NEXCOBOT RCB600 User manual

NexCOBOT Co., Ltd.
NexCOBOT Co., Ltd.
Published September 2023 www.nexcobot.com
IoT Automation Solutions Business Group
Industrial Robot Controller
RCB 600
User Manual

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. ii RCB 100 User Manual
Contents
Contents
Preface
Copyright ............................................................................................. iv
Disclaimer.............................................................................................. iv
Acknowledgements ............................................................................... iv
Regulatory Compliance Statements........................................................ iv
Declaration of Conformity...................................................................... iv
RoHS Compliance ................................................................................... v
Warranty and RMA ................................................................................ vi
Safety Information ................................................................................viii
Installation Recommendations...............................................................viii
Safety Precautions.................................................................................. ix
Technical Support and Assistance............................................................ x
Conventions Used in this Manual............................................................ x
Global Service Contact Information........................................................ xi
Package Contents.................................................................................xiii
Ordering Information ............................................................................xiv
Optional Accessories..........................................................................xiv
Chapter 1: Product Introduction
Overview ................................................................................................1
Key Features ...........................................................................................1
Hardware Specifications..........................................................................2
Knowing Your RCB 600 ..........................................................................4
Top View .............................................................................................4
I/O Interfaces.......................................................................................5
Chapter 2: Jumpers and Connectors
Before You Begin ....................................................................................5
Precautions ............................................................................................5
Jumper Settings ......................................................................................6
Locations of the Jumpers and Connectors...............................................7
Jumpers..................................................................................................8
AT/ATX Power Type Selection...............................................................8
RTC Clear ...........................................................................................8
Connector Pin Definitions .......................................................................9
External I/O Interfaces..........................................................................9
Audio Phone Jack................................................................................9
COM Ports.......................................................................................9
HDMI and VGA Ports .....................................................................10
LAN and USB 3.2 Ports...................................................................11
LAN and USB 3.2 Ports...................................................................12
LAN and USB 3.2 Ports...................................................................13
Internal Connectors...........................................................................14
Power Wire....................................................................................14
COM Ports.....................................................................................14
DC-in Connector............................................................................15
Pin Wire.........................................................................................15
Debug Connector ..........................................................................16
Front Panel Header.........................................................................16
Pin Wire.........................................................................................17
CPU Fan.........................................................................................17

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. iii RCB 100 User Manual
Contents
SATA Connector.............................................................................18
SATA Power Connector..................................................................18
Mini PCIe Slot ................................................................................19
NGFF Key B Connector...................................................................20
NGFF Key B Connector...................................................................22
Nano SIM Connector......................................................................24
SMBUS Power Connector...............................................................24
USB2.0 Connector .........................................................................25
USB2.0 Connector .........................................................................25
RTC Battery Connector...................................................................26
Block Diagram .................................................................................27
Chapter 3: BIOS Setup
About BIOS Setup.................................................................................25
When to Configure the BIOS.................................................................25
Default Configuration...........................................................................26
Entering Setup......................................................................................26
Legends................................................................................................26
BIOS Setup Utility..................................................................................28
Main .................................................................................................28
Advanced..........................................................................................29
Chipset..............................................................................................37
Security .............................................................................................41
Boot..................................................................................................42
Save & Exit ........................................................................................43

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. iv RCB 600 User Manual
Preface
PrefaCe
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without the prior written consent from Nexcobot
Co., Ltd.
Disclaimer
The information in this document is subject to change without prior notice
and does not represent commitment from Nexcobot Co., Ltd. However, users
may update their knowledge of any product in use by constantly checking its
manual posted on our website: http://www.nexcobot.com. NexCOBOT shall
not be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use of any product, nor for any infringements upon the rights
of third parties, which may result from such use. Any implied warranties of
merchantability or fitness for any particular purpose is also disclaimed.
Acknowledgements
RCB 600 is a trademark of Nexcobot Co., Ltd. All other product names
mentioned herein are registered trademarks of their respective owners.
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices and
describes how to keep the system CE compliant.
Declaration of Conformity
FCC
This equipment has been tested and verified to comply with the limits for
a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
(domestic environment) is likely to cause harmful interference, in which
case the user will be required to correct the interference (take adequate
measures) at their own expense.
CE
The product(s) described in this manual complies with all applicable
European Union (CE) directives if it has a CE marking. For computer systems
to remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. vRCB 600 User Manual
Preface
RoHS Compliance
NexCOBOT RoHS Environmental Policy and
Status Update
NexCOBOT is a global citizen for building the digital
infrastructure. We are committed to providing green
products and services, which are compliant with
European Union RoHS (Restriction on Use of Hazardous Substance in
Electronic Equipment) directive 2011/65/EU, to be your trusted green
partner and to protect our environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)
< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent
Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or
1,000ppm.
In order to meet the RoHS compliant directives, NexCOBOT has established an
engineering and manufacturing task force in to implement the introduction
of green products. The task force will ensure that we follow the standard
NexCOBOT development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NexCOBOT are renowned.
The model selection criteria will be based on market demand. Vendors and
suppliers will ensure that all designed components will be RoHS compliant.
How to recognize NexCOBOT RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the
suffix “(LF)” will be added to the compliant product name.
All new product models launched after January 2013 will be RoHS compliant.
They will use the usual NexCOBOT naming convention.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. vi RCB 600 User Manual
Preface
Warranty and RMA
NexCOBOT Warranty Period
NexCOBOT manufactures products that are new or equivalent to new in
accordance with industry standard. NexCOBOT warrants that products will
be free from defect in material and workmanship for 2 years, beginning on
the date of invoice by NexCOBOT.
NexCOBOT Return Merchandise Authorization (RMA)
▪Customers shall enclose the “NexCOBOT RMA Service Form” with the
returned packages.
▪Customers must collect all the information about the problems
encountered and note anything abnormal or, print out any on-screen
messages, and describe the problems on the “NexCOBOT RMA Service
Form” for the RMA number apply process.
▪Customers can send back the faulty products with or without accessories
(manuals, cable, etc.) and any components from the card, such as CPU and
RAM. If the components were suspected as part of the problems, please
note clearly which components are included. Otherwise, NexCOBOT is
not responsible for the devices/parts.
▪Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
▪Any products returned by NexCOBOT to other locations besides the
customers’ site will bear an extra charge and will be billed to the customer.
Repair Service Charges for Out-of-Warranty Products
NexCOBOT will charge for out-of-warranty products in two categories, one
is basic diagnostic fee and another is component (product) fee.
System Level
▪Component fee: NexCOBOT will only charge for main components such
as SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistor, capacitor.
▪Items will be replaced with NexCOBOT products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
▪Replace with 3rd party products if needed.
▪If RMA goods can not be repaired, NexCOBOT will return it to the
customer without any charge.
Board Level
▪Component fee: NexCOBOT will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistors, capacitors.
▪If RMA goods can not be repaired, NexCOBOT will return it to the
customer without any charge.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. vii RCB 600 User Manual
Preface
Warnings
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are inconsistent
with these instructions or the instructions for accessory modules, contact
the supplier to find out how you can ensure that your computer meets
safety and regulatory requirements.
Cautions
Electrostatic discharge (ESD) can damage system components. Do the
described procedures only at an ESD workstation. If no such station is
available, you can provide some ESD protection by wearing an antistatic
wrist strap and attaching it to a metal part of the computer chassis.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. viii RCB 600 User Manual
Preface
Installation Recommendations
Ensure you have a stable, clean working environment. Dust and dirt can get
into components and cause a malfunction. Use containers to keep small
components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
▪A Philips screwdriver
▪A flat-tipped screwdriver
▪A grounding strap
▪An anti-static pad
Using your fingers can disconnect most of the connections. It is recommended
that you do not use needle-nose pliers to disconnect connections as these
can damage the soft metal or plastic parts of the connectors.
Safety Information
Before installing and using the device, note the following precautions:
▪Read all instructions carefully.
▪Do not place the unit on an unstable surface, cart, or stand.
▪Follow all warnings and cautions in this manual.
▪When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪Avoid using the system near water, in direct sunlight, or near a heating
device.
▪The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. ix RCB 600 User Manual
Preface
Safety Precautions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect the equipment from any AC outlet before cleaning or installing
a component inside the chassis. Use a damp cloth. Do not use liquid or
spray detergents for cleaning.
4. To prevent electrostatic build-up, leave the board in its anti-static bag
until you are ready to install it.
5. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
6. Keep the board away from humidity.
7. Put the board on a stable surface. Dropping it or letting it fall may cause
damage.
8. Wear anti-static wrist strap.
9. Do all preparation work on a static-free surface.
10. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
11. Hold the board only by its edges. Be careful not to touch any of the
components, contacts or connections.
12. All cautions and warnings on the board should be noted.
13. Use the correct mounting screws and do not over tighten the screws.
14. Keep the original packaging and the anti-static bag; in case the board
has to be returned for repair or replacement.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. xRCB 600 User Manual
Preface
Technical Support and Assistance
1. For the most updated information of NexCOBOT products, visit
NexCOBOT’s website at www.nexcobot.com.
2. For technical issues that require contacting our technical support team or
sales representative, please have the following information ready before
calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
Warning!
1. Handling the unit: carry the unit with both hands and handle it with care.
2. Maintenance: to keep the unit clean, use only approved cleaning products
or clean with a dry cloth.
Conventions Used in this Manual
Warning:
Information about certain situations, which if not observed,
can cause personal injury. This will prevent injury to yourself
when performing a task.
CAUTION!
CAUTION!CAUTION! Caution:
Information to avoid damaging components or losing data.
Note:
Provides additional information to complete a task easily.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. xi RCB 600 User Manual
Preface
Global Service Contact Information
Headquarters
NEXCOM International Co., Ltd.
9F, No. 920, Zhongzheng Rd.,
Zhonghe District, New Taipei City, 23586,
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
www.nexcom.com
Asia
Taiwan
NexAIoT Headquarters
Industry 4.0 and Cloud Services
13F, No.922, Zhongzheng Rd.,
Zhonghe District, New Taipei City,
23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexaiot.com
NexAIoT Co., Ltd.
Taichung Office
16F, No.250, Sec.2, Chongde Rd.,
Beitun District,
Taichung City, 406, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexaiot.com
NexCOBOT Taiwan Co., Ltd.
13F, No.916, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcobot.com
GreenBase Technology Corp.
13F, No.922, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com.tw
DivioTec Inc.
19F-1A, No.97, Sec.4, ChongXin Rd.,
Sanchong District,
New Taipei City, 24161, Taiwan, R.O.C.
Tel: [phone]
Email: [email protected]
www.diviotec.com
AIoT Cloud Corp.
13F, No.922, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.aiotcloud.dev
EMBUX TECHNOLOGY CO., LTD.
13F, No.916, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.embux.com
TMR TECHNOLOGIES CO., LTD.
13F, No.916, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.tmrtek.com

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. xii RCB 600 User Manual
Preface
NEXGOL Chongqing
1st Building No.999,
Star Boulevard, Yongchuan Dist,
Chongqing City, 402160, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Beijing NexGemo Technology Co.,Ltd.
Room 205, No.1, Fazhan Rd.,
Beijing International Information Industry Base,
Changping District,
Beijing, 102206, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexgemo.com
Japan
NEXCOM Japan
9F, Tamachi Hara Bldg.,
4-11-5, Shiba Minato-ku,
Tokyo, 108-0014, Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom-jp.com
China
NEXSEC Incorporated
201, Floor 2, Unit 2, Building 15, Yard 3,
Gaolizhang Road, Haidian District,
Beijing, 100094, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexsec.cn
NEXCOM Shanghai
Room 406-407, Building C, No 154, Lane 953,
Jianchuan Road, Minhang District,
Shanghai, 201108, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
NEXCOM Surveillance Technology Corp.
Floor 8, Building B3, Xiufeng Industrial Zone,
GanKeng Community, Buji Street,
LongGang District,
ShenZhen, 518112, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
America
USA
NEXCOM USA
46665 Fremont Blvd.,
Fremont CA 94538, USA
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcomusa.com

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. xiii RCB 600 User Manual
Preface
Package Contents
Before continuing, verify that the RCB 600 package that you received is complete. Your package should have all the items listed in the following table.
Item Name Qty
1 RCB600 Mainboard 1
2 SATA Cable 1
3 SATA POWER Cable 1
4 COMPORT Cable 1
Optional Accessories
Item Part Number Name Description
1 603ATA0162X00 SATA Cable SATA CABLE ST:MD-6110066 SATA 7P/F/LATCH 180D TO 7P/F/LATCH 180D BLUE L=250mm
2 603POW0510X00 SATA POWER Cable SATA POWER CABLE ST:MD-6110034 SATA 15P/F/LATCH TO 1x4P H.S PH:2.5mm L=250mm
3 60233SIO62X00 COMPORT Cable COMPORT CABLE CP:NEX-110819-01 UL2651#28x9C-DB9+TU1001-10 L:200mm
4 5050200117X00 CPU COOLER CPU COOLER FOR NEX614A VER:A COOLJAG:JACDD04A-2D 60x60x26.5mm ANODE
Heat spreader >>
The heatspreader acts as a thermal coupling device to the module and is thermally coupled to the CPU via a thermal gap filler. On some
modules, it may also be thermally coupled to other heat generating components with the use of additional thermal gap fillers. Although
the heatspreader is the thermal interface where most of the heat generated by the module is dissipated, it is not to be considered as a
heatsink. It has been designed as a thermal interface between the module and the application specific thermal solution.

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. xiv RCB 600 User Manual
Preface
Ordering Information
The following below provides ordering information for RCB 600.
RCB 600 (P/N: 10J200RCB08X0)
Mini-ITX, 11th Gen Intel®Core™ i processors , 2 x DDR4 SO-DIMM,
1 x VGA, 1x HDMI, 7 x USB 3.2 (Gen1), 4 x USB 2.0, 3 x GbE LAN,
1 x SATA, 2 x RS232, 2 x RS232/422/485, 16-bit GPIO, 2 x DI/DO, WDT,
SMBus, 2 x M.2 Key B ,1 x mini-PCIe, onboard TPM, 24V DC
Optional Accessories
• SATA Cable (P/N: 603ATA0162X00)
• SATA POWER Cable (P/N: 603POW0510X00)
• COMPORT Cable (P/N: 60233SIO62X00)
• CPU Cooler (P/N: 5050200117X00)

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. 1RCB 600 User Manual
Chapter 1: Product Introduction
ChaPter 1: ProduCt IntroduCtIon
Key Features
▪11th Gen Intel®Core™ i processors
▪1 x VGA and 1 x HDMI display ports
▪2 x SO-DIMM DDR4 with non-ECC 3200MHz up to 64GB
▪2 x Intel®GbE LAN ports and 1 x 2.5 GbE LAN
▪7 x USB 3.2 (Gen1), 4 x USB 2.0
▪2 x RS232 and 2 x RS232/422/485
▪1 x SATA 3.0 port
▪1 x Full size mini-PCIe slot
▪2 x M.2 Key B
▪Onboard TPM
▪24V DC input
Overview

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. 2RCB 600 User Manual
Chapter 1: Product Introduction
Hardware Specifications
CPU Support
▪11th Gen Intel®Core™ i processors
▪i7-1185G7E (4C, 1.8GHz, up to 4.4GHz, TDP-up 28W) standard
▪i5-1145G7E (4C, 1.5GHz, up to 4.1GHz, TDP-up 28W) optional
▪i3-1115G4E (2C, 2.2GHz, up to 3.9GHz, TDP-up 28W) optional
Main Memory
▪DDR4 3200 SO-DIMM sockets supported dual channel, max 64GB
Display
▪1 x VGA (resolution up to 1920 x 1080@60Hz)
▪1 x HDMI 1.4b (resolution up to 3840 x 2160@30Hz)
Tip: Multiple display: (VGA+HDMI)
System
▪7 x USB 3.2 (Gen1), 4 x USB 2.0
▪2 x RS232, 2 x RS232/485/422, 1 x CAN bus
▪Realtek HDA Codec
▪1 x Front panel header, 16 bit digital I/O (8-in/8-out), 2 x DI/DO
▪WDT, SMBus, onboard TPM
▪1 x Fan connector
Storage
▪1 x SATA 3.0, 1 x SATA power connector (+5V)
▪1 x M.2 2242/2280 Key B (support SATA/PCIe)
Expansion Slot
▪1 x Full size mPCIe x1 with nano SIM (support PCIe/USB 2.0 Interface)
▪1 x M.2 3052/3042 Key B (for LTE 5G), (USB 3.2 (Gen1)/PCIe) with nano
SIM
Rear I/O
▪6 x USB 3.2 (Gen1)
▪1 x VGA, 1 x HDMI 1.4b
▪2 x DB9 (by COM 1,2)
▪3 x GbE LAN
- LAN1: Intel®I219-LM
- LAN2: Intel®I210-AT
- LAN3: Intel®I226-IT
▪1 x 2 ports HD Audio Jack (Mic-in, Line-out)
Internal I/O
▪2 x USB 2.0
▪4 x serial ports:
- 2 x RS232 (by COM 3,4)
- 2 x RS232/485/422 (by COM1,2)
▪1 x CAN Bus
▪1 x Front panel header, 1 x 16 bit digital I/O (8-in/8-out)
▪2 x DI/DO, WDT, SMBus
▪HA Audio:
- 1 x Line-out, 1 x Mic-in
▪1 x 4-Pin DC-in (+24V)

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. 3RCB 600 User Manual
Chapter 1: Product Introduction
Power Requirement
▪1 x 4-pin (2 x 2) ATX power connector
- Input power DC 24V
▪Support both AT and ATX power supply mode
Dimension
▪6.7”x 6.7” (170mm x 170 mm)
Environment
▪Board level operation temperature: 0°C to 60°C
▪Storage temperature: -40°C to 85°C
▪Relative humidity:
- 0% to 90% (operating, non-condensing)
- 0% to 90% (non-operating, non-condensing)
Certifications
▪CE/FCC Class A&IEC 61326-3-1
Support OS
▪Windows 10 (64bit)
▪Ubuntu 21.04.0/Kernel 5.8

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. 4RCB 600 User Manual
Chapter 1: Product Introduction
Knowing Your RCB 600
Top View
CAN1 DIDO1 DC_VIN1
SMBUS1 W_BAT1
JRTC1
USB_FW1
USB1
USB2
COM2
COM3
SIM1
NGFF1
NGFF2
JSATA1
JSP1
MPCIE1
DIMM1
DIMM2
ESPI_DB1
GPIO1 JFAN1 FRONT1DEBUG1
AT_ATX1

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. 5RCB 600 User Manual
Chapter 1: Product Introduction
I/O Interfaces
USB 3.2
Gen1 Type-A
USB 3.2
Gen1 Type-A
USB 3.2
Gen1 Type-A
COM1B
COM1A VGA LAN1
Intel®i219
LAN2
Intel®i210
LAN3
Intel®i226
Line Out
HDMI 1.4b Mic In

Copyright © 2023 NexCOBOT Co., Ltd. All Rights Reserved. 5RCB 600 User Manual
Chapter 2: Jumpers and Connectors
ChaPter 2: JumPers and ConneCtors
This chapter describes how to set the jumpers and connectors on the
RCB 600 motherboard.
Before You Begin
▪Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
▪Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
– A Philips screwdriver
– A flat-tipped screwdriver
– A set of jewelers screwdrivers
– A grounding strap
– An anti-static pad
▪Using your fingers can disconnect most of the connections. It is
recommended that you do not use needle-nosed pliers to disconnect
connections as these can damage the soft metal or plastic parts of the
connectors.
▪Before working on internal components, make sure that the power is off.
Ground yourself before touching any internal components, by touching
a metal object. Static electricity can damage many of the electronic
components. Humid environments tend to have less static electricity than
dry environments. A grounding strap is warranted whenever danger of
static electricity exists.
Precautions
Computer components and electronic circuit boards can be damaged by
discharges of static electricity. Working on computers that are still connected
to a power supply can be extremely dangerous.
Follow the guidelines below to avoid damage to your computer or yourself:
▪Always disconnect the unit from the power outlet whenever you are
working inside the case.
▪If possible, wear a grounded wrist strap when you are working inside the
computer case. Alternatively, discharge any static electricity by touching
the bare metal chassis of the unit case, or the bare metal body of any
other grounded appliance.
▪Hold electronic circuit boards by the edges only. Do not touch the
components on the board unless it is necessary to do so. Don’t flex or
stress the circuit board.
▪Leave all components inside the static-proof packaging that they shipped
with until they are ready for installation.
▪Use correct screws and do not over tighten screws.