NewAge Products 66116 User manual

ATTENTION:Is your cabinet damaged?
Need help or spare parts? For fastest service,
contact NewAge Products at 1-877-306-8930;
or [e-mail].
Do not return to the retailer.
STOP
IM-OK2.03A-01
SKU#66116
45° Corner Cabinet
Stainless Steel
INSTALLATION GUIDE
Signature Outdoor Kitchen
For the online installation manual and videos regarding this product, please check out our support hub:
https://newageproducts.com/support-hub/outdoor-kitchen-stone

Index
Unpacking 2
Product Inspection 3
Product Specications 3
Tools Needed 4
Hardware Included 4
Assembling the 45° Corner Cabinet 5
Spare parts - 45° Corner Cabinet 11
Care and Maintenance of your Stainless Steel Cabinets 12
MANUFACTURER WARRANTY 13
Unpacking
• Begin by placing the package on a covered at surface.
• Remove all cardboard and foam packaging material.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools. See“Tools Needed”in the list below.

3
Product Inspection
• Check to see all parts are received as per the
order placed.
• Contact NewAge Products at 1-877-306-8930;
for any missing parts.
• Inspect the products for any damages before
starting the installation.
• Go through the installation instructions carefully
before starting the installation.
Product Specications
45° Corner Cabinet
SKU# 66116
W 20.99in x D 21.53in x H 34.75in
W
D
H

4
Tools Needed
Hardware Included
1 x #2 Phillips Bit
1 x Tape Measure
1 x 24” Level
1 x socket
1 x Socket wrench1 x Adjustable wrench
1 x Openend wrench 1 x #2 Phillips head
screwdriver
S.No. Description 45° Corner Cabinet
1Hex Head Bolt M6X50mm 4
2Flat Head Screw (#10x1in) (For mounting Fiber Cement Boards on Cabinets) 12
3Flat Washer M6 4
4Pan Head Screw M4X10mm 6
5 Leveling Leg M8 4
6Flange Hex Head Screw M6X12mm 12
7Rubber Gasket (For Countertop Assembly) 1
8Drill bit M4 (For mounting Fiber Cement Boards on Cabinets) 1
9Middle Leg 1
10 Rear Left Leg 1
11 Rear Right Leg 1
Hex Head Bolt
M6X50mm x2
Middle Leg x1 Rear Left Leg x1 Rear Right Leg x1
Flat Head Screw
(#10x1in) x12
Leveling Leg
M8 x3
Flat Washer M6 x4
Flange Hex Head
Screw M6X12mm x12
Pan Head Screw
M4X10mm x6
Rubber Gasket
(Supplied) X1
Drill Bit M4
(Supplied) X1
NOTE: Please refer to Signature Outdoor Kitchen Master Install Guide for (2), (7) and (8).

5
REAR FRAME
1
2
Place the two welded frames upright. Ensure the orientation as shown (A).
While holding the frames, place the bottom shelf on the base beams of both the frames.
Push the rear welded frame outward to t perfectly with the bottom shelf.
Holes closer to the bottom of the frame
Assembling the 45° Corner Cabinet
BOTTOM
SHELF
REAR
FRAME
FRONT FRAME
Top View
A

6
3
4
Assembling the 45° Corner Cabinet
Slide the bottom right side beam into the open channels of the frames. To ensure the correct
tment, place your ngers on the beam as shown (A) and push it towards the channel until the
snap t (B) engages completely.
Similarly install the bottom left side beam.
B
A
BOTTOM RIGHT
SIDE BEAM
BOTTOM LEFT
SIDE BEAM
Firmly press the beam
and push it into the
channel of the frame
Inserting
the Beam
After the snap-t
being engaged

7
5Slide the top right side beam into the open channels of the frames. To ensure the correct
tment, place your ngers on the beam as shown (A) and push it towards the channel until the
snap t (B) engages completely.
6Similarly install the top left side beam.
Assembling the 45° Corner Cabinet
B
A
TOP RIGHT
SIDE BEAM
Firmly press the beam as
shown and push it into
the channel of the frame
Inserting
the Beam
After the snap-t
being engaged

8
7
A
Install 6x Pan head screw M4. Ensure four screws on top (A) and two screws at the bottom (B).
8Flip the cabinet frame 180° on a safe and clean surface.
B
Assembling the 45° Corner Cabinet
180°

9
9Tighten the 3x Levelling Leg into the 3x leg provided (A). Install the 3 legs to the bottom of the
beams on the frame using 12x Flange hex head screw M6 as shown (B).
Assembling the 45° Corner Cabinet
10 Install the bottom toe kick to the front post with 2x Pan head screw M4 as shown (A).
A
A
B
LEVELLING LEG
FRONT POST
TOE KICK
LEG ASSEMBLY

10
11
12
Install the front post to the main frame with 4x Pan head screws M4 as shown (A).
NOTE: To fasten the False Frame Cabinets, use the hardwares (2x Hex head bolt M6, 4x Flat
washer M6) provided. Level Cabinets and tighten all bolts.
Assembling the 45° Corner Cabinet
A
Tighten the Bolt and Washer
directly on the Rivet Nut
provided on Cabinet.

11
1
2
8
9
3
6
7
4
510
11
Spare parts - 45° Corner Cabinet
Callout Engineering Part Number Description Qty
1OK2-17.004.01A-01 Rear Left Leg 1
2OK2-17.005.01A-01 Rear Right Leg 1
3OK2-17.006.01A-01 Middle Leg 1
4 H00196A-01 Leveling Leg M8 1
5 H00532A-01 Flange Hex Head Screw - M6X12 1
6OK2-17.007A-01 45°Corner Cabinet - Toe Kick 1
7H00204A-01 Pan Head Screws M4X10m 1
8H00199A-01 Flat Washer M6 1
9H00198A-01 Hex Head bolt M6X50mm 1
10 H00633A-01 Flat Head Screw (#10x1in) - For Fiber Cement Boards 1
11 OK2-10.006A-01 Rubber Gasket - For Countertop 1

12
Perform Regular Maintenance
OXIDIZATION Removal
List of common conditions that cause corrosion or
discoloration of stainless steel and should be avoided:
ber cloth.
After washing rinse in clean water and wipe the surface dry with your cloth remembering to go
with the grain on brushed stainless steel.
Generally you should wash your stainless steel every three months. Coastal areas or next to a
chlorine pool more frequently every 2 weeks.
Do not use abrasive cleaners or a scouring pad of any type as they will cause excessive wear and
nish.
nishes in coastal environments may show tea staining if not washed regularly.
ber cloth.
For better protection use a thin coating of protectant on the surface. We do not recommend using
this coating for food prep areas.
If you have oxidation there are a few steps to take to bring your stainless steel cabinets back
to“as new”condition.
Apply clean water with a cleaning sponge and rub gently in the direction of the grain. If the
mark won’t shift, it may be necessary to use a stainless steel cleaner, in which case apply the
cleaner and rub gently. After cleaning it is important to rinse the stainless steel with clean
with a soft cloth. Remember to always rub with the grain, NEVER across
nish, and the stainless can lose its shine. If you must use a scourer, use
a plastic scrub pad with no metal content.
1. Chloride containing cleansers – this includes bleach and any cleaners containing bleach
2. Muriatic acid (hydrochloric acid) – commonly used to clean up after tile/concrete installation
3. Concentrated soap residue – chemical additives will cause discoloration and some dried soaps
actually look like rust
4. Water with high iron content – can leave a rusty residue, especially if allowed to drip continuously
5. Contact with iron materials – including steel wool, iron residue/dust from installation or cleaning of
other steel products
6. Trapped moisture between the product and cover – rubber mats, metal cans or cleaner cans-
Allow cabinets to completely dry before covering.
7. Salts – contain chlorides
8. Extreme Heat by Flame
9. Do not permit citrus or tomato juice to remain on stainless steel surfaces.
10. No abrasive cleaners, steel wool pads, or abrasive cloths as they will scratch the finish.
Care and Maintenance of your Stainless Steel Cabinets

13
Scan this QR code with the camera
on your mobile device to visit the
NewAge Products Support Hub
www.newageproducts.com/support-hub/
Register your NewAge Products purchase online for quicker
customer assistance and access to exclusive benefits
Visit www.newageproducts.com/register/
Warranty Claim
For warranty service please contact NewAge Products at
1-877-306-8930; or [email protected]
Please review all warranty details below, prior to
contacting NewAge Products for a claim.
Scan the QR code on the right to access our support page or
visit www.newageproducts.com/contact-us/
PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
Please have the following information available
when you call our customer service team:
• Name, address and telephone number
• Product Name / SKU Number
• A clear, detailed description of the problem
• Proof of purchase including order number
NEWAGE PRODUCTS INC. SIGNATURE OUTDOOR KITCHEN CABINETS
LIMITED WARRANTY
WHAT IS COVERED
When this product is installed, operated and maintained according to the instructions attached to or furnished with the product
, NewAge Products
Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the wa
rranty duration from the
purchase date of the product.
Subject to the limitations and disclaimers set forth below or in other product documentation, Ne
wAge warrants to the initial customer that (1)
product fi nishes will be free from defects for three years following purchas
e, (2) drawer slides will be free from defects for two years following
purchas
e, and (3) the overall structural integrity of the product (not including finishes or drawer slides) will be free from defects for ten years
following purchas
e.
1.
Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.
2.
Damage resulting from products caused by accident, misuse, abuse, fire, flood, corrosion, improper installation, acts of God, neglect,
modification, improper maintenance and normal wear and tear or mishandling.
3.
Products damaged by improperly loading beyond the specified maximum weight capacity outlined in the instructions provided with the
product.
4.
Repairs or replacement when your product is used in other than normal, residential use, such as a commercial environment, or handled in
anyway inconsistent with the installation instructions included with the product.
5.
Cosmetic damage that occurs after customer purchasing the product, including scratches, dings, dents, corrosion, or stains in the material that
6.
Surfaces damaged due to improper use of chemicals, and detergents.
7
. Replacement parts for NewAge products outside Canada and the United States.
8.
Loss due to theft.
9
. Damage resulting from use of the product contrary and not in accordance to the instruction manual.
1
0. Any labor costs during the warranty period.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED
WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE E
XCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR
THE SHO
RTEST PERIOD ALLOWED BY LAW. THIS WARRANTY IS LIMITED TO THE ORIGINAL BUYER. Some states and provinces do not allow limitations
on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty give
s you specific legal rights, and
you also may have other rights that vary from state to state or province to provinc
e.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
Y
OUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AT OUR DISCRETION AS
PR
OVIDED HEREIN. NEWAGE SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
e
xclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific
legal rights, and you also may have other rights that vary from state to state or province to provinc
e.
WHAT IS NOT COVERED
MANUFACTURER WARRANTY

IM-OK2.03A-01
Nº d’UGS 66116
Armoire de coin à 45°
Acier inoxydable
GUIDE D’INSTALLATION
Cuisine extérieure Signature
ATTENTION: Votre armoire est-elle endommagée?
Vous avez besoin d’assistance ou de pièces de rechange? Pour obtenir un service plus rapide,
contactez NewAge Products au 1877306-8930;
ou écrivez à [email protected].
Ne retournez pas ce produit au détaillant.
STOP
Pour le manuel d'installation en ligne et les vidéos concernant ce produit, veuillez consulter notre centre
d'assistance:
https://newageproducts.com/support-hub/outdoor-kitchen-stone

Index
Déballage 2
Inspection du produit 3
Spécications du produit 3
Outils requis 4
Visserie incluse 4
Assemblage de l’armoire de coin à 45° 5
Pièces de rechange - Armoire de coin à 45° 11
Soins et entretien 12
GARANTIE DU FABRICANT 13
Déballage
• Commencer par placer l’emballage sur une surface plane doté d’un revêtement;
• Retirer l'ensemble du carton et du matériel d'emballage en mousse.
• Mettre au rebut/recycler tous les matériaux d'emballage;
• Vérier l’ensemble du contenu de la boîte et réunir les outils nécessaires. Consultez la section
«Outils requis» dans la liste ci-dessous.

3
Spécications du produit
Armoire de coin à 45°
Nº d’UGS 66116
L 20,99po x P 21,53po x H 34,75po
L
P
H
Inspection du produit
• Assurez-vous d’avoir reçu toutes les pièces
conformément à la commande que vous avez
passée.
• S’il manque des pièces, contactez NewAge
Products au 1877306-8930.
• Avant de commencer l’installation, inspectez les
produits pour y déceler tout dommage.
• Lisez attentivement les instructions
d'installation avant de commencer l’installation.

4
Outils requis
Visserie incluse
1 x #2 Phillips Bit
1 x Tape Measure
1 x 24” Level
1 x socket
1 x Socket wrench1 x Adjustable wrench
1 x Openend wrench 1 x #2 Phillips head
screwdriver
Nº
de S. Description Armoire de coin à 45°
1Boulon à tête hexagonale - M6x50mm 4
2Vis à tête plate (#10x1po) (Pour le montage des panneaux de bres de ciment sur les armoires) 12
3Rondelle plate M6 4
4Vis à tête cylindrique large M4X10mm 6
5 Patte de mise à niveau M8 4
6Vis à tête hexagonale à bride M6X12mm 12
7Joint en caoutchouc (pour l'assemblage du comptoir) 1
8Mèche M4 (pour le montage des panneaux de bres de ciment sur les armoires) 1
9Patte du milieu 1
10 Patte arrière gauche 1
11 Patte arrière droite 1
Boulon à tête
hexagonale
m6x50mm X2
Patte du milieu x1 Patte arrière gauche x1 Patte arrière droite x1
Vis à tête plate
(#10x1po) X12
Patte de mise à niveau
M8 x3
Rondelle plate M6 x4
Tête hexagonale à bride
Vis M6X12mm x12
Vis à tête cylindrique
large M4X10mm x6
Joint en caoutchouc
(fourni) X1
Mèche M4
(fournie) X1
REMARQUE: Veuillez vous reporter au Guide d'installation de la cuisine extérieure Signature pour les points (2),
(7) et (8).

5
CADRE ARRIÈRE
1
2
Placez les deux cadres soudés à la verticale. Veillez à l'orientation comme indiqué (A).
Tout en tenant les cadres, placez la tablette inférieure sur les montants de base des deux
cadres.
Poussez le cadre soudé arrière vers l'extérieur pour qu'ils s'adaptent parfaitement à l'étagère
inférieure.
Trous plus proches du bas du cadre
Assemblage de l'armoire de coin à 45°
TABLETTE
INFÉRIEURE
CADRE
ARRIÈRE
CADRE FRONTAL
Vue du dessus
A

6
3
4
Assemblage de l'armoire de coin à 45°
Faites glisser le montant latéral inférieur droit dans les canaux ouverts des cadres. Pour
s'assurer que l'ajustement est adéquat, placez vos doigts sur le montant comme indiqué (A) et
poussez-le vers le canal jusqu'à ce que l’élément encliquetable (B) s’engage complètement.
De la même façon, installez le montant latéral inférieur gauche.
B
A
MONTANT
LATÉRAL
INFÉRIEUR
DROIT
MONTANT
LATÉRAL
INFÉRIEUR
GAUCHE
Appuyez fermement sur
le montant et poussez-le
dans le canal du cadre
Insertion du
montant
Après l'engagement de
l’élément encliquetable

7
5Faites glisser le montant latéral supérieur droit dans les canaux ouverts des cadres. Pour
s'assurer que l'ajustement est adéquat, placez vos doigts sur le montant comme indiqué (A) et
poussez-le vers le canal jusqu'à ce que l’élément encliquetable (B) s’engage complètement.
6De même, installez le montant latéral supérieur gauche.
Assemblage de l'armoire de coin à 45°
B
A
MONTANT LATÉRAL
SUPÉRIEUR DROIT
Appuyez fermement sur le
montant comme indiqué
et poussez-le dans le
canal du cadre
Insertion du montant Après l'engagement de
l’élément encliquetable