Newland NLS-HR200 User manual

NLS-HR200
Hand-held 2D Barcode Scanner
手持式二维码扫描器
Quick Start
快速使用指南
V2.0.0

Version/版本 Description/更新描述 Date/日期
V1.0 Initial release,only 6 pages .
最初版本，仅6页。 20090708
V 2.0.0 Support as from HR200 firmware V 3.06.007 and higher.
支持V 3.06.007 和更高的固件版本。 20100315
Revisions/版本信息

Getting to Start
Unpacking.......................................... E-01
Main Unit........................................... E-01
Accessories........................................ E-01
Outline and Function ......................... E-03
Specification ...................................... E-04
Distance of Field................................ E-05
Connect HR200 to the Host............... E-06
Removal of Communication Cable ... E-07
ON, OFF, IDLE, RESTART .............. E-08
Reading
Hand-held Mode................................ E-09
Hands-Free Mode .............................. E-10
Programming Code
Query ................................................ E-11
Factory Default.................................. E-12
Reading Mode ................................... E-13
RS232 Programming ......................... E-14
USB Programming ............................ E-17
USB HID-KBW Programming.......... E-18
Beeper................................................ E-21
Line Feed and Carriage Return.......... E-22
1D Symbols ....................................... E-23
2D Symbols ....................................... E-28
Appendix
A. Testing Codes................................ E-30
B. Digit Code and Save ..................... E-31
C. Troubleshooting ............................ E-32
开始使用
打开包装 ........................................... C-01
主机 ................................................... C-01
配件 ................................................... C-01
产品外观 ........................................... C-03
性能参数 ........................................... C-04
识读景深 ........................................... C-05
如何连接HR200和信息接收主机.... C-06
如何拆卸通讯线 ............................... C-07
开机、关机、待机和重启 ............... C-08
识读条码
手动识读模式 ................................... C-09
自动识读模式 ................................... C-10
常用设置码
查询命令 ........................................... C-11
恢复出厂设置 ................................... C-12
识读模式设置 ................................... C-13
RS232 通讯设置 ............................... C-14
USB 通讯设置 .................................. C-17
USB HID-KBW 相关设置................ C-18
提示音设置 ....................................... C-21
回车换行设置 ................................... C-22
1D 条码设置 ..................................... C-23
2D 条码设置 ..................................... C-28
附表
A. 测试样码 ...................................... C-30
B. 数据码和保存 .............................. C-31
C. 常见故障及判处方法 .................. C-32
Content 目录

E-01
请更换节标题
Getting to Start
HR200»
PS/2 Cable»
Unpacking
Unpack and check the main unit and accessories.In case there is any problem, please
contact with your dealer.
Main Unit
Accessories

E-02
Getting to Start
Accessories
Stand»
USB Cable»
RS232 Cable + Power Adapter»

E-03
Getting to Start
Outline and Function
Power Indicator
Led
Beeper
Scan Windows
Tag（S/N，Cetifications，etc）
Trigger
Cable Slot

E-04
Getting to Start
Specification
Performance
Image Sensor CMOS
Resoluing 752 * 480
Interface RS232 / HID-KBW / UDP / USB COM Port Emulation / HID-POS
Symbologies
2D PDF417, QR Code(Model 1/2), DataMatrix (ECC200, ECC000, 050,
080,100,140), Aztec, Maxicode, etc.
1D
Code128, EAN-13, EAN-8, Code39, UPC-A, UPC-E, Codabar,
China post 25,Interleaved 2 of 5, ISBN, Code 93, GS1 Databar,
Code 11,etc
Precision ≥5mil
Light Source LED(630 nm ±10 nm)
Light Intensity 300 LUX (130 mm )
Depth of Scan Field 30 mm ~ 445 mm
Print Contrast Signal ≥30%
Roll 360°
Pitch 45°
Yaw 45°
Illumination 0 ~ 100,000 LUX
Mechanical/ Electrical
Power Consumption 1.65 W
Voltage DC 5 V
Current
Max 330 mA
Oper. 290 mA
Idle 200 mA
Weight 250g
Environment
Operate Temperature -5°C - +45°C
Storage Temperature -40°C - +60°C
Humidity 5% - 95% ( non-condensing )
Certificates
FCC Part15 Class B, CE EMC Class B

E-05
Getting to Start
Distance of Field
36°
63mm Code 39 (5 mil) 120mm
25mm Code 39 (10 mil) 210mm
57mm PDF417 (5 mil) 115mm
37mm PDF417 (10 mil) 215mm
35mm QR Code (10 mil) 145mm
25mm QR Code (15 mil) 210mm
35mm Data Matrix (10 mil) 155mm
30mm Data Matrix (15 mil) 220mm
0 50 100 150 200 250

E-06
Getting to Start
Connect HR200 to the Host
Connecting with USB Cable
Connecting with PS/2 Cable
Insert PS/2 cable (RJ 45 male DIN) into HR2001、
cable slot;
Insert PS/2 cable (PS/2 male DIN) into Host PS/22、
female slot;
If necessary, connect PS/2 cable and the power3、
adapter;
If necessary, keyboard can connect to female slot4、
on the PS/2 cable.
Insert USB Cable (RJ45 male head) into HR2001、
cable slot;
Insert USB Cable (USB male head) into Host’s2、
(female) USB connector.
Connecting with RS232 Cable
Insert RS232 cable (RJ45 male head) into HR2001、
cable slot;
Insert RS232 cable (RS232 male head) into2、
Host’s (female) RS232 connector;
Connect RS232 cable and the power adapter.3、

E-07
Getting to Start
Removal of Communication Cable
A Pin that fit the HR200 “dismount hole”is needed. A paper clip could be ideal. Stretch one
end of the paper clip to fit the “Dismount Hole”. Follow the steps:
For RS232 and PS/2 connections, unplug the power adaptor.1、
Insert the Pin into “Dismount Hole”and keep some pressure.2、
Pull out the cable gently.3、
Pull out the Pin after the cable is removed.4、
Unplug the connector from the Host.5、

E-08
Getting to Start
ON, OFF, IDLE, RESTART
Connect HR200 and Host. One click the "Trigger". HR200 powers on and in "Idle" (ready to
use) state (factory default).
Power On
Power Off
There are 4 ways to "Power OFF":
Remove Cable Off HR200;»
Remove Power Adapter Off RS232 Cable;»
Remove USB Cable Off the Host;»
Remove PS/2 cable off the Host or power adaptor off.»
IDLE
When scanner is NOT reading, it is in "IDLE mode".
No reading attempt within a timeout, the Imager switch to IDLE mode automatically.
RESTART
If HR200 halted and does not respond to operations, please "Restart" by "Power OFF", and
then "Power ON".

E-09
请更换节标题
Reading
Hand-held Mode
Ensure HR200, cables, and the Host are connected, then turn the unit Power ON1、
Press & hold Trigger. Illumination LED and Aiming LED cast an Illumination Pattern2、
(red light) and an Aiming Pattern (blue light);
Keep Illumination Pattern in the center of a bar code. Zoom in and zoom out to allocate3、
the Optimum Reading Stance.
On a successful reading, there’ll be a beep sound,4、illumination & aiming patterns
die out. The HR200 then transmits barcode message to the Host.
NOTE: Experiences tell a certain range of distances has higher successful reading rate. This
range is the Optimum Reading Stance.

E-10
Reading
Hands-Free Mode
Adjust Height
Select reading mode “sensor mode”or “continuous mode”when working in hands-1、
free mode.
Adjust the stand height for the optimum reading stance.2、

E-11
请更换节标题
Programming Code
Code Programming ON
Code Programming OFF
Query
“Send Product Info”, the engine sends product information to the
Host immediately.“Send Sys Info when Power ON”, the engine sends
product information through RS232(only) to the Host after Power ON.
The system information is provided as follows:
Title Remarks
Firmware Ver Device Firmware Version
Build Time Device Firmware Version Establishing Time
Device ID Device Type
App Ver Device Application Version
uIMG Ver Device uIMG Version
Date Device Manufacture Date
S/N Device serial number
ESN User-defined device serial number
Manufacture ID Device Name
Interface 1 types of communication interfaces:
TTL232(EM3000) or RS232(EM2027), baud rate, parity check, data bits, stop bit
1D Indicate that reading 1D is allowed.
2D Indicate that reading 2D is allowed.
Scan Mode
Manual Scan1.
Auto Scan2.
Continuous Scan3.
Send Product Info
Send Sys Info when Power ON Do not Send Product Info when Power ON
(Factory Default)

E-12
Programming Code
Code Programming ON
Code Programming OFF
Factory Default
Part of Factory Default
Subject Factory Default
Interface
HR200R
RS232 and USB Self-adaption ，The default value is as below：
RS232（Baud Rate: 9600bit/s,Parity Check:No Check,Data / Stop
Bit:8 bits/1 bit); USB(HID-KBW)
HR200P PS/2 and USB Self-adaption ，The default value is as below：
PS/2(Stand KBW) ，USB(HID-KBW)
Beep On
Scan Mode Hand-held Mode
1D 1D Symbols（Enable）
Code128, EAN-13, EAN-8, Code39, UPC-A, UPC-E, Codabar,
China post 25,Interleaved 2 of 5, ISBN/ISSN, Code 93, GS1
Databar, Code 11,etc
2D 1D Symbols（Enable）PDF417, QR Code(Model 1/2), DataMatrix (ECC200, ECC000,
050, 080,100,140), Aztec, Maxicode, LP Code, etc.
Load All Factory Default

E-13
Programming Code
Code Programming ON
Code Programming OFF
Reading Mode
Hand-held Mode: Pull and keep holding the trigger line»
to read. Complete one reading or release the trigger to terminate
reading status.
Auto Mode: The ambient luminance change in front of the»
engine automatically initiates reading. After completion of reading,
the engine goes to idle. Both luminance change and the Trigger can
initiate reading when idle.
Continuous Mode: Pull the Trigger line low to start reading.»
The engine will keep reading. To stop, pull trigger line low again.
Hand-held Mode
(Factory Default)
Auto Mode
Continuous Mode

E-14
Code Programming ON
Code Programming OFF
Programming Code
RS232 Programming
Baud Rate
Under RS232 connection, the engine and the Host should set
communication baud rate to the same to keep normal communication.
Baud rate is the bits transmitted per second (8 bits per bytes). The engine
and the Host must communicate at the same baud rate.
The scanner supports baud rate as the following:
9600
（Factory Default）
2400
14400
38400
115200
1200
4800
19200
57600

E-15
Programming Code
Code Programming ON
Code Programming OFF
RS232 Programming
Parity Check
NO Check
(Factory Default)
Even Check
Odd Check
1 Stop Bit
(Factory Default)
2 Stop Bits
Stop Bits

E-16
Programming Code
Code Programming ON
Code Programming OFF
RS232 Programming
Data Bits Transmitted
8 Data Bits
(Factory Default)
7 Data Bits
6 Data Bits
5 Data Bits

E-17
Programming Code
Code Programming ON
Code Programming OFF
USB Programming
Select USB HID-KBW
Select USB DataPipe
Select USB COM Port Emulation
Select USB HID-POS
Note：A driver has to be installed before using USB DataPipe and USB COM Port Emulation.