NetzHome WT17 User manual

WT17
Wi-Fi WATER TEMPERATURE SENSOR
QUICK START GUIDE
Getting started
1. Please check that your smart phone app is updated.
2. Please also check that your Wi-Fi router is working properly and
operates on 802.11b/g/n 2.4GHz with WPA/WPA2 encryption.
We also support OPEN encryption. i.e. no password
2.4GHz is the standard connection for most routers.
Please do NOT choose 5GHz connection.
Product Features
1. Built-in Wi-Fi module that sends all alerts to your Smartphone
2. Connect to any Normally Open or Normally Closed
Trigger Input. When the Sensor is triggered by a
change of state, it will send an Alert to your Smart
Phone or Tablet
3. Life-time cloud service is included
4. Simple Wi-Fi connection set up with APP
5. Individual tag setting from your smartphone
6. APP records last 30 activations time and date stamped
7. Schedule up to 4 periods per day when unit is automatically
turned off.
3
Installing the APP
１. Before powering up the device, please install our free
NetzHome APP onto your phone.
2. Now complete your User Profile by inputting your email
NetzHome
In the Box
Screwdriver
Wi-Fi Water Temperature Sensor QR Code Card
12
Setting up your DEVICE
Go to the location in the WIFI Building where you eventually wish to
install the Sensor. Look at your smart phone and ensure you have a
good and steady WIFI connection. Exit the APP, open SETTINGS
on your smart phone and click. If you just have a main Router, it will
be showing its reference (or SSID). However, if you have one or
more extenders, they may also be showing underneath. VERY
IMPORTANT –The Sensor will only communicate Alarm signals to
the WIFI Router or Extender that you are about to pair to so it is
essential that you pair it to the closest/strongest WIFI signal/SSID
address and a 6-to-20-digit password.
WIFI UNIVERSAL SENSOR
Universal Sensor

1. Please have the 2 new AA batteries ready for pairing,
but do not install yet
2. Make sure your smart phone is connecting to the Wi-
Fi network to be used by the device.
t
.
5. Input your Wi-Fi password.
6. Scan the QR code on Hang Tag or device. You
may also input the “UDID” manually.
Since WPS mode will not last long, make
sure you finish steps 6-8 as quickly as
possible.
6. Press the WPS button on your router (Optional
but recommended)
WPS/
Reset
Some RESET functions are combined with the WPS
button on Routers so refer to your Router User Manual
.
Short press the device to take you to the Device Page
1. Please have the 2 new AAA batteries ready for pairing, but do
not install yet
2. Re-Open the APP, go to Devices section, press and
then Start
3. Ensure that the Router SSID is the same that you have just
seen in your smartphone’s WIFI Settings or you will not be able to
pair successfully
4. Input your Wi-Fi password.
5. Scan the QR code on Hang Tag or device by moving your
smartphone’s camera directly above the QR code. You may also
input the “UDID” manually.
How To Use
Go to Devices section > Sensor column
Long press the device to set up the ‘mode’ of each sensor (i.e.
the ringtone/notification that appears on your phone).
Trouble Shooting
CANNOT PAIR THE DEVICE SUCCESSFULLY
1. If there are too many Wi-Fi connections around your
sensor, turn them off to avoid any disturbance and pair
again.
2. Check that the router is working properly and that it
operates on 2.4GHz.
3. Check that the SSID and password are correct.
4. Ensure the sensor is in pairing mode. Remember to remove
and reinstall the batteries each time you enter pairing mode.
If the blue LED indicator turns on, the sensor is ready to
pair. The whole pairing process continues until the “Pair
Finish” message appears.
DOESN’T WORK PROPERLY or LOSS OF SIGNAL ICON
APPEARS
1. Check whether the Sensor is within coverage of your
Wi-Fi router/repeater.
2. Check that the router is working properly.
3. Replace your batteries with new one.
7. If you want the Sensor to be Normally Open (activate when the
wires are closed) keep the 2 wires apart whilst pairing. If you want
the Sensor to be Normally Closed (activate when the wires are
open) keep the 2 wires closed whilst pairing.
8. Insert 2 new AAA batteries, making sure the polarity is correct.
9. Press ‘Pair’ and wait for network connection.
10. The device will now start pairing to the router.
11.When pairing is successful, a “Pair Finish” message will be
shown. A new device will be shown on device page. Otherwise,
please disconnect the batteries and repeat from step 4.