New Classic Furniture OBSIDIAN B1655-115 User manual

ASSEMBLY INSTRUCTIONS
B1655-115 OBSIDIAN 5/6-6/0 EK/WK HEADBOARD,FOOTBOARD
& SLATS
B1655-235 OBSIDIAN 6/0 WK SIDE RAILS
PARTS LIST
NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
1 OF 2
NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
2 OF 2
5
G
B
STEP 4.1 :
leveler
STEP 4.2 :
STEP 4.3 :
leveler
F
E
F
5
G
HARDWARE LIST
NO COMPONENT DRAWING QTY
AHeadboard 1 pc
BFootboard 1 pc
CHeadboard Right Side Facing
(RSF) Leg 1 pc
DHeadboard Left Side Facing
(LSF) Leg 1 pc
ESlat 4 pcs
FSlat Support Leg 8 pcs
GSide Rail 2 pcs
HHeadboard Stretcher 1 pc
NO COMPONENT DRAWING QTY
1JCBC M6 x 1 3/16" Blk 6 pcs
2Spring Washer 1/4" Blk 6 pcs
3Flat Washer 1/4"IDx4/8"OD Blk 6 pcs
4Allen Key M4 x 2 9/16" Blk 1 pc
5Allen Key M5 x 2 9/16" Blk 1 pc
6Pan Head Chipboard Screw
M3.5 x 5/8"mm Blk 12 pcs
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the parts list and/or hardware list shown.
6G
E
E
G
6
x8
STEP 1 : Attach Head Board Leg ( C & D ) to Head Board ( A ) as shown using JCBC BOLT ( 1 ) with Spring Washer ( 2 ), Flat washer ( 3 )
and securing with Allen Key ( 4 ) . 4
1
2
3
x6
D
C
A
x4
BACK VIEW
SUPPORT LEG MARKING
(BACK VIEW)
(FRONT VIEW) H
BACK VIEW
STEP 2 : Assemble Headboard Stretcher (H) to Headboard Legs (C & D) by using a screwdriver with Csk Screw (6).
H
6
D
H
STEP 3 :Hook side rail (G) to Headboard legs (C & D) and push it down to fit. Repeat with the other end of rail to hook onto Footboard (B).
Tighten the 4 corners with Allen Key (5)
STEP 4 :Install the Slat support legs (F) to the Slats (E). Assemble the slats (E) to the side rails (G) by using a screwdriver with hardware (6).
(Note: THE SET UP MUST BE DONE AT THE DESIGNATED LOCATIONS FOR THE BED TO BE STABLE)

NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
2 OF 2
5
G
B
STEP 4.1 :
leveler
STEP 4.2 :
STEP 4.3 :
leveler
F
E
F
5
G6G
E
E
G
6
x8
STEP 3 :
Hook side rail (G) to Headboard legs (C & D) and push it down to fit. Repeat with the other end of rail to hook onto Footboard (B).
Tighten the 4 corners with Allen Key (5)
STEP 4 : Install the Slat support legs (F) to the Slats (E). Assemble the slats (E) to the side rails (G) by using a screwdriver with hardware (6).
(Note: THE SET UP MUST BE DONE AT THE DESIGNATED LOCATIONS FOR THE BED TO BE STABLE)