Newgy Robo-Pong 2055 User manual

www.newgy.com
Robo-Pong 2055 and Robo-Pong 1055
OWNER'S MANUAL
•2055 Quick Start ......... 2
•1055 Quick Start ............. 4
•Operation .......................6
•Robot Positions ......... 18
•Misc. Adjustments ..... 19
•Drill Diagrams ..............21
•Speed Calib. Target . . 27
•RP.2.PC ......................... 28
•Important Notices .... 34
•Take-Down, 2055 ......35
•Maintenance ................37
•Chip Replacement ... 38
•Exploded Views ........ 39
•Parts List ...................... 44
•Warranty & Repair ... 46

2
2055 QUICK START
Pull down support legs
Place the robot on the table with the
open front side facing you. Pull the curved
black metal support legs toward you.
Spread Support Legs Apart
Spread out the sup port legs to their
fully open position.
Join Net Support Tubes
Turn the robot around 180° so the Net
Support Tubes are now facing you.
Grasp the second
tube from your
right and pull up,
removing it from its
storage hole. Place
the bottom of this
tube into the top
of the first tube
on your right as
shown. Repeat on
the left side.
Gently Lower Ball Trays
Grasp one of the Ball Return Trays,
lift straight up to unlock it, grasp the
adjacent Net Support Tube, and slowly
lower them into position. Be careful
not to let the tray or support tube slam
down. Repeat on the other side.
Verify All Parts
Unpack all the parts and check that all
are present. If unable to identify a part,
look for a small silver label with the part
name. If a part is missing, please contact
Newgy. You may want to keep your box
and styrofoam pieces in case you need to
ship your robot.
1
5
2
3
4
Pong Pal
(U.S. Only)

3
Attach the Robot to the Table
Pick up the robot by the center base
and secure it to the table by angling
it downward and against the table.
The support legs should be as wide as
possible before they go underneath the
table and the front support triangle sits
on top of the table.
Attach the Side Nets
Attach the side nets to your table tennis
table net by slipping the red flexible
band over your table net’s support
base and looping it over the table net’s
clamp screw.
Adjust Head Angle
Tilt the head downward as far as
possible by loosening the Brass Knob
and then re-tighten
after moving head.
Verify that the
word “topspin” is at
the top of the ball
discharge hole.
Place Balls* in Bucket
Open the bag(s) of balls. Wash and dry
them, and then place in the Ball Tray.
Add any additional new table tennis balls
that have been washed and dried, or any
used balls with a worn surface. All balls
must be 40mm or 40+mm in diameter.
(*Included with U.S. robots only.) Do not
mix 40mm and 40+mm balls.
6
8
9
10
11
7
Connect Cable to Robot
Plug one end of the Connec tor Cable into
the 5-Pin Connector on the back of the
robot as shown. Take
the other end of the
cable to the player's
end of the table.
Attach Bracket to Control Box
Turn Control Box upside down on the
table. Take the Mounting Bracket and
align the hole in the mount ing arm with
the threaded insert of the Control Box.
Secure bracket with Mounting Screw.
Leave Control Box
laying face down.
12
13
Connect Cables to Control Box
Bring the free end of the Connector
Cable to the pla yer’s end of the table.
Plug the Connector Cable into the 5-pin
socket on the bot tom of the Control
Box. Then insert
the Transformer’s
pin into the power
jack of the Control
Box.
Adjust Bracket to Top
Thickness
Pick up the Control Box and looking
across the round rubber pad of the
Adjustment Screw, raise or lower the
height of the rubber pad so it aligns
with the nearest mark on the bracket's
label that corresponds with the
thickness of your table's top.
Attach Control Box To Table
Angle the opening be tween the two
rub ber pads of the Mount ing Brac k et
towards the bot tom of your table's
apron. Slip the bracket onto the table.
The rectangular rubber pad of the
bracket should sit flat on the table's
top surface. If it is not flat, loosen or
tighten the Adjustment Screw until the
pad lays flat. This
is not a clamping
mechanism—do
not overtighten!
14

Obsah je uzamčen
Dokončete, prosím, proces objednávky.
Následně budete mít přístup k celému dokumentu.
Proč je dokument uzamčen? Nahněvat Vás rozhodně nechceme. Jsou k tomu dva hlavní důvody:
1) Vytvořit a udržovat obsáhlou databázi návodů stojí nejen spoustu úsilí a času, ale i finanční prostředky.
Dělali byste to Vy zadarmo? Ne*. Zakoupením této služby obdržíte úplný návod a podpoříte provoz a
rozvoj našich stránek. Třeba se Vám to bude ještě někdy hodit.
*) Možná zpočátku ano. Ale vězte, že dotovat to dlouhodobě nelze. A rozhodně na tom nezbohatneme.
2) Pak jsou tady „roboti“, kteří se přiživují na naší práci a „vysávají“ výsledky našeho úsilí pro svůj
prospěch. Tímto krokem se jim to snažíme překazit.
A pokud nemáte zájem, respektujeme to. Urgujte svého prodejce. A když neuspějete, rádi Vás uvidíme!