NexWatch PW-5000 User manual

PW-5000
Single Reader Enclosure
Installation Guide
Part Number: PW5K1ENC4
WARNINGS AND CAUTIONS
WARNING
Before installation, turn off the external circuit breaker which supplies power to the system.
Before connecting the device to the power supply, verify that the output voltage is within specifications of the power supply.
Do not apply power to the system until after the installation has been completed. Personal injury or death could occur, and the equipment
could be damaged beyond repair if these WARNINGS are not observed!
Fire Safety and Liability Notice
Never connect card readers to any critical entry, exit door, barrier, elevator or gate without providing an alternative exit in accordance with
all fire and life safety codes pertinent to the installation. These fire and safety codes vary from city to city and you must get approval from
local fire officials whenever using an electronic product to control a door or other barrier. Use of egress buttons, for example, may be illegal
in some cities. In most applications, single action exit without prior knowledge of what to do is a life safety requirement. Always make cer-
tain that any required approvals are obtained in writing. DO NOT ACCEPT VERBAL APPROVALS, THEY ARE NOT VALID.
NexWatch never recommends using the PW-5000 Series or related products for use as a primary warning or monitoring system. Primary
warning or monitoring systems should always meet local fire and safety code requirements. The installer must also test the system on a regu-
lar basis and instruct the end user in appropriate daily testing procedures. Failure to test a system regularly could make installer liable to the
end user for damages if a problem occurs.
WARNING
EARTH ground all enclosures, for proper installation.
WARNING
Use suppressors on all door strikes. Use S-4 suppressors for installation. NexWatch recommends only DC strikes.
CAUTION
IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST BE FILED WITH THE COMMERCIAL CARRIER RESPONSIBLE.
CAUTION
Electro-static discharge can damage CMOS integrated circuits and modules.
To prevent damage always follow these procedures:
Use static shield packaging and containers to transport all electronic components, including completed reader assemblies.
Handle all ESD sensitive components at an approved static controlled workstation. These workstations consist of a desk mat, floor mat and
an ESD wrist strap. Workstations are available from various vendors.
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules when
wired using metal conduit for the cabling external to the enclosure. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference that will require correcting at the users expense.
NOTICE
This document and the data in it shall not be duplicated, used or disclosed to others for procurement or manufacture, except as authorized
by and with the written permission of, NexWatch. The information contained in this document or in the product itself is considered the exclu-
sive property and trade secrets of NexWatch. Copyright laws of the United States protect all information in this document or in the software
product itself.
The information is this document is subject to change without notice.
TD1126rev1101

NOTICE
Any use of this product is subject to the terms and acceptance of the NexWatch Software Agreement. Please request a copy from NexWatch,
and review the agreement carefully.
DISCLAIMER
PRODUCT LIABILITY / MUTUAL INDEMNIFICATION
In the event that a Customer receives a claim that a Product or any component thereof has caused personal injury or damage to property of
others, Customer shall immediately notify NexWatch in writing of all such claims. NexWatch shall defend or settle such claims and shall indem-
nify and hold Customer harmless for any costs or damages including reasonable attorneys’ fees which Customer may be required to pay as a
result of the defective Product or the negligence of NexWatch, its agents, or its employees.
Customer shall hold harmless and indemnify NexWatch from and against all claims, demands, losses and liability arising out of damage to
property or injury to persons occasioned by or in connection with the acts or omissions of Customer and its agents and employees, and from
and against all claims, demands, losses and liability for costs of fees, including reasonable attorneys’ fees, in connection therewith.
UNPACKING PROCEDURE
CAUTION
If any damage to the shipment is noticed before unpacking, a claim must be filed with the commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to the contents.
The following steps are used to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the container and all packing materials. They may be used again
for reshipment of the equipment, if needed.
2. Inspect the contents for shortage. If items are missing, contact the order entry department at 800-227-1667 Option-2.
3. Visually check contents. If damage is discovered, perform the following:
• If shipping caused damage to the unit, a claim must be filed with the commercial carrier.
• If any other defect is apparent, call 800-227-1667 Option-2 for a return authorization.
SHIPPING INSTRUCTIONS
To ship equipment back to NexWatch:
1. Contact the customer service department at 800-227-1667 Option-2 before returning equipment. When calling, please have available:
• A description of the problem or reason for returning the equipment.
• Original purchase order number, invoice number and whether or not the unit is still under warranty.
• A new purchase order number if the unit is not under warranty.
2. Obtain the Return Authorization Number (RMA) from the customer service department.
3. Show the RMA number on all packages shipped. Packages not marked with an RMA number will be refused at the factory and returned
COD.
4. Carefully pack the equipment for shipment. Use the original packing material whenever possible.
LIMITED WARRANTY
All Products sold or licensed by NexWatch include a warranty registration card which must be completed and returned to NexWatch by or on
behalf of the end user in order for NexWatch to provide warranty service, repair, credit or exchange. All warranty work shall be handled through
the Customer which shall notify NexWatch and apply for a Return Merchandise Authorization (RMA) number prior to returning any Product for
service, repair, credit or exchange. NexWatch warrants that its Products shall be free from defects in materials and workmanship for a period of
two years from date of shipment of the Product to Customer. The warranty on Terminals, Printers, Communications Products and Upgrade kits
is 90 days from date of shipment. Satisfaction of this warranty shall be limited to repair or replacement of Products which are defective or defec-
tive under normal use. NexWatch’ warranty shall not extend to any product which, upon examination, is determined to be defective as a result of
misuse, improper storage, incorrect installation, operation or maintenance, alteration, modification, accident or unusual deterioration of the
Product due to physical environments in excess of the limits set forth in Product manuals. THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THIS PROVISION. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. NO REPRESENTATION OR
WARRANTY OF THE DISTRIBUTOR SHALL EXTEND THE LIABILITY OR RESPONSIBILITY OF THE MANUFACTURER BEYOND THE
TERMS OF THIS PROVISION. IN NO EVENT SHALL NEXWATCH BE LIABLE FOR ANY RE-PROCUREMENT COSTS, LOSS OF PROFITS,
LOSS OF USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES TO ANY PERSON RESULTING FROM THE USE OF NEXWATCH’
PRODUCTS.
CONFIDENTIALITY
All software, drawings, diagrams, specifications, catalogs, literature, manuals and other materials furnished by NexWatch relating to the design,
use and service of the Products shall remain confidential and shall constitute proprietary rights of NexWatch and Customer agrees to treat such
information as confidential. Customer shall acquire no rights in the design of the Products or the related materials except to use such information
solely for the purpose of and only during the time it sells the Products. Customer shall not copy the design of any of the Products or use or cause
to be used any Product design or related materials for its own benefit or for the benefit of any other party. The covenants contained in this section
shall remain effective throughout the term of this Agreement and thereafter unless specifically waived by NexWatch in writing.
PW-5000 Enclosure - PW5K1ENC4 Installation Guide 2

DIMENSIONS
Height: 8.375" (21.275cm) Width: 7.625" (19.4cm) Color: Grey
Depth: 7.625" (19.4cm) Metal thickness: .05" (.127cm)
Installation holes: Single ended hanging slots for mounting the cabinet in the
upright position. The 3 hangers are in a triangular pattern. The top two are
located .75" (1.9cm) from the top and spaced 6.125" (15.5cm) apart. The lower
hanger is located .930" (2.36cm) from the bottom and 7.85" (19.9cm) from
each edge. See Enclosure Drawing.
Dual Conduit Knockouts: ½" & 1" (1.27cm x 2.54cm)
Top Side: 1
Bottom Side: 0
Right Side: 1
Left Side: 2
Rear Side: 1
POWER SUPPLY
DO NOT USE POWER SUPPLY TO POWER LOCKS.
PRO22E4PS:12 VDC 1.2 amp continuos power limited output with backup
battery charging. 16.5 VAC 20va wall transformer provided.
Requires 115 VAC/60hz, Maximum battery charge current .5amp
AC on LED
Short circuit and thermal overload protection
All power connection should be made with 18ga or larger wiring
LED DIAGNOSTICS
AC LED DC LED
ON ON Normal operating conditions
OFF ON Loss of AC, standby battery supplying power
ON OFF No DC output
OFF OFF Loss of AC, Discharged or no Stand-by battery.
No DC output.
BACKUP POWER SUPPLY
Automatic Switch over to stand-by battery when AC fails (zero voltage drop)
4.0 AH sealed rechargeable battery
Backup time: 2.5 to 4 hour depending on configuration
CABLES SUPPLIED
Power On Light assembly
Tamper Switch assembly
MAINTENANCE
Replace the 12V 4AH battery every 2 to 2.5 years
Oil the hinges on the door every 12 months
OPERATING PARAMETERS
Temperature: 35 to 110 C (2 to 43 C)
Operating Humidity: Up to 85% non-condensing
INSTALLATION INSTRUCTIONS
1. Remove the 16.5V 20VA wall transformer, battery and parts bag from the
enclosure.
2. Add all eight plastic standoffs into the mounting holes forming an upper and
lower square.
3. Measure and install the top two mounting screws with heads smaller than .4"
using proper mounting techniques for the material being used to hold the
PW5K1ENC4. Space the screws 6 1/8" apart. Leave the screws exposed
approximately 1/2".
4. Open the door of the enclosure and place the hanging slots over the mounting
screws. Push the enclosure over the mounting screws and allow the screws to
slide into the slots. Finish tightening the mounting screws to securely hold the
enclosure. Screw in the lower hanger to secure the enclosure against the wall.
5. Install the tamper switch cable to the bottom two screws on the tamper switch.
Slide the tamper switch holder onto the upper right corner of the enclosure.
Push the tamper switch cable and the tamper switch through the center hole of
the tamper switch holder.
6. Mount the Power on Light assembly to the enclosure by passing the wire ends
from the outside to the inside of the enclosure through the ¼" hole located on
the upper right side of the enclosure. Secure the Power on Light by sliding the
retaining ring over the wires and onto the light holding it snug to the wall of the
enclosure.
7. Run all appropriate wiring to the case. Mark each wire as to the panel, location
and input type. All cable shields should tie to the grounding stud found on the
upper left side of the enclosure.
8. Install the single reader panel onto the 4 standoffs in the bottom left of the
enclosure, placing the power and communications to the top.
9. Wire the readers, input and output connections by removing the terminals for
ease of wiring. Wire according to installation guide supplied with the single
reader panel.
10. CHECK ALL CONNECTIONS PRIOR TO POWERING UP THE ENCLOSURE
AND PANELS.
11. Mount the power supply to the 4 standoffs at the upper right of the enclosure.
Place the terminal strip to the right. Connect the two supplied battery cables:
RED to Batt+, BLACK to Batt-. Wire the power supply through the wall
transformer provided. Connect to the AC terminals. Wire the Power on Light to
the AC in connections on the power supply. Plug in the Wall transformer. The
Power on Light should light. Check the voltage at ±DC. The voltage should be
approximately 13.8 VDC.
12. Disconnect the power.
13. Connect the DC power to the panel. Insure that the connection has the correct
polarity. Follow the wiring diagram supplied with the panels.
14. Connect the Tamper Switch cable to the two pin connector "9" located on the
mid right of the panel. See individual panel wiring diagrams supplied with the
panel.
15. Connect Communications wiring per the wiring diagram supplied with the panel.
16. Place the 12V 4AH battery in the cabinet on the bottom right hand side. Attach
the red battery charging connection to the positive terminal of the battery and
the black battery charging connection to the negative connection of the battery.
17. CHECK ALL CONNECTIONS PRIOR TO POWERING UP THE ENCLOSURE
AND PANELS.
PW-5000 Enclosure - PW5K1ENC4 Installation Guide 3

CABLE SPECIFICATIONS
Application NCI Part No. AWG Description Max. Dist. Imp. Cap.
N-485 connections NC2442-TN N/A Belden 9842 4000' (1200 m) 120W 12.8pf/ft
N/A or equivalent
Readers/Keypads with NC1861-BL 18 6 conductor shielded 500' (152 m)
Wiegand style INTERFACE
Alarm input points NC 2221-BR 22 2000' (610 m)
Relay outputs NC 1821-OR 18 twisted pair, shielded 2000' (610 m)
Note: For plenum rated cable just add a “P” to Engineered Systems' NC part number prefix; for example NC1861-BL becomes NCP1861-BL.
NCI CABLE PART NUMBERS
Part Number Description Application Length
NC1841-GY 18 AWG/4 conductor reader cable 1,000' (304.8m)
NC1861-BL-500 18 AWG/6 conductor reader cable 500' (152m)
NC1861-BL 18 AWG/6 conductor reader cable 1,000' (304.8m)
NC18121-YL-500 18 AWG/12 conductor keypad cable 500' (152m)
NC18121-YL 18 AWG/12 conductor keypad cable 1,000' (304.8m)
NCNET-1 50 Ωnetwork cable 1,000' (304.8m)
NC2221-BR 22 AWG/2 conductor alarm cable 1,000' (304.8m)
NC1821-OR 18 AWG/2 conductor power/door cable 1,000' (304.8m)
NCC59206-BK RG-59 video cable 1,000' (304.8m)
NCP1841-GY 18 AWG/4 conductor Plenum reader cable 1,000' (304.8m)
NCP1861-BL-500 18 AWG/6 conductor Plenum reader cable 500' (152m)
NCP1861-BL 18AWG/6 conductor Plenum reader cable 1,000' (304.8m)
NCP18121-YL 18 AWG/12 conductor Plenum keypad cable 1,000' (304.8m)
NCP18121-YL-500 18 AWG/12 conductor Plenum keypad cable 500' (152m)
NCPNET-1 50ΩPlenum network cable 1,000' (304.8m)
NCP2221-BR 22 AWG/2 conductor Plenum alarm point cable 1,000' (304.8m)
NCP1821-OR 8 AWG/2 conductor Plenum power/door cable 1,000' (304.8m)
NC2442-TN 24 AWG/120 Ω12.8pf RS485 wire communication cable 1,000' (304.8m)
NCP2442-TN 24 AWG/120 Ω12.8pf Plenum communication cable 1,000' (304.8m)
PW-5000 Enclosure - PW5K1ENC4 Installation Guide 4
Your Access to the Future
47102 Mission Falls Court • Fremont, CA 94539 USA • Tel: [phone] Fax: [phone] • www.nexwatch.com