Nexgrill 720-0266 Quick reference guide

ASSEMBLY & OPERATING INSTRUCTIONS
PLEASE CONTACT 1-866-984-7455 FOR ASSISTANCE
DO NOT RETURN TO PLACE OF PURCHASE
FOR OUTDOOR USE ONLY
MODEL# 720-0266

TABLE OF CONTENTS
SECTION ONE
Importa ce………………………………1
Message to our co sumers……………2
Precautio s……………………………...3
Placeme t of the grill.……….………… 5
SECTION TWO
Assembly i structio s ………………...6
Battery Assemble………………………12
Liquid propa e Cyli der Rete tio …..13
Propa e Ta k Assemble………………13
SECTION THREE
Gas hook-up …………………………. 14
Leak testi g ……….………………..... 15
Operatio I structio s...………………16
Grill lighti g i structio …………….. ..17
SECTION FOUR
Usi g the side bur er ………………... 18
SECTION FIVE
Care a d mai te a ce ………………….18
Lighti g Illustratio ……………………….19
To match light the grill……………………20
Troubleshooti g ………………………… 21
SECTION SIX
Exploded view…………………………….22
Parts list ………………………………… .23
Orderi g parts ……………………………24
Grill hi ts ………………………………….24
SECTION SEVEN
Grill Cooki g Chart ………………………25
SECTION EIGHT
Grill recipe suggestio s …………………27
SECTION NINE
Warra ty ………………………………….30

*** WARNING ***
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
. Open lid.
4. If odor continues, immediately call your
gas supplier or your fire department.
FOR YOUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
IMPORTANCE
1

MESSAGE TO OUR CONSUMERS
Tha k you for selecti g our stai less steel gas grill.
Because this a liance contains features which may not found on other grill, we recommend that
you read this entire booklet before your first use. Kee it in handy lace as it has answers to
questions that may occur during future use.
Read this booklet carefully a d be sure your gas grill is properly assemb
led, i stalled a d mai tai ed.
Failure to follow these i structio s could result i serious bodily i jury a d/or property damage. This gas
grill i i te ded for outdoor use o ly a d is ot i te ded to be i stalled i or o recreatio al vehicles or
boats.
NOTE TO INSTALLER: Leave these i structio s with the co sumer after i stallatio .
NOTE TO CONSUMER: Retai for future refere ce.
2

WARNING
Do not try to light this a liance without first
reading the “LIGHTING INSTRUCTIONS”
section in this manual.
TESTED IN ACCORDANCE WITH ANSI
Z21.58b-2002 STANDARD FOR OUTDOOR
COOKING GAS APPLIANCES. THIS GRILL IS
FOR OUTDOOR USE ONLY.
Check your local buildi g codes for the proper
method of i stallatio . I the abse ce of local
codes, this u it should be i stalled i
accorda ce with the Natio al Fuel Gas Code
No. Z223.1-1988 a d the Natio al Electrical
Code ANSI/NFPA No. 70-1990.
CALIFORNIA PROPOSITION 65-WARNING
The bur i g of gas fuel ge erates some byproducts,
which are o the list of substa ces that are k ow by
the State of Califor ia to cause ca cer or
reproductive harm. Califor ia law requires
busi esses to war customers of pote tial exposure
to such substa ces. To mi imize exposure to these
substa ces, always operate this u it accordi g to the
use a d care ma ual, e suri g you provide good
ve tilatio whe cooki g with gas.
SAFETY PRACTICES TO AVOID PERSONAL
INJURY
Whe properly cared for, your stai less steel grill will
give safe, reliable service for ma y years. However,
extreme care must be used si ce the grill produces
i te se heat a d that ca i crease accide t pote tial.
Whe usi g this applia ce basic safety practices must
be followed, i cludi g the followi g:
Read this Care a d Use Ma ual carefully a d
completely before usi g your grill to reduce the risk of
fire, bur hazard or other i jury.
Do ot repair or replace a y part of the grill u less
specifically recomme ded i this ma ual. All other
service should be referred to a qualified tech icia .
CHILDREN SHOULD NOT BE LEFT ALONE OR
UNATTENDED IN AN AREA WHERE THE GRILL IS
BEING USED. NEVER ALLOW THEM TO SIT, STAND
OR PLAY ON OR AROUND THE GRILL AT ANY TIME.
3
The Installation of this appliance must conform
with local codes or, in the absence of local codes,
with the national fuel gas code, ANSI Z223. 1a 1988.
Installation in Canada must be in accordance with the
Standard CAN/CGA B149.1, Natural Gas Installation
Code or CAN/CGA B149.2, Propane Installation
Code and local codes.
PRECAUTIONS

PRECAUTIONS
DO NOT STORE ITEMS OF INTEREST TO
CHILDREN AROUND OR BELOW THE GRILL
OR IN THE CART. NEVER ALLOW CHILDREN
TO CRAWL INSIDE OF THE CART.
Never let clothi g, pot holders or other flammable
materials come i co tact with or too close to a y
grate, bur er or hot surface u til it has cooled.
Fabric may ig ite a d result i perso al i jury.
For perso al safety, wear proper apparel. Loose
fitti g garme ts or sleeves should ever be wor
while usi g this applia ce. Some sy thetic
fabrics are highly flammable a d should ot be
wor while cooki g.
O ly certai types of glass, heat-proof glass
ceramic, earthe ware, or other glazed ute sils
are suitable for grill use. Theses types of
materials may break with sudde temperature
cha ges. Use o ly o low or medium heat
setti gs accordi g to the ma ufacturer’s
directio s.
Do ot heat u ope ed food co tai ers as a
build-up of pressure may cause the co tai er to
burst.
Use a covered ha d whe ope i g the grill lid.
Never lea over a ope grill.
WHEN LIGHTING A BURNER, ALWAYS PAY
CLOSE ATTENTION TO WHAT YOU ARE
DOING. BE CERTAIN YOU ARE TURNING THE
IGNITER LABELED FOR THE BURNER YOU
INTEND ON USING.
When using he grill, do no ouch he grill rack,
burner gra e or immedia e surroundings as hese
areas become ex remely ho and could cause
burns. Use only dry po holders.
Moist or damp potholders o hot surfaces may
cause bur s from steam. Do ot use a towel or
bulky cloth i place or potholders. Do ot let
potholders touch hot portio s of the grill rack.
Grease is flammable. Let hot grease cool before
attempti g to ha dle it. Avoid letti g excess
grease deposits collect i the grease tray at the
bottom of the grill’s firebox. Clea ofte .
DO NOT USE ALUMINUM FOIL TO LINE THE
GRILL RACKS OR GRILL BOTTOM. This ca
severely upset combustio air flow or trap
excessive heat i the co trol area.
For proper lighti g a d performa ce of the
bur ers keep the bur er ports clea . It is
ecessary to clea them periodically for optimum
performa ce. The bur ers will o ly operate i
o e positio a d must be mou ted correctly for
safe operatio .
Clea the grill with cautio . Avoid steam bur s; do
ot use a wet spo ge or cloth to clea the grill
while it is hot. Some clea ers produce oxious
fumes or ca ig ite if applied to a hot surface.
Keep the cover of the grill closed duri g preheat
period
INSECT WARNING!!! Spiders a d i sects ca
est i the bur ers of this a d a y other grill, a d
cause the gas to flow improperly. This is a very
da gerous co ditio which ca cause a fire to
occur behi d the value pa el, thereby damagi g
the grill a d maki g it u safe to operate. I spect
the grill twice a year.
Be sure all grill co trols are tur ed off a d the grill
is cool before usi g a y type of aerosol clea er o
or arou d the grill. The chemical that produces
the sprayi g actio could, i the prese ce of heat,
ig ite or cause metal parts to corrode.
4

PRECAUTIONS
Do ot use the grill for cooki g excessively fatty
meats or products which promote flare-ups. Do
ot operate the grill u der u protected
combustible co structio . Use o ly i well
ve tilated areas. Do ot use i buildi gs,
garages, sheds, breezeways or other such
e closed areas. THIS UNIT IS FOR OUTDOOR
USE ONLY.
Keep the area surrou di g the grill free from
combustible materials, trash, or combustible
fluids a d vapors such as gasoli e or charcoal
lighter fluid. A mi imum of 24” cleara ce away
from combustible material from side a d rear
.
Do ot obstruct the flow of combustio a d
ve tilatio air. If the u it is stored i doors e sure
that it is cool. If propa e is used, the cyli der
must be u hooked a d the propa e cyli der
stored outside i a well ve tilated area, out of the
reach of childre .
DO NOT USE BRIQUETTES OF ANY KIND IN
This stai less steel grill is desig ed for optimum
performa ce without the use of briquettes. Do ot
place briquettes o the radia t as this will block off
the area for the grill bur ers to ve t. Addi g
briquettes ca damage ig itio compo e ts a d
k obs, a d void the warra ty.
Keep the back of the cart free a d clear from debris.
Keep a y electrical supply cord, or the rotisserie
motor cord away from the heated areas of the grill.
Never use the grill i extremely wi dy co ditio s. If
located i a co siste tly wi dy area (ocea fro t,
mou tai top, etc.) a wi dbreak will be required (see
below). Always adhere to the specified cleara ce.
NEVER USE A DENTED OR RUSTY PROPANE
TANK.
PLACEMENT OF THE GRILL
CLEARANCE
To Non-Combus ible Cons ruc ion
A mi imum of 3” cleara ce from the back of the
grill to o -combustible co structio is required
for the lid to ope fully.
DO NOT INSTALL THIS UNIT INTO
COMBUSTIBLE ENCLOSURES!
LOCATION
When de ermining a sui able loca ion ake in o
accoun concerns such as exposure o wind,
proximi y o raffic pa hs and keeping any gas
supply lines as shor as possible.
Locate the grill o ly i a well-ve tilated area. Never
locate the grill i a buildi g, garage, breezeway, shed
or other such e closed areas without a approved
ve tilatio system. Duri g heavy use, the grill will
produce a lot of smoke. Lock the wheels after the grill
is placed i a suitable positio accordi g to the
sticker located be eath the right door. Keep a y
electrical supply cord a d the fuel supply hose away
from a y heated surfaces. Storage of a outdoor
gas cooki g applia ce i door is permissible o ly if
the cyli der is disco ected a d removed from the
applia ce.
This outdoor cooki g gas applia ce shall be used
o ly outdoor a d shall ot be used i a buildi g,
garage or a y other e closed area. This applia ce
is ot i te ded to be i stalled o or o recreatio al
vehicles a d/or boats
5

PLEASE READ THE INSTURCTION CAREFULLY AND FOLLOW STEP BY STEP
 Propa e Ta k is ot i cluded
 Philips head Screwdriver ( ot provided)
 The followi g hardware is provided
ASSEMBLE INSTRUCTIONS
6
2pcs
1/4"
hex nut
9
16pcs
1/4"× 10mm
3
cr ossed r ound head scr ew
10pcs
1/4"
f l at washer
8
4pcs
1/4"
nut
5/ 32" 2pcs
1/4" 24pcs
washer
7
washer
45/ 32"× 10mm 2pcs
5
1/4"× 15mm 8pcs
8pcs
1/4"× 40mm
cr ossed r ound head scr ew
2
1
uant i t ySpeci f i cat i on
Descr i pt i on( SCALE 1: 1)
I t em
6
cr ossed r ound head scr ew
cr ossed r ound head scr ew

Caution: Please lock casters during installation rocess.
STEP 1:
Attach a d secure the casters with brake (A) usi g the provided truss head.
Attached wheels (B) Left cart pa el leg by removi g the hex ut screw with flat washer first a d assembli g both
wheels as show below.
STEP 2:
Attach the wire shelf to sta d-up shelf to bottom pa el use 4 pieces (1/4” x 15mm) crossed rou d head screws
a d 4 pieces of uts with flat washers.
A.
B.
7

STEP 3:
Attach both left & right pa el legs to bottom pa el with 8 pieces (1/4” x 40mm) crossed rou d head screws & 1/ 4”
washers as show i diagram.
STEP 4:
Attach fro t pa el to fro t legs of side pa els use 4 pieces (1/4” x 10mm) crossed rou d head screws & 1/4”
washers.
8

STEP 5:
Attached a d secure the cart frame cross bar to the top back of both side pa els by usi g 4 pieces (1/4” x 10 mm)
crossed rou d head screws & 1/4” washers.
STEP 6:
Place the upper portio of grill o to the assembled cart.
Caution: To avoid injury, we strongly recommend 2 or more ersons for this ste .
9

STEP 7:
Secure head u it to cart with 4 pieces (1/4” x 15mm) crossed rou d head screws & 1/4” flat washers as show i
diagram.
(Note: remove the cooki g grids before this step)
STEP 8:
Attach left side shelf with 4 pieces (1/4” x 10 mm) crossed rou d head screws & 1/4” washers as show o the
figure below.
Repeat the above step to i stall shelf o right.
10

STEP 9:
Attach a d secure the left co dime t tray to co trol pa el with o e (5/32”x10 mm) crossed rou d head screw &
5/32” washer.
Repeat the above step to i stall the co dime t tray o right side shelf.
STEP 10:
Assemble Drip pa a d Grease tray to Bowl assembly. (from rear of grill slide i to positio as show below)
11

BATTERY ASSEMBLE
1. U screw the ig itio battery cap. (Fou d at far-left of co trol pa el)
2. I sert battery i to ig itio box with the positive termi al faci g outward.
3.
Replace the ig itio
battery cap
after
the
battery
has bee i stalled
.
12

Attach regulator to prop-ta k tur i g the regulator oble, clockwise, a d by ha d u til tight as show i
figure below. LP gas cyli der must be fitted with a listed overfill preve tio device (OPD)
PROPANE TANK ASSEMBLE
LIQUID PROPANE CYLINDER RETENTION
Place liquid propa e ta k i ta k seat hole & secure with rete tio wi g-bolt.
13

GAS HOOK-UP
NEVER CONNECT AN UNREGULATED GAS
SUPPLY LINE TO THE APPLIANCE. USE THE
REGULATOR/HOSE ASSEMBLY SUPPLIED.
This is a liquid propa e co figured grill. Do ot
attempt to use a atural gas supply u less the grill
has bee reco figured for atural gas use.
Total gas co sumptio (per hour) of this stai less
steel gas grill with all bur ers o “HI”:
Mai bur er 33,000 Btu/hr.
Side bur er 12,000 Btu/hr.
Total 45,000 Btu/hr.
The i stallatio of this applia ce must co form with
local codes or, i the abse ce of local codes, with
the atio al fuel gas code, ANSI Z223. 1a-1988.
I stallatio i Ca ada must be i accorda ce with
the Sta dard CAN/CGA-B149.1, Natural Gas
I stallatio Code or CAN/CGA-B149.2, Propa e
I stallatio Code a d local codes.
L.P. TANK REQUIREMENT
A de ted or rusty L.P. ta k may be hazardous a d
should be checked by your L.P. supplier. Never use
a cyli der with a damaged valve. The L.P. gas
cyli der must be co structed a d marked i
accorda ce with the specificatio s for L.P. gas
cyli ders of the U.S. Departme t of Tra sportatio
(DOT) or the Natio al Sta dard of Ca ada,
CAN/CSA-B339, Cyli ders, Spheres a d Tubes for
Tra sportatio of Da gerous Goods; a d
Commissio , as applicable. Overfilli g preve tio
device (OPD) shall be provided o cyli der & QCCI
co ectio o the cyli der valve, ANSI/CGA-V-
1.
The cyli der supply system must be arra ge for
vapor withdrawal. The cyli der must i clude a
collar to protect the cyli der valve. The cyli der
must be provided with a shut off valve termi ati g
i a L.P. gas supply cyli der valve outlet specified,
as applicable, for co ectio type QCC1 i the
sta dard for compressed gas cyli der valve outlet
a d i let co ectio ANSI/CGA-V-1.
Ma ifold pressure: (operati g): 10” water colum
(W.C.), ( o -operati g): 11.2” water colum (W.C.).
L.P. GAS HOOK-UP
E sure that the black plastic grommets o the LP
cyli der valve are i place a d that the hose does
ot come i to co tact with the grease tray or the
grill head.
CONNECTION
Your stai less steel grill is equipped with gas
supply orifices for use o ly with liquid propa e gas.
It is also equipped with a high capacity
hose/regulator assembly for co ectio to a
sta dard 20lb. L.P. cyli der (18-1/4” high, 12-1/4”
diameter).
To co ect the L.P. gas supply cyli der, please
follow the steps below:
1. Make sure ta k valve is i its full off positio
(tur clockwise to stop)
2. Check ta k valve to assure it has proper
exter al male threads (type 1 co ectio per
ANSIZ21.81)
3. Make sure all bur er valves are i their off
positio .
4. I spect valve co ectio s, port, a d regulator
assembly. Look for a y damage or debris.
Remove a y debris. I spect hose for damage.
Never attempt to use damaged or obstructed
equipme t. See your local L.P. gas dealer for
repair.
5. Whe co ecti g regulator assembly to the
valve, ha d tighte the ut clockwise to a
complete stop. Do ot use a wre ch to
tighte . Use of a wre ch may damage the
quick coupli g ut a d result i a hazardous
co ditio .
6. Ope the ta k valve fully (cou terclockwise).
Use a soapy water solutio to check all
co ectio s for leaks before attempti g to
light the grill, see below. If a leak is fou d, tur
the ta k valve off a d do ot use the grill u til
a local L.P. gas dealer ca make repairs.
14

To disconnect L.P. gas cylinder:
1. Tur the bur er valves off.
2. Tur the ta k valve off fully (tur clockwise
to stop).
3. Detach the regulator assembly from the
ta k valve by tur i g the quick coupli g ut
cou terclockwise.
LEAK TEST
Check all gas su ly fittings for leaks before
each use. It is handy to kee a s ray bottle of
soa y water near the shut-off valve of the gas
su ly line. S ray all the fittings. Bubbles
indicate leaks.
Disconnected L.P. cylinders must have
threaded valve lugs tightly installed, and
must not be stored in a building, garage or
any other enclosed area.
The gas must be turned off at the su ly
cylinder when the unit is not in use.
If the a liance is stored indoors the cylinder
must be disconnected and removed from the
a liance. Cylinders must be stored outdoors
in a well-ventilated area out of the reach of
children.
GAS FLOW CHECK
Each grill bur er is tested a d adjusted at the
factory prior to shipme t; however, variatio s i
the local gas supply may make it ecessary to
adjust the bur ers. The flames of the bur ers
should be visually checked.
Flames should be blue a d stable with o
yellow tips, excessive oise or lifti g. If a y of
these co ditio s exist, check to see if the air
shutter or bur er ports are blocked by dirt,
debris, spider webs, etc. If you have a y
questio s regardi g flame stability, please call
customer service 1-866-984-7455
ALWAYS CHECK FOR LEAKS AFTER
EVERY L.P. TANK CHANGE
INSTALLER FINAL CHECK LIST
 S ecified clearance maintained 24” from
combustibles.
 All internal ackaging removed.
 Knobs turn freely.
 Burners are tight and sitting ro erly on
orifices.
 Pressure regulator connected and set for
11.2” W.C. L.P. gas. Gas connections to grill
using hose & regulator assembly rovided
( re-set for 11.0” water column).
 Unit tested and free of leaks.
 User informed of gas supply shut off valve
location
USER, PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PROPANE CYLINDER CAUTIONS
a) Do Not store a s are LP-gas cylinder
under or near this a liance.
b) NEVER fill the cylinder beyond 80 ercent
full.
c) If the information in “a” and “b” is not
followed exactly, a fire causing death or
serious injury may occur.
15

OPERATING INSTRUCTIONS
GENERAL USE OF THE GRILL
Each main burner is rated at 11,000 Btu/hr. The
main grill burners encompass the entire cooking
area and are side ported to minimize blockage from
falling grease and debris. Above the burners are
stainless steel radiants flame covers). The igniter
knobs are located on the lower center portion of the
valve panel. Each rotary igniter is labeled on the
control panel.
USING THE GRILL
Grilling requires high heat for searing and proper
browning. Most foods are cooked at the “HI” heat
setting for the entire cooking time. However, when
grilling large pieces of meat or poultry, it may be
necessary to turn the heat to a lower setting after
the initial browning. This cooks the food through
without burning the outside. Foods cooked for a
long time or foods basted with a sugary marinade
may need a lower heat setting near the end of the
cooking time.
NOTE: This stainless steel grill is designed to grill
efficiently without the use of lava rocks or briquettes
of any kind. Heat is radiated by the stainless steel
flame tamers positioned above each burner.
DO NOT LEAVE THE GRILL UNATTENDED
WHILE COOKING.
NOTE: The hot grill sears the food, sealing in the
juices. The longer the preheat, the faster the
meat browns and the darker the grill marks.
16

GRILL LIGHTING INSTRUCTIONS
WARNING: IMPORTANT!
BEFORE LIGHTING…
Inspect the gas supply hose prior to turning the gas
“ON”. If there is evidence of cuts, wear, or abrasion, it
must be replaced prior to use. Do not use the grill if
the odor of gas is present. Only the pressure
regulator and hose assembly supplied with the unit
should be used. Never substitute regulators for those
supplied with the grill. If a replacement is necessary,
contact the factory for proper replacement.
Screw the regulator type QCC1) onto the tank. Leak
check the hose and regulator connections with a
soap and water solution before operating the grill.
TO LIGHT THE GRILL BURNER:
Make sure all knobs are “OFF” then turn on the gas
supply from the LP tank. Always keep your face and
body as far from the grill as possible when lighting.
Your stainless steel grill has an exclusive patented
built-in ignition. The igniter is built in to the valve. To
ignite each burner simply push and turn the control
knobs to the HI setting, you will hear the valve click
as it sends a spark to the pilot flame. If the burner
does not light wait 5 minutes for any excess gas to
dissipate and then retry.
FLAME CHARACTERISTICS
Check for proper burner flame characteristics. Each
burner is adjusted prior to shipment; however,
variations in the local gas supply may take minor
adjustments necessary.
Burner flames should be blue and stable with no
yellow tips, excessive noise, or lifting. If any of these
conditions exist call our customer service line. If the
flame is yellow, it indicates insufficient air. If the flame
is noisy and tends to lift away from the burner, it
indicates too much air.
TO MATCH LIGHT THE GRILL
If the burner will not light after several attempts then
the burner can be match lit.
Lighting rod-Here is your instruction:
Match light extension rod
Use this device to match light your burners
Simply place a lighted match between the coils on
the end of the extension rod and hold next to the
burner to ignite. see reference Pg)
If you’ve just attempted to light the burner with the
igniter, allow 5 minutes for any accumulated gas to
dissipate. Keep your face and hands as far away
from the grill as possible. Insert a lit match attached
to tight lighting rod or lighter through the cooking
grids to the burner. see next page) Press the control
knob and rotate left to the HI setting, continue to
press the knob until the burner ignites. Burner should
light immediately. If the burner does not light in 4
seconds turn the knob off, wait 5 minutes and try
again.
Keep a spray bottle of soapy water near the gas
supply valve and check the connections before
each use.
Do not attempt to light the grill if odor of gas is
present. Call for service 1
-
866
-
984
-
7455
17
Approximate 1 1/2 “ Flame Height

USING SIDE BURNER
WARNING: IMPORTANT!
USING THE SIDE BURNER:
Inspect the gas supply hose prior to turning the gas
“ON”. If there is evidence of cuts, wear or abrasion, it
must be replaced prior to use. Do not use the side
burner if the odor of gas is present. WARNING:
Always keep your face and body as far away from
the burner as possible when lighting.
LIGHTING INSTRUCTIONS
To light the side burner, remove any cooking utensils
from the burner grate. Push and turn the control knob
counterclockwise to the “HI” position. If the burner
does not light, turn the control knob to “OFF”. If the
smell of gas is detected and the igniter is not
functioning, immediately turn the control knob “OFF”.
Allow 5 minutes for any accumulated gas to
dissipate.
If the side burner igniter is not functioning, see the
following section for match lighting.
MATCH LIGHTING
Hold a lit extended match or lighter near the side
burner ports, turn the control knob counterclockwise to
“HI”. Move your hand immediately once the burner is lit.
Rotate the control knob to the desired setting.
Burner flames should be blue and stable with no yellow
tips, excessive noise, or lifting. If any of these
conditions exist call our customer service line. If the
flame is yellow, it indicates insufficient air. If the flame is
noisy and tends to lift away from the burner, it indicates
too much air.
CARE AND MAINTENANCE
STAINLESS STEEL
The grill is made from non-rusting and non-magnetic
stainless steel. There are many different stainless
steel cleaners available. Always use the mildest
cleaning procedure first, scrubbing in the direction of
the grain. To touch up noticeable scratches in the
stainless steel, sand very lightly with dry 100 grit
emery paper in the direction of the grain. Specks of
grease can gather on the surfaces of the stainless
steel and bake on to the surface and give the
appearance of rust. For removal use an abrasive pad
in conjunction with a stainless steel cleaner.
GRILL RACK
The easiest way to clean the grill is immediately after
cooking is completed and after turning off the flame.
Wear a barbeque mitt to protect your hand from the
heat and steam. Dip a brass bristle barbeque brush in
tap water and scrub the hot grill. Dip the brush
frequently in the bowl of water. Steam, created as
water contacts the hot grill, assists the cleaning
process by softening any food particles. The food
particles will fall and burn. If the grill is allowed to cool
before cleaning, cleaning will be more difficult.
ENSURE THAT THE GAS SUPPLY AND THE KNOBS
ARE IN THE “OFF” POSITION. MAKE SURE THE
RANGETOP BURNER IS COOL BEFORE REMOVAL.
GRILL BURNERS
Extreme care should be taken when moving a burner as
it must be correctly centered on the orifice before any
attempt is made to relight the grill. Frequency of cleaning
will depend on how often you use the grill.
MAIN GRILL BURNER CLEANING
Ensure the gas supply is off and the knobs are in the
“OFF” position. Make sure the grill is cool. Clean the
exterior of the burner with a wire brush. Clear stubborn
scale with a metal scraper. Clear any clogged ports with
a straightened paper clip. Never use a wooden toothpick
as it may break off and clog the port. Please note if
insects or other obstructions are blocking the flow of gas
through the burner, and if so you will need to call our
customer service line.
GREASE TRAY CLEANING:
The grease tray should be emptied and wiped down after
each use and washed in a mild detergent and warm
water solution.
18