New Space Design BVR-01 User manual
BVR-01 GPS Video Recorder
User Manual
New Space Design Co., Ltd.
Thewarrantycardandinformationareprintedwithusermanual
Warranty
BVR
GPS Video Recorder
ADSBV001-0
Video Recorder + GPS
Camera
01
Index
Description & Feature
Specification
Product Overview
Getting Started
User Interface
Question/Troubleshooting
Package List
Safety Precautions
................................................... 02
.................................................................... 03
........................................................... 04
............................................................... 06
................................................................. 17
.......................................... 26
.................................................................... 27
........................................................ 28
02
Description & Feature
01
BVR has the function of video recording with GPS information for outdoors. People
always like to memorize the happening from the picture or video. However, it doesn’t
provide the information of location. And, people are sometimes hard to recall it. From
BVR’s application, user can easily recall the image and location because we combine
all information together.
► VGA(640x480) with 300,000 pixels
► MPEG-4 A/V encode @ VGA 30 FPS
► MicroSD for storing video files
► Customize User Interface
► Camera view angle: 63 degree
► 2 batteries of AAA size
► Car charger for vehicle used
► Support time zone setting
► Support language: English, Traditional Chinese, and Simple Chinese
► Function of changing recording length
03
Specification
02
Array Element
Sensor Size
Image Transfer Rate(Max)
Scan Mode
Electronic Exposure
Pixel Size
Image Area
640x480 (VGA)
1/4”
VGA, CIF, QCIF, QQCIF －30 fps．
QVGA, QQVGA －60 fps
Progressive
Up to 510:1 (for selected fps)
6 μm x 6 μm
3.984 mm×2.952 mm
CMOS Sensor
Power Source
Power Consumption
Operating Temperature
Operating Humidity
1. AAA x 2 Battery ( Ni-H ),
2. Car Adapter (3V/1A)
350mA 2.4V
Under 65˚C
5% ~ 85%
Power
Environment
Appearance
GPS
GPS Chipset
Frequency
Channels
Antenna
Datum
Cold Start
Warm Start
Hot Start
Reacquisition
Sensitivity
Dimension
Weight
Storage
SiRF Star III
L1, 1575.42MHz
12 CH for tracking
GPS Patch Antenna
WGS-84
50 sec , average
33 sec , average
1 sec , average
< 1 sec
-158dbm
98 x 34 28mm
47.5g
MicroSD
*Above data is based on open sky condition
04
Product Overview
03
- Top View - - Bottom View -
Low Battery Indicator Screw hole for holder
Battery Cover
DC Jack
Record Indicator
GPS Indicator
Microphone
05
Product Overview
- Front View - - Back View -
- Left View -
Camera Power / Function Button
MicroSD Card SocketBuzzer
06
Getting Started
04
1. Insert MicroSD card 2. Open the battery cover and insert
two AAA batteries.
1. Battery Mold for bike
Note: 1. Please use MicroSD card of class 6 or Higher
2. Please use application to formation your
MicroSD before insert into the device
07
3. Attach the holder on the bottom of device.
Getting Started
08
Getting Started
4. Firm the holder with device by hand screw.
09
Getting Started
5. Assembly the mounting frame with device.
10
Getting Started
6. Place the device on the bike.
11
2. DC Mold for vehicle
Getting Started
2. Combine the holder with mounting frame
and attach it on the windshield.
1. Insert MicroSD card
Note: 1. Please use MicroSD card of class 6 or Higher
2. Please use application to formation your
MicroSD before insert into the device
12
Getting Started
3. Start the vehicle engine.
4. Plug in the DC jack of car adapter and connect the power cable with the car cigarette lighter.
13
Getting Started
5. Assembly the holder with device and adjust the device to make sure
that the camrea can get the best view.
14
3. Start the record function
Getting Started
1. Press the power switch (1 second). Then, release the power switch. The buzzer will have
a short beep.
15
Getting Started
2. GPS indicator lights up. It means that the device is searching GPS signal. when GPS fixed,
GPS indicator will start blinking by the interval of 3 seconds.
3. When record indicator starts blinking by the interval of 3 seconds, it means the device is
recording.
16
Getting Started
5. Press the power switch (3 seconds) when the system is power on. Then, release the power
switch. Record indicator will light up and buzzer will have a short beep. After that, Record
indicator will turn off. The buzzer will have a long beep during the same time. It means that
system is turned off.
4. Trun off the power
1. Insert the CD-ROM to your computer.
2. The system will automatically pop out the setup window. Or, you can double
click “Setup.exe” in CD-ROM drive
17
User Interface
05
1. Install application
18
User Interface
3. Click “Next” for the following setup.
4. After installing the application, there is an icon shows on the desktop.
19
User Interface
5. Connect MicroSD, unplugged from BVR, with PC.
6. Double click the icon to run the application.
Table of contents
