Netopia 3346-ENT User manual

1
Quickstart Guide
DL YNC
Power
LAN 4
LAN 3
LAN 2
LAN 1
Copyright © 2003, Netopia, Inc. All rights reserved. Netopia, Cayman and the Netopia logo are
registered trademarks and Making Broadband Work is a trademark of Netopia, Inc. All other
trademarks are the property of their respective owners.
Making Broadband Work™
V. 24/07/03
Cayman®3346-ENT
Cayman®3356-ENT
ADSL
Router

Check your package contents:
1. Unpack t e Netopia Cayman
D L YNC
Power
LAN 4
LAN 3
LAN 2
LAN 1
CD-ROM and Quickstart Guide
RJ-11 Telephone Cable
(lavender)
RJ-45 Ethernet Cable
(yellow)
Netopia Router: Cayman 3346-ENT
or Cayman 3356-ENT
Power upply
and Power Cord
2
1. After unpa king your Cayman Router shipping arton, de ide where you want
to lo ate the Router.
You should install the Netopia Cayman near your computer or another location
that permits easy access and visibility. You can lay the Netopia Cayman flat, or
mount it on a wall. Make sure any Ethernet cables are kept away from power
cords, fluorescent lighting fixtures, and other sources of electrical interference.
Put the Netopia Cayman in a location where air can circulate freely around it.
2. Conne t the Power Supply to the power ja k on the ba k panel of the Netopia
Cayman. Conne t the Power Cord to the Power Supply and plug it into an
appropriate ele tri al outlet.
Turn on the power using the power switch. The Power light should come on
solid green.
2. Set up t e Netopia Cayman

3
E
N
G
L
I
H
3. Conne t the Router to the phone wall ja k that supports your ADSL servi e.
Insert one end of the lavender telephone cable in the D L port on the Cayman
Router back panel. Insert the other end of the telephone cable into the tele-
phone jack connected to your AD L service. The DSL SYNC indicator light should
blink for up to two minutes and then come on solid green.
4. Conne t the Netopia Cayman to reate your Ethernet lo al area network (LAN).
Connect the yellow Ethernet cable to your first computer and to a LAN port on
the back of the Cayman Router. The LAN light for the port where you connected
the cable should blink briefly and come on solid green.
Note about onne ting your network:
After you have connected your first computer, please finish configuring your
router and Internet access before connecting any other computer or device.
When your router is configured and your Internet access is up and running,
connect each additional computer or device to a switch port on the back of the
Cayman Router with an Ethernet cable (maximum length 100 meters). If you
need more than four ports, connect a hub or a switch to the Netopia Cayman
using a standard Ethernet cable.
When all of your connections are made, the status LEDs on the front of your
Netopia Cayman will light, according to the following diagram:
Cayman 3346-ENT & Cayman 3356-ENT Front Panel
2. Set up t e Netopia Cayman (continued)
Power Off / On
LAN
DSL
412
3
to the phone wall jack
(AD L filter or splitter)
to the
power
jack
3
4
2
DL YNC
Power
LAN 4
LAN 3
LAN 2
LAN 1
Power - Green when power is on.
DSL SYNC -
Flashes green when training
olid green when trained.
LAN 1, 2, 3, 4 -
olid green when connected to each
port on the LAN.
Flashes green when there is activity
on each port.
Ethernet hub
or swit h

The following instructions assume that you want to use the automatic configuration
and address sharing features of the Router to provide IP information to devices on
your local Ethernet network.
1. Configure your omputer to use an IP address on the same TCP/IP network as
the Cayman Router:
> Windows 95, 98 and ME
On your computer, go to:
Open the network window by
double-clicking the Network I on.
(Windows ME users: if the network icon
is hidden, click on the “View All Control
Panel Options” - a link at the left-side of
the control panel window)
In the list of network components,
highlight the entry that says
“TCP/IP (your Ethernet ard here)”
and click
In the window that pops up,
select and click
Click the tab, select and click
Click the tab, remove any installed Gateways and click
Click the button again. When prompted, restart your computer.
Proceed to the next section “3. Configure the Netopia Cayman”.
Configure your Computer for Dynamic Addressing
4
DNS Configuration Disable DNS
Gateway

5
E
N
G
L
I
H
> Windows 2000 and XP
• Right click on the My Network Pla es icon on your Windows desktop
and select Properties from the drop-down menu.
• Right click on your Lo al Area Conne tion and select Properties.
• elect Internet Proto ol [TCP/IP].
• Click the Properties button.
• Click the Obtain IP address automati ally radio button and the
Obtain DNS server address automati ally radio button.
Click the OK button.
• Restart your PC.
• Proceed to the next section “3. Configure the Netopia Cayman”.
> Ma intosh Ma OS
Your Macintosh must be using Mac O 7.6.1 or higher.
• elect Control Panels from the Apple menu.
• Open the TCP/IP Control Panel.
• Choose Conne t: Via Ethernet.
• Choose Configure: Using DHCP Server. ave and close the
“Control Panels” window. You do not have to restart the Macintosh.
• Proceed to the next section “3. Configure the Netopia Cayman”.
> Ma OS X users
• Launch System Preferen es from the Dock or from the Apple Menu.
• elect the Network Preference Pane.
• Choose Show: Built-in Ethernet.
• Click the TCP/IP tab.
• Choose Configure: Using DHCP.
• Quit ystem Preferences. You do not have to restart the Macintosh.
• Proceed to the next section “3. Configure the Netopia Cayman”.
2. To onne t additional omputers that will use the address sharing features of
the Netopia Cayman, repeat step 1.
Configure your Computer for Dynamic Addressing (continued)

6
3. Configure t e Netopia Cayman
1. Run a Telnet appli ation from the omputer on the same network as the Router.
•W
indows users: click on the Start menu, select Run, and in the resulting
entry box, type telnet 192.168.1.1
• Ma intosh OS X users: launch the Terminal application, either from the
Dock or from the Utilities folder, and type telnet 192.168.1.1
• Classi Ma intosh OS users: you need to install the NC A Telnet
application, included on the Netopia CD, or freely available from user groups
or other freeware sources. Then launch NCSA Telnet and type 192.168.1.1
In the Telnet screens, move from field to field with the arrow keys. elect/execute
items with the Return key, and toggle items (Yes/No, On/Off, ...) with the Tab key
followed by Return.
A/ The Telnet window displays the Main Menu.
B/ The ADSL Line Con iguration screen appears.
>If your I P uses PPPoE, toggle PPP over Ethernet to On with the Tab key followed
by Return. If necessary, change the VPI and VCI to match those used by your I P.
>If your I P uses PPPoA, toggle Data Link Encapsulation to PPP and configure the
PPPoA default profile.
Cayman Router
Easy Setup...
WAN Configuration...
System Configuration...
Utilities & Diagnostics...
Statistics & Logs...
Quick enus...
Quick View...
Return/Enter goes to Easy Setup -- minimal configuration.
You always start from this main screen.
ADSL Line Configuration
Trellis Coding Enabled: On
Fast Retrain Enabled: On
Wiring Type AutoSense
Data Link Encapsulation RFC 1483
RFC 1483 ode Bridged 1483
PPP over Ethernet (PPPoE) Off
Data Circuit VPI (0-255) 8
Data Circuit VCI (32-65535) 35
PREVIOUS SCREEN NEXT SCREEN
Return/Enter takes you back to previous screen.
elect Easy Setup
and press Return.
Make any changes
that your I P
requires.
If necessary, turn
on PPPoE or
PPPoA.
elect NEXT SCREEN
and press Return.

7
E
N
G
L
I
H
3. Configure t e Netopia Cayman (continued)
If your ISP uses PPPoA, follow the instructions (the example below is based on
AD L “Wires Only” in the UK - parameters may change according to your I P):
If necessary, toggle PPP Mode from VC Multiplexed to LLC SNAP and change the
VPI and VCI to match those used by your Internet ervice Provider.
Please note:
This example is based on AD L “Wires Only” in the UK. AD L “Wires Only” uses
PPPoA and different VPI/VCI than those by default. As a result, you need to set
Data Link Encapsulation to PPP, VPI to 0and VCI to 38. PPP Mode remains VC
Multiplexed by default. Parameters may change according to your I P!
Proceed to the next screen.
C/ The Connection Pro ile 1: Easy Setup Pro ile screen appears.
The example below is based on IP Easy et Up using NAT by default.
et the Remote IP Address to 127.0.0.2 - this will allow the Netopia Cayman to
automatically pick up the IP address of the remote gateway of your Internet ervice
Provider. If you know this address, you can also enter it here.
et PPP Authentication to the mode used by your I P. In the BT Wires Only example
this would be CHAP mode. In the Send Host Name and Send Secret fields, enter
the login and password supplied by your I P. Proceed to the next screen.
Connection Profile 1: Easy Setup Profile
Address Translation Enabled: Yes
IP Addressing... Unnumbered
Remote IP Address: 127.0.0.2
Remote IP ask: 255.255.255.255
PPP Authentication... CHAP
Send Host Name: login
Send Secret: password_
PREVIOUS SCREEN NEXT SCREEN
Return/Enter brings you to next screen.
Enter basic information about your WAN connection with this screen.
Make any
changes
required.
elect NEXT
SCREEN and
press Return.
ADSL Line Configuration
Trellis Coding Enabled: On
Fast Retrain Enabled: On
Wiring Type AutoSense
Data Link Encapsulation PPP
PPP ode VC ultiplexed
Data Circuit VPI (0-255) 0
Data Circuit VCI (32-65535) 38
PREVIOUS SCREEN NEXT SCREEN
Return/Enter takes you back to previous screen.
Make any
changes
that your
I P requires.
elect NEXT
SCREEN and
press Return.

8
D/ The IP Easy Setup screen appears. Configure your LAN parameters here.
The example below is based on IP Easy et Up using NAT and DHCP erver.
The Domain Name and the IP addresses of your Primary and Secondary Domain
Name Server are dynamically acquired by the router when connecting to the
Internet. However, we recommend that you enter manually these information as
supplied by your I P. The other parameters allow you to change, if necessary, the
default settings and the DHCP erver features of your Cayman Router.
E/ The Easy Setup Security Con iguration screen appears.
Enter a Name and Password to limit access to the Router’s configuration screens.
Be sure to remember what you have typed because you will be prompted for it each
time you configure your Router. elect RESTART DEVICE and press Return.
2. The Cayman Router will then restart and your settings will take effe t.
Congratulations! Your installation is complete. You can now surf to your favourite
Web sites. If you have any questions or encounter problems, refer to the detailed
documentation on the Netopia CD, or contact our technical support. Answers to
many frequently asked product-related questions are also available on-line at:
http://www. netopia.com/support
Easy Setup Security Configuration
It is strongly suggested that you password-protect configuration
access to your Netopia. By entering a Name and Password pair here,
access via serial, Telnet and Web server will be password protected.
Be sure to remember what you have typed here, because you will be
prompted for it each time you configure this Netopia.
Write Access Name:
Write Access Password:
PREVIOUS SCREEN TO AIN ENU RESTART DEVICE
Configure a Configuration Access Name and Password here.
3. Configure t e Netopia Cayman (continued)
IP Easy Setup
Ethernet IP Address: 192.168.1.1
Ethernet Subnet ask: 255.255.255.0
Domain Name: ______
Primary Domain Name Server: 0.0.0.0
Secondary Domain Name Server: 0.0.0.0
Default IP Gateway: 127.0.0.2
IP Address Serving: On
Number of Client IP Addresses: 100
1st Client Adress: 192.168.1.100
PREVIOUS SCREEN NEXT SCREEN
Enter an IP address in decimal and dot form (xxx. xxx. xxx. xxx).
Set up the basic IP & IPX attributes of your Netopia in this screen.
Make any
changes
required.
The default IP
gateway must
match the
Remote IP add-
ress value that
you set on the
Connection
Profile screen
elect NEXT
SCREEN and
press Return.

Netopia Europe
2, rue du Docteur Lombard
92130 Issy-Les-Moulineaux
FRANCE
tel: [phone]
fax: [phone]
[email protected]
Netopia UK
c/o M. Nathan-Amissah
58 Poulton Avenue
utton
urrey M1 3PY
UNITED KINGDOM
[email protected]
Netopia Deuts hland
Am Fuchsberg 4
D-21423 WIN EN
DEUT CHLAND
[email protected]
Netopia Nederland
Becanusstraat 13
uite B04
6216 BX Maastricht
NEDERLAND
[email protected]
Internet
www.netopia.com
www.netopia-europe.com
www.netopia.co.uk
www.netopia.fr
www.netopia.de
www.netopiaAG.ch
www.netopia.it
Hotline
> in English
[phone]
suppor[email protected].uk
> en français (0,15 Euros HT/min)
N° local France : 0825 06 2424
DOM TOM : [phone]
suppor[email protected]
> auf Deuts h (für Swiss om &
Bluewin Kunden)
[phone] (2,5 CHF/min)
suppor[email protected]
Netopia Part Number 6180061-00-01
EU-ENT_3346-3356_Q G-240703