Tyco Electronics 58241-1 User manual
E
!
! " "#$
$ $%&'
($%&' $ $ % % $ # )'
+, !!+ +" -./.0.----
"12 +3"4!+ -./.5.605 $ $% 7 '
3 # $ " % #
# )
- 3 "#
!" !"
#$%#$ & '&()*(+
%#%1$% $% )$$'$ $$ $) #%
' ! )$ )$ 8% 9$$. $ #'
(+$%)&,(%+
$
4
#
%%* ( ! !! !
1
:49; --'<= >'<5? -<'5= >'50? /'=/ >'==?
$ 0-5. 0-5. -/6=.-
4'
=-=-/=.- =-=-/=.- ...
@#
! =-=-6.- =-=-6. =-=-6.=
Figure 1
! (+$%)&,(%+
This instruction sheet covers use and maintenance of
Shielding Enclosure Expansion Tool Kits 58241–1,
58241–2, and 58241–4. These tools are used to
expand the cable outlet of shielding enclosures for
AMPLIMITE* connectors, allowing the enclosure to be
inserted easily over cable.
! "#
$% & ' &' !
& &
Read these instructions thoroughly before using the
cover extraction tool.
Reasons for reissue of this instruction sheet are
provided in Section 5, REVISION SUMMARY.
Figure 2
%
4$ 9
4
A&
(%
)
(%
9
B C)
3 $
3 C)
+%
i
Figure 3
Step 1 Step 3
Step 4Step 2
!"#$#%&
!"
The tools feature a metal plunger and sliding sleeve.
There is a pin in the plunger shaft that limits how far
the plunger can extend past the end of the sleeve.
The plunger shaft is threaded to receive a plastic
handle, or to be used with a bench mounting plate.
The handle and mounting plate are included in the kit.
The threaded end of the plunger is flat on both sides
so that it can also be mounted in a vise. Figure 2
shows typical bench and vise mountings.
'#&( ) %%*
Figure 3 shows the steps for using the tool. Steps are
the same whether tool is hand held or mounted. Make
sure tool and cable diameter are compatible
according to the table in Figure 1. Then:
1. Insert extended tool tip and sleeve through
cable opening of shielding enclosure.
2. Retract tool tip into sleeve.
3. Insert cable end into sleeve. Hold enclosure in
position on cable, and remove tool from the
enclosure.
4. Carefully slide cable through enclosure so that
enough cable protrudes to apply the connector and
shielding. Instruction sheet 408–9172 covers
connector application procedures; and 408–9218
covers shielding.
+ ,-#&-#&#&( ) %%*
Inspect the tool when you receive it and occasionally
thereafter. When not in use, store tool in a clean, dry
area. If parts are lost or damaged, refer to Figure 1
for the correct part numbers, and order replacements
from:
CUSTOMER SERVICE (38–35)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105–3608
For tool repair service, please contact a Tyco
Electronics representative at 1–800–526–5136.
. "/##%& ',,-"0
Since the previous release of this sheet, the following
changes were made:
S
Updated document to corporate requirements
This manual suits for next models
2
Other Tyco Electronics Enclosure manuals
Popular Enclosure manuals by other brands
Siemens
Siemens CERBERUS PYROTRONICS ALI-8 installation instructions
Thermaltake
Thermaltake Urban S31 Series user manual
Caselabs
Caselabs magnum tx10 Assembly manual
Extron electronics
Extron electronics HSA 400 Series installation guide
SilverStone
SilverStone RAVEN RVS02 manual
cable matters
cable matters 201079 user manual
