Slow flashing
Hardware error
Network
On
Connected via WWAN
Blinking
Traffic via WWAN
Slow flashing
Connecting PDP
On
Registered network
Slow flashing
Registering network
Slow flashing
SIM PIN locked
Fast flashing
SIM PUK locked
On
Can’t connect
GPS
Off
GPS function disabled
On
GPS function is enabled but no
satellite is detected.
Slow flashing
Satellite detected, acquiring location.

NTC-220 –User Guide
13 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
L E D
N A M E
C O L O U R
S T A T E
D E S C R I P T I O N
On
Satellite detected, location acquired.
Signal
strength
On
3G
On
2G GPRS
On
GSM only (no GPRS)
Table 3 –LED indicators
Note –The term “blinking” means that the LED may pulse, with the intervals that the LED is on and off not being equal.
The term “flashing” means that the LED turns on and off at equal intervals.
Signal strength LEDs
The following table lists the signal strength range corresponding with the number of lit signal strength LEDs.
LTE signal mapping (Green)
N U M B E R O F L I T L E D S
S I G N A L S T R E N G T H
All LEDs unlit
No signal
1
−115 dBm to −119 dBm
2
−105 dBm to −114 dBm
3
−100 dBm to −104 dBm
4
−90 dBm to −99 dBm
5
> −90 dBm
Table 4 –Signal strength LED descriptions
WCDMA signal mapping (Amber)
N U M B E R O F L I T L E D S
S I G N A L S T R E N G T H
All LEDs unlit
< –109 dBm
1
–109 dBm to –102dBm
2
–101 dBm to –92 dBm
3
–91 dBm to –86 dBm
4
–85 dBm to –78 dBm
5
≥–77 dBm
Table 5 –Signal strength LED descriptions
GSM signal mapping (Red)
N U M B E R O F L I T L E D S
S I G N A L S T R E N G T H
All LEDs unlit
< −109 dBm
1
−102 dBm to −108 dBm
2
−93 dBm to −101 dBm
3
−87 dBm to −92 dBm

NTC-220 –User Guide
14 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
N U M B E R O F L I T L E D S
S I G N A L S T R E N G T H
4
−86dBm to −78 dBm
5
>−78 dBm
Table 6 –Signal strength LED descriptions
LED update interval
The signal strength LEDs update within a few seconds with a rolling average signal strength reading. When
selecting a location for the router or connected or positioning an external antenna, please allow up to 20 seconds
for the signal strength LEDs to update before repositioning.
Ethernet port LED indicators
The Ethernet port of the NTC-220 series router has two LED indicators on it.
Figure 5 –NTC-220 series Ethernet port LED indicators
The table below describes the statuses of each light and their meanings.
L E D
S T A T U S
D E S C R I P T I O N
Green
On
There is a valid network link.
Blinking
There is activity on the network link.
Off
No valid network link detected.
Amber
On
The Ethernet port is operating at a speed of 100Mbps.
Off
The Ethernet port is operating at a speed of 10Mbps or no Ethernet cable is connected.
Table 7 –Ethernet port LED indicators description

NTC-220 –User Guide
15 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Placement of the router
The external high-performance antennas supplied with the router are designed to provide optimum cellular and
WiFi signal strength in a wide range of environments. If you find the signal strength is weak, try adjusting the
orientation of the antennas. If you are unable to get an acceptable signal, try moving the router to a different place
or mounting it differently.
Note –When selecting a location for the router, allow at least 20 seconds for the signal strength LEDs to update before trying a different
location.
Mounting options
The NTC-220 series router can be quickly and easily mounted in a variety of locations.
Mounted flat against the wall
When mounted flat against the wall, the NTC-220 series router has a slimline form factor. Use appropriately sized
screws in the mounting holes provided on the base of the unit.
Figure 6 –Wall mount –Flat against the wall

NTC-220 –User Guide
16 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
DIN rail mounting bracket
V Bend allows you to snap the DIN bracket onto the middle of a DIN rail rather than sliding it onto the end.
Figure 7 –DIN rail mounting bracket
Horizontal DIN rail mounting adapter
Used in conjunction with the DIN rail mounting bracket, this adapter lets you mount the NTC-220 series in a
horizontal orientation. With the DIN rail mounting bracket attached to the router, slide the adapter on to the
bracket as shown in the image below. You can then mount the device horizontally on a DIN rail. Optionally, you
may place a screw (max. 4.5mm diameter) through the centre hole of the adapter so that it doesn’t move along the
DIN rail.
Figure 8 –Horizontal DIN rail mounting adapter

NTC-220 –User Guide
17 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Wall mount with DIN rail mount adapter
Figure 9 –Wall mount with DIN rail mount adapter
Wall mounted via DIN rail bracket
Figure 10 –Wall mounted via DIN rail bracket
DIN rail mount
Figure 11 –DIN rail mount

NTC-220 –User Guide
18 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Ceiling mount via DIN rail bracket
Pole mount using DIN rail bracket
Figure 12 –Pole mount using DIN rail bracket
Desk mount
Figure 13 –Desk mount

NTC-220 –User Guide
19 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
Installation and configuration of the NTC-220
series router
Powering the router
The NTC-220 series router can be powered in one of two ways:
1DC power input via 4-pin connector (8-40V DC)
2DC power input via field terminated power source (8-40V DC)
The green power LED on the router lights up when a power source is connected. Nominal power input is (12V
DC/1.5A).
DC power via 6-pin connector
The positive and ground terminals on the 6-pin connector can accept power from a separately sold DC power
supply. Both a standard temperature range DC power supply and an extended temperature range DC power
supply are available to purchase as accessories.
If you have purchased an optional DC power supply, first remove the terminal block from the connector. The
terminal block connector uses rising cage clamps to secure the wires and ships with the cages lowered and ready
for wire insertion. Inspect the cage clamps and use a flathead screwdriver to lower the cage clamps if they have
moved during transportation. Insert the wires into the terminal block as shown below, noting the polarity of the
wires, then use a flathead screwdriver to raise the cage clamp to secure the wires in the terminal block. Insert the
wired terminal block into the terminal block connector of the router and then connect the adapter to a wall socket.
Figure 14 –Terminal block wiring diagram
DC power via field terminated power source
If an existing 8-40V DC power supply is available, you can insert the wires into the supplied terminal block to power
your router. Use a flathead screwdriver to tighten the terminal block screws and secure the power wires, making
sure the polarity of the wires is correctly matched, as illustrated below. You should avoid using DC cables greater
than 2 metres in length.
Figure 15 –Locking Power Terminal Block pinout

NTC-220 –User Guide
20 of 193
UG01028 v1.2 March 2019
© NetComm Wireless 2019
T E R M I N A L
D E S C R I P T I O N
+
Positive wire for power.
–
Ground wire.
i
Dedicated terminal for ignition detection.
I/O 1, 2, 3
Used for general purpose input/output (refer to the IO
configuration section for more information).
Table 8 –Locking power block pin outs
Power consumption
To assist with power consumption planning, the following table summarises average power consumption during
the various states of the NTC-220 series router under normal usage conditions. It is important to note that this
table serves as an indication only as the power consumed by the device is affected by many variables including
signal strength, network type, and network activity.
Average power consumption figures
P O W E R I N P U T
S T A T E
P O W E R C O N S U M P T I O N
12V
Powered on, all functions disabled
1.38 W
12V
Powered on, connected to LTE and idle
1.92 W
12V
Powered on, connected to packet data with heavy traffic
4.86 W
12V
Peak power draw at maximum 4G module transmission power
5.88 W
Table 9 –Average power consumption figures
Viewing power source information
You can view the current power input mode in the Advanced status section of the device’s web user interface. This
is useful for remotely monitoring the device. You can also use the Software Development Kit to access this
information for advanced purposes (e.g. configuring SMS alerts to inform you of the power status of the router).
To view the router’s power source information, log in to the router and expand the Advanced status box on the
status page. See the Status section of this manual for more information on the status page.