Nexus 1000 User manual

Owner’s Assembly And Operating Manual
Ultra Light Plus, Full Electric Low Bed
Nexus 1000
Item # 15235

1. Conrmthatallpartsarepresent.
 A.FootSpring
 B. HeadSpring
 C. HeadBoard
 D. FootBoard
 E. Hi/LowShaft
 F. LockingPins
 G. Motor
 H. HandCrank(attachedtofootboardforshipping)
 I. Casters(4)-2locking,2non-locking
 J. SpringClips(2)
 K. HandPendant
 L. FullElectricMotor
Assembly Instructions
AB
C
D
E
F
G
H
IJ
K
L

Assembly Instructions Cont.
2. Connecttheheadspringbyaligningwithfootspringandswingingbothendsawayfromeachother.
3. Optional:Insertlockpinthroughconnected
 sleepsurfaceandsecurewithspringclip.

Assembly Instructions Cont.
6. Slidelockcollar1/4”fromthefoot
 sideofthehangerbracketasshown.
 Tightenthumbscrew.
5. InstallHi/LowshafttotheHi/Low
 motoratthefootsectionofthebed
 byinsertingthespringloadedside
 oftheshafttothebottomreceptacle
 asshown.
1/4”Gap
ThumbScrew
SpringLoadedShaft
4. Placethefootspringstandingupontheoor
 onitsside.SlideHi/Lowshaftthroughhanger
 bracket.
HangerBracket

Assembly Instructions Cont.
7. Hi/LowshaftconnectedtoHi/Lowmotor.
9. Installthecastersbyinsertingthe
 stemofthecasterintotheleg
 receptacle.Itisrecommendedto
 install1lockingcasterand1non-
 lockingcasteroneachbedend.
 Thelockingcastersshouldbe
 installeddiagonallyfromeachother.
8. Connectheadsectionandfootsection
 bysqueezingtogetherandattaching
 withspringlinks.Pullupthehead
 sectionandfootsectiontorelease
 tensionbetweenthesprings.
StemLegReceptacle

Assembly Instructions Cont.
10. Withbedonsideextendtheshaftuntilit
 reachesthefulllengthofbed.
a. NOTE:Theshaftadjustmentholesare
 markedtoindicatethestyle(semi/full)ofbed
 theshaftisbeinginstalledon.
11. Attachtheheadboardandfootboard
 asshown.
a. NOTE:Theheadsectionishigherthan
 thefootsection.However,theyare
 interchangeablewitheachother,withall
 otherDriveandothermanufacturers
 headandfootboards.

Assembly Instructions Cont.
12.Installtheheadendoftheshaftas
 shown.
13. Releasethespringloadedshafton
 thehi/lowmotorandinserttheshaft
 intothegearboxonthefootboard.
14. Makesuretheslotonthespring
 loadedshaftengagestherollpinon
 thegearbox.

NOTE:Beforeinstallingmotor,plughand
pendantandHi/Lowmotorcableintomotor
asshown
14.Connectthe9Vbattery(soldseparately)tothe
 batterycliponthemotor.Itisstoredintherecess
 underthemotorcover.Withthisbatteryinstalled,
 themotorcanbeoperatedintheeventofapower
 failure.
15. Toinstallmotor,removelockingcapsontopof
 themotor.
Motor Installation
HAND CONTROL
TheCompetitorbedcomeswithahandcontrolthatwill
illuminatewhenthebedispluggedintoagroundedor
polarizedwalloutlet,orwith9Vbattery(soldseparately)
installedinthehandcontrol.Thehandcontrolwill
illuminateaslongasthewallorbatteryhaspower.With
thisbatteryinstalled,themotorcanbeoperatedtoreturn
thesleepsurfacetothehorizontalpositionintheeventof
apowerfailure.

Motor Installation Cont.
16. Alignthemotorwiththeactuatorbar
 andlifttheheadspringtothehighest
 position.Themotorwillautomatically
 bepulledtowardsthebedandlock
 ontotheaccuator.Repeatforfoot
 section.
17.Afterthemotorisinstalled,slide
 lockingcoversbackonmotor.
ActuatorBar

Bed Rail Installation
18. AttachingBedRails
b. FullRails
• Thefootandheadsectionhavecolor
 codedsprings,labelsandnotchesinthe
 frame.
• Installthecrossbracebetweentheblack
 springsforproperrailplacement.
a. Halfrails
• Theheadsectionfeatureslabelsonthe
 framemarked,“AttachHalfRailsHere”
 andblackspringsforproperplacement.