Nidec AA28438000 User manual

Manual Package
This package was recreated in 2019.
Serial Number: 22765
Note: This package includes drawings and
manuals which pertain to the original manufacture
of this equipment. Modications implemented
after shipment from Kato Engineering are
not represented in this documentation and
are not supported by Kato Engineering.
Kato Engineering, Inc. |P.O. Box 8447 |Mankato, MN USA 56002-8447 | Tel: [phone]
[email protected] |www.KatoEngineering.com |Fax: [phone]

Vibration - Condition Monitoring
and Protection www.metrix1.com • [email protected]
Sales & Service Tel: [phone] • Fax: [phone] • REV A
PROXIMITY PRODUCTS
Proximity Probe Transmitter
This new Trendsetter transmitter is a 2-wire loop-
powered transmitter combining an eddy current
probe driver and a signal conditioner in a single
package. It provides a 4-20 mA output proportional
to overall peak to peak displacement and operates
with Metrix probes and extension cables as well as
4 major probe systems. A DC voltage output and
dynamic signal is available at the BNC connector.
The TXR Transmitter is designed for radial
vibration while the TXATransmitter is designed for
axial position vibration.
Features
• Cost effective alternative to
dedicated rack mount monitors
• Loop-powered driver/transmitter
• Compatible with 4 major probe systems
• Easily factory calibrated to non-standard
shaft material
• DIN Rail mounting (flat mounting base
available) (P/N 9647)
• BNC for access to dynamic output and
probe gap
• PBT plastic material
Machines using Shaft Monitoring
• Oil lubricated fluid film bearing machines:
-Centrifugal Pumps
-Turbo Compressors
-Steam and Gas Turbines
-Large Fans and Blowers
-Gear Box Shafts
-Generators
-Large Electric Motors
Specifications
Unless otherwise noted, all specifications are
specified at 21°C (70°F), +24 Vdc power
supply, gap set to 1.27 mm (50 mils) and
using Metrix AISI 4140 steel target.
Operating Temperature Range:
-40°C to 85°C (-40°F to 185°F)
Operating Humidity Range:
95% non-condensing, external environmental
protection is required
Power Requirements:
• 17 to 30 VDC with a maximum start
up current of 23 mA (-40°C to 85°C)
• Maximum loop resistance is
determined by RL= 50 (Vs-17) ohms
Frequency Response:
• 5 Hz to 5 kHz +0, -3 dB pk-pk
vibration
• 0 Hz to 20 Hz +0, -3 dB position
Linear Range:
• 0.5 to 2.0 mm (20 to 80 mils);
(8 mm probe)
• 0.5 to 4.0 mm (20 to 160 mils);
(11 mm probe)
Buffered Output:
• 7.87 V/mm (200 mV/mil) +/- 5% when
calibrated as a system, +/- 12%
including interchangeability error when
measured in 0.25 mm (10 mils)
increments over linear range
• 3.94 V/mm (100 mV/mil) +/- 5% for
11 mm probes when calibrated as a
system, +/- 12% including
interchangeability error when measured
in 0.25 mm (10 mils) increments over the
linear range
• 0 Hz to 3 kHz +0, -3 dB
Note: The buffered output is intended for local
diagnostics only and will not support loads that
are less than 100k ohms.
4-20 mA Output:
• 4 mA +/- .1 mA with no input
vibration
• 4 mA +/- .2 mA @ -40°C to 85°C
with no input vibration
• 20 mA +/- .5 mA @ -40°C to 85°C
with full scale input vibration
• < 3.6 mA indicates “Not OK”
condition
Trendsetter Model TXR (Radial) and TXA (Axial)
1.20

www.metrix1.com • [email protected]
Sales & Service Tel: [phone] • Fax: [phone] • REV A
Vibration - Condition Monitoring
and Protection
PROXIMITY PRODUCTS
Trendsetter will support the following probes:
• 10000 and 7200 series probes with 5, 8 or 11
mm tips and 5 or 9 meter system lengths
• 3300 series probes with 5, 8 or 11 mm tips and
5 or 9 meter system lengths
• RAM series probes with 5 mm tips and 5 or 7
meter system lengths
• 3000 series probes with 0.190 or 0.300 in. tips
and 15 or 20 foot system lengths
Supply Voltage: 17 to 30 VDC
Maximum Loop Resistance: RL = 50 (Vs-17) ohms
Terminal Block:
• Two piece, removable terminal block, for ease
of installation
• Accepts 16 to 28 AWG wire
Product Inputs:
Product Outputs:
4-20 mA proportional to Shaft relative vibration or Shaft
Position:
Vibration (TXR):
• 0-3 mils, 0-75 um pk-pk
• 0-5 mils, 0-125 um pk-pk
• 0-10 mils, 0-250 um pk-pk
Position (TXA):
• 20-80 mils, 0.5-2.0 mm; (5 mm, 8mm, 0.190 in.
and 0.300 in. probe)
• 20-160 mils, 0.5-4.0 mm; (11 mm probe)
Not OK indication: A not OK condition is normally caused
by an open probe coil or cable, probe gap outside the
linear range or supply voltage below 16Vdc. The TXR and
TXA output will be < 3.6 mA under the above conditions.
Proximity Probe Transmitter
Trendsetter Model TXR (Radial) and TXA (Axial)
Weight & Dimensions
(P/N 9647)
1.21
Weight = 0.6 pounds
Hazardous Area Ratings:
• CSA Certified: Intrinsically Safe Class
I, Div 1, Grps A, B, C & D, Temp
Code T4.
•CSA Certified: Non-Incendive Class
I, Div 2, Grps A, B, C & D
•BASEEFA Certified: Intrinsically Safe Ex
ia IIC T4, Non-Incendive Ex ia IIC T4
Specifications (continued)

Vibration - Condition Monitoring
and Protection www.metrix1.com • [email protected]
Sales & Service Tel: [phone] • Fax: [phone] • REV A
PROXIMITY PRODUCTS
Proximity Probe Transmitter
Trendsetter Model TXR (Radial) and TXA (Axial)
How to Select
TXR 33
-
Probe Series
-
System
Length Tip
Diameter
5 5 meters
99 meters
05&8 mm
or
TXA 33
-
Probe Series
-
System
Length Tip
Diameter 4-20 mA Range*
5 5 meters
99 meters 0 5&8 mm 0 20 to 80 mils
or
For Series 3300 & 3300 XL
For Series 10000 and 7200
TXR 72
-
Probe Series
-
System
Length Tip
Diameter 4-20 mA Range*
5 5 meters
99 meters
0 5&8 mm
3 3 mils, pk-pk
4 4 mils, pk-pk
5 5 mils, pk-pk
10 10 mils, pk-pk
15 15 mils, pk-pk
20 20 mils, pk-pk
or
TXA 72
-
Probe Series
-
System
Length Tip
Diameter 4-20 mA Range*
5 5 meters
99 meters
0 5&8 mm
3 11 mm
020 to 80 mils
120 to 160 mils
or
TXR 39
-
Probe Series
-
System
Length Tip
Diameter 4-20 mA Range*
5 5 meters
77 meters
0 5 mm
For Series 3309 NSv or Replacement for RAM Series
TXA 39
-
Probe Series
-
System
Length Tip
Diameter 4-20 mA Range*
5 5 meters
77 meters 0 5 mm 020 to 80 mils
or or
For Series 3000
TXR 30
-
Probe Series
-
System
Length Tip
Diameter 4-20 mA Range*
1 15 ft.
2 20 ft.
1 0.190”
2 0.300”
TXA 30
-
Probe Series
-
System
Length Tip
Diameter 4-20 mA Range*
1 15 ft.
2 20 ft.
1 0.190”
2 0.300” 020 to 80 mils
or or
1.22
*For negative polarity, please add an “N” after the designated number for the Range.
Example: TXA-729-31N
3 3 mils, pk-pk
4 4 mils, pk-pk
5 5 mils, pk-pk
10 10 mils, pk-pk
15 15 mils, pk-pk
20 20 mils, pk-pk
4-20 mA Range*
3 3 mils, pk-pk
4 4 mils, pk-pk
5 5 mils, pk-pk
10 10 mils, pk-pk
15 15 mils, pk-pk
20 20 mils, pk-pk
3 3 mils, pk-pk
4 4 mils, pk-pk
5 5 mils, pk-pk
10 10 mils, pk-pk
15 15 mils, pk-pk
20 20 mils, pk-pk

www.metrix1.com • [email protected]
Sales & Service Tel: [phone] • Fax: [phone] • REV A
Vibration - Condition Monitoring
and Protection
PROXIMITY PRODUCTS
Proximity Probe Transmitter
Trendsetter Model TXR (Radial) and TXA (Axial)
1.23
Cross-Reference from 5465/5488 to Trendsetter TXR/TXA
*For negative polarity, please add an “N” after the designated number for the Range.
Example: TXA-729-31N

3300 5mm Transducer
Product Datasheet
Bently Nevada* Asset Condition Monitoring
Part Number 172036
Rev. K (05/16)
Page 1 of 16
Description
Transducer System
The 3300 5mm Proximity Transducer System
consists of:
la 3300 5mm probe 1, 2
la 3300 XL extension cable (ref 141194-01)
la 3300 XL Proximitor*Sensor 3, 4, 5 (ref 141194-
01)
When combined with a 3300 XL Proximitor
Sensor and XL extension cable, the system
provides an output voltage that is directly
proportional to the distance between the probe
tip and the observed conductive surface. The
system can measure both static (position) and
dynamic (vibration) data. Its primary use is in
vibration and position measurement
applications on fluid-film bearing machines, as
well as Keyphasor*measurement and speed
measurement applications6.
The system provides an accurate, stable signal
output over a wide temperature range. All 3300
XL Proximity Transducer Systems achieve this
level of performance with complete
interchangeability of probe, extension cable,
and Proximitor sensor, eliminating the need for

individual component matching or bench
calibration.
Proximity Probe
The 3300 5mm probe improves upon previous
designs. A patented TipLoc* molding method
provides a more robust bond between the probe
tip and the probe body. The 3300 5mm system is
orderable with Fluidloc cable options for
preventing oil and other liquids from leaking out of
the machine through the cable’s interior.
Connectors
The 3300 5mm probe and 3300 XL extension cable
have corrosion-resistant, gold-plated brass
ClickLoc* connectors. These connectors require
only finger-tight torque (connectors will "click"),
and the specially engineered locking mechanism
prevents the connectors from loosening. The
connectors require no special tools for installation
or removal.
3300 5mm Probes and XL Extension Cables can be
ordered with connector protectors already
installed, or we can supply the connector
protectors separately for installation in the field
(such as when the cable must be run through
restrictive conduit). We recommend connector
protectors for all installations to provide increased
environmental protection7.
Notes:
1. A 5mm probe uses smaller physical packaging and
provides the same linear range as a 3300 XL 8mm
probe (ref 141194-01). The 5mm probe does not,
however, reduce the sideview clearances or tip-to-
tip spacing requirements as compared to an XL
8mm probe.Use the 5mm probe when physical (not
electrical) constraints preclude the use of an 8mm
probe, such as mounting between thrust bearing
pads or other constrained spaces. When your
application requires narrow sideview probes, use
the 3300 XL NSv* probe and extension cable with
the 3300 XL NSv Proximitor Sensor (refer to
Specifications and Ordering Information p/n
147385-01).
2. XL 8mm probes provide a thicker encapsulation of
the probe coil in the molded PPS plastic probe tip to
produce a more rugged probe. The larger diameter
of the probe body also provides a stronger, more
robust case. We recommend the use of XL 8mm
probes when possible to provide optimal
robustness against physical abuse.
3. A 3300 XL Proximitor Sensor is available and
provides many improvements over the non-XL
version. The XL sensor is electrically and
mechanically interchangeable with the non-XL
version. Although the packaging of the 3300 XL
Proximitor Sensor differs from its predecessor, its
design allows for the use of a 4-hole mounting base
to fit it in the same 4-hole mounting pattern and to
fit within the same mounting space specifications
(when the application observes the minimum
permissible cable bend radius). Consult
Specifications and Ordering Information (p/n
141194-01) or our sales and service professional
for more information.
4. Use of XL components with 3300 5mm Probes will
limit system performance to the specifications for
the non-XL 3300 system.
5. The factory supplies Proximitor Sensors that are
calibrated by default to AISI 4140 steel. Calibration
to other target materials is available upon request.
6. When using this transducer system for tachometer
or over-speed measurements, consult
http://www.GEmeasurement.com for the
application note regarding the use of eddy current
proximity probes for over-speed protection.
7. We provide silicone tape with each 3300 XL
extension cable. Use this tape instead of connector
protectors. We do not recommend silicone tape in
applications which will expose the probe-to-
extension cable connection to turbine oil.
Part Number 172036
Rev. K (05/16)
Page 2 of 16

Specifications
Unless otherwise noted, the following
specifications are for a proximity transducer
system between +18°C and +27°C (+64 °F to +80 °F)
with a -24 Vdc power supply, a 10 kΩload, an AISI
4140 steel target, and a probe gapped at 1.27mm
(50 mils).
Electrical
XL Proximitor Sensor Input
Accepts one noncontacting 33005mm Proximity
Probe and XL Extension Cable.
Power
Requires -17.5 Vdc to -26 Vdc at 12 mA maximum
consumption. Operation at a more positive
voltage than -23.5 Vdc can result in reduced linear
range.
Supply Sensitivity
Less than 2 mV change in output voltage per volt
change in input voltage.
Output resistance
50 Ω
Table 1: Probe DC Resistance
Probe
Length (m)
Resistance from the Center Conductor to the
Outer Conductor (Ω)
0.5 7.45 ±0.50
1.0 7.59 ±0.50
1.5 7.73 ±0.50
2.0 7.88 ±0.50
Probe
Length (m)
Resistance from the Center Conductor to the
Outer Conductor (Ω)
5.0 8.73 ±0.70
9.0 9.87 ±0.90
Table 2: Extension Cable DC Resistance
Length of
Extension
Cable
Resistance from Center
Conductor to Center
Conductor (RCORE) (Ω)
Resistance from Outer
Conductor to Outer
Conductor (RJACKET) (Ω)
3.0 0.66 ±0.10 0.20 ±0.04
3.5 0.77 ±0.12 0.23 ±0.05
4.0 0.88 ±0.13 0.26 ±0.05
4.5 0.99 ±0.15 0.30 ±0.06
7.0 1.54 ±0.23 0.46 ±0.09
7.5 1.65 ±0.25 0.49 ±0.10
8.0 1.76 ±0.26 0.53 ±0.11
8.5 1.87 ±0.28 0.56 ±0.11
Note:
Outer conductor refers to the shielded conductor that is
attached to the connector, not the armor braid.
Extension cable capacitance
69.9 pF/m (21.3 pF/ft) typical.
Field Wiring
Recommend using 3-conductor shielded triad
cable 0.2mm to 1.5mm (16 AWG to 24 AWG). 305
metres (1,000 feet) maximum length between 3300
XL Proximity Transducer and monitor. Consult
Part Number 172036
Rev. K (05/16)
Page 3 of 16

Performance Specification 155687 for signal rolloff
at high frequencies when using longer field wiring
lengths or external safety barriers located some
distance from the monitoring system.
Linear Range
2mm (80 mils). Linear range begins at
approximately 0.25mm (10 mils) from target and is
from 0.25 to 2.3mm (10 to 90 mils).
Recommended Gap Setting
1.27mm (50 mils).
Incremental Scale Factor
7.87 V/mm (200 mV/mil) ±6.5% typical, including
interchangeability error when measured in
increments of 0.25mm (10 mils) over the linear
range.
Deviation from best fit straight line
(DSL)
Less than ±0.038mm (±1.5 mil) typical deviation
from best fit straight line.
Probe Temperature Stability (typical)
Over probe temperature range of -35 °C to +177
°C (-31 °F to +350 °F), the incremental scale factor
remains within ±10% of 7.87 V/mm (200 mV/mil)
and the deviation from the best fit straight line
remains within ±0.076mm (±3 mils).
Frequency Response
0 to 10 kHz: +0, -3 dB, with up to 305 metres (1000
feet) of field wiring.
Minimum Target Size
15.2mm (0.6 in) diameter (flat target).
Shaft Diameter
Minimum
50.8mm (2 in)
Recommended minimum
76.2mm (3 in)
When gapped at the center of the linear range,
the interaction between 2 separate transducer
systems (cross-talk) will be less than 50 mV on
shaft diameters of at least 50mm (2 in) or greater.
Care should be taken to maintain minimum
separation of transducer tips, generally at least
40mm (1.6 in) for axial position measurements or
38mm (1.5 in) for radial vibration measurements to
limit cross-talk to 50 mV or less. Radial vibration or
position measurements on shaft diameters
smaller than 76.2mm (3in) will generally result in a
change in scale factor. Consult Performance
Specification 155687 for additional information.
Effects of 60 Hz Magnetic Fields Up to
300 Gauss
Refer to table 3.
Table 3: Output Voltage in Mil (pk-pk)/Gauss (5-
metre System)
Gap XL Proximitor Sensor Probe XL Ext. Cable
10 mil 0.0119 0.0004 0.0004
50 mil 0.0131 0.0014 0.0014
90 mil 0.0133 0.0045 0.0045
Part Number 172036
Rev. K (05/16)
Page 4 of 16

Electrical Certification
Complies with the European CE mark.
Hazardous Area Approvals
Note:
Multiple approvals for hazardous areas certified by
Canadian Standards Association (C/US) in North America
and by Baseefa for Europe and IEC Ex.
Table 4: Field Wiring Limitations
Type Approval Gas
Group
Capacitance
(µF)
Inductance
(mH)*
L/R
Ratio
(μH/Ω)
ATEX and IEC
Zone 0/1 IIC 0.078 0.99 29.2
IIB 0.645 7.41 117.0
IIA 2.144 15.6 234.0
CSA Div 1 A and B 0.070 1.0 29.2
C 0.600 5.0 117.0
D 2.09 11.0 234.0
CSA Div 2 All 0.460 100.0 N/A
North American
3300 XL
Proximitor
Sensor
and
probe, ia:
Ex ia IIC T4/T5; Class I Zone 0 or Class 1 Division 1;
Groups A, B, C, and D, when installed with
intrinsically safe zener barriers per drawing 141092
or when installed with galvanic isolators.
Certificate number 1109248(LR 26744-222)
3300 XL
Proximitor
Sensor
and
probe, nA:
Ex nA IIC T4/T5 Class I Zone 2 or Class I, Division 2,
Groups A, B, C, and D when installed without
barriers per drawing 140979.
T5@ Ta= -35 °C to +85 °C.
T4 @ Ta= -51 °C to +100 °C.
Certificate number 1109248(LR 26744-222)
Europe
3300 XL
Proximitor
Sensor, ia:
II 1 G EEx ia IIC T4/T5. EC certificate number
BAS99ATEX1101, when installed per drawing
141092.
3300 XL
Proximitor
Sensor, nA:
II 3 G Ex nA II T4/T5. EC certificate number
Baseefa 07ATEX0189X, when installed per drawing
140979.
T5 @ Ta= -35 °C to +85 °C
T4 @ Ta= -51 °C to +100 °C.
3300 XL
8mm
probe, ia:
II 1 G EEx ia IIC, Temperature Classification per
table 4-5, EC certificate number BAS99ATEX1099
when installed per drawing 142491.
3300 XL
8mm
probe, nA:
II 3 G EEx nA II, Temperature Classification per
table 4-5, EC certificate number BAS99ATEX3098
when installed per drawing 142491.
Part Number 172036
Rev. K (05/16)
Page 5 of 16

IEC Ex
3300 XL Proximitor Sensor, ia
IECEx BAS04.0055X
Ex ia IIC T4 (-51°C ≤ Ta ≤ +100°C)
/ T5 (-35ºC ≤ Ta ≤ +85ºC)
Terminal Block Connections
Ui= -28VCi = 0
Ii= 140mALi =10µH
Pi= 0.84W
3300 XL Proximitor Sensor, nA:
IECEx BAS04.0057X
Ex nA II T4 (-51°C ≤ Ta ≤ +100°C)
/ T5 (-35°C ≤ Ta ≤ +85°C)
Ui = -28V
3300 XL 8mm and 3300 5mm
Eddy Current Probes, ia:
IECEx BAS04.0056
Ex ia IIC Temperature
Classification per table 5.
Ui = -28V Ci = 1.5 nF
Li = 140 mALi = 200 µH
Pi – 0.84 W
3300 XL 8mm and 3300 5mm
Eddy Current Probes, nA
IECEx BAS04.0058X
Ex nA II for Zone 2 Temperature
Classification per table 5.
Table 5: Probe Ex ia and Ex nA Temperature
Classification
Temperature
Classification
Ambient Temperature (Probe
Only)
T1 -51ºC to +232ºC
T2 -51ºC to +177ºC
T3 -51ºC to +120ºC
T4 -51ºC to +80ºC
T5 -51ºC to +40ºC
Hazardous Area Conditions of Safe
Use:
ATEX
Follow the conditions of safe use included on the
Declaration of Conformance sent with each
product.
Canadian Standards Association (CSA)
Division 1 (Intrinsically safe): Install per Bently
Nevada drawing 141092.
Division 2 (non-Incendive): Install per Bently
Nevada drawing 140979.
IECEx
Zone 0 (Intrinsically safe): The Proximitor® Sensor
must be installed to minimize the risk of impact or
friction with other metallic surfaces.
Zone 2 (non-Incendive): The probe must be
supplied from a voltage-limited source.
Compliance and Certifications
EMC
European Community Directives EMC Directive 2004/108/EC
Standards
EN61000-6-2
EN61000-6-4
American Bureau of Shipping (ABS) Type
Approval
Certification Number 09-HS446965B-PDA
Part Number 172036
Rev. K (05/16)
Page 6 of 16

Mechanical
Probe Tip
Material Polyphenylene sulfide (PPS)
Probe Case
Material AISI 303 or 304 stainless steel (SST)
Probe Cable
75Ω triaxial, fluoroethylene propylene (FEP)
insulated probe cable in the following
lengths: 0.5, 1, 2, 5, or 9 metres (1.6, 3.3, 16.4, or
29.5 feet)
System Length 5 or 9 metres (16.4 or 29.5 feet) including
extension cable
Extension Cable
Material
75 Ωtriaxial, fluoroethylene propylene (FEP)
insulated
Probe and
Extension Cable
Armor
Flexible AISI 302 or 304 SST with FEP outer
jacket
5mm Probe
Tensile Strength
222 N (50 lbf) probe case to probe lead. 222 N
(50 lbf) probe lead to extension cable
connectors
Connector
material
Gold-plated brass or gold-plated beryllium
copper
Recommended case hole and tap size for 1/4-28 case
Drill Size 0.213in
Hole Size 0.218 to 0.222in
Hole Depth 0.376 to 0.750in
Tap Size #3
Recommended case hole and tap size for M8x1 case
Drill Size 7.5mm
Hole Size 7.625 to 7.72mm
Hole Depth 12 to 24mm
Tap Size M8x1
Probe case
torque
5.1 N·m (45in·lb) recommended
7.3 N·m (65 in·lb) maximum
Connector-to-
connector
torque
Refer to the following table: Recommended
Torque
Table 6: Recommended Torque
Connector Type Tightening
Instructions
2 3300 XL gold "click" type connectors Finger tight
1 non-XL stainless steel connector
and 1 3300 XL connector
Finger tight plus 1/8
turn using pliers
Maximum torque 0.565 N•m (0.42 ft•lbf)
Minimum Cable Bend Radius 25.4mm (1.0in)
Weight
Total System 0.71kg (1.6 lb), typical
3300 5mm Probe 323 g (11.39 oz).
XL Extension Cable
34 g/m (0.4 oz/ft)
103 g/m (1.5 oz/ft) (armored)
XL Proximitor Sensor 246g (8.7oz)
Environmental Limits
Probe Temperature Range
-35°C to +177°C (-31°F to +351°F)
Note:
Exposing the probe to temperatures below –34°C (-30°F)
may cause premature failure of the pressure seal.
Extension Cable Temperature Range
-51°C to +177°C (-60°F to +351°F) for standard
extension cable. ref 141194-01
Probe Pressure
3300 5mm probes are designed to seal differential
pressure between the probe tip and case. The
probe sealing material consists of a fluorocarbon
O-ring. We do not pressure test probes prior to
Part Number 172036
Rev. K (05/16)
Page 7 of 16

shipment. Contact our custom design
department if a test of the pressure seal for your
application is required.
Note:
It is the responsibility of the customer or user to ensure
that all liquids and gases are contained and safely
controlled should a proximity probe leak. In addition,
solutions with high or low pH values may erode the tip
assembly of the probe causing media to leak into
surrounding areas. Bently Nevada, Inc. will not be held
responsible for any damages resulting from leaking 3300
5 mm proximity probes. In addition, Bently Nevda, Inc.
will not replace 3300 5mm proximity probes under the
service plan due to probe leakage.
Patents
One or more components or procedures
described in the following patents apply to this
product: 5,016,343; 5,126,664; 5,351,388; and
5,685,884.
Part Number 172036
Rev. K (05/16)
Page 8 of 16

Ordering Information
For a detailed listing of country and product
specific approvals, refer to the Approvals Quick
Reference Guide (document 108M1756) located at
the following website: www.GEmeasurement.com.
3300 5mm Proximity Probes
330171 3300 5mm Probe, 1/4-28 UNF
thread, without armor
330172 3300 5mm Probe, 1/4-28 UNF
thread, with armor
Part Number-AXX-BXX-CXX-DXX-EXX
A: Unthreaded Length Option
Note: Unthreaded length must be at least
0.8in. less than the case length.
Order in increments of 0.1in
Length configurations:
Maximum unthreaded length:
88= 8.8in
Minimum unthreaded length:
00= 0.0in
Example: 0 4 = 0.4in
B: Overall Case Length Option
Order in increments of 0.1in
Threaded Length configurations:
Maximum case length:
96= 9.6in
Minimum case length:
08= 0.8in
Example: 2 4 = 2.4in
C: Total Length Option
05 0.5 metre (1.6 feet)
10 1.0 metre (3.3 feet)
20 2.0 metres (6.6 feet)
50 5.0 metres (16.4 feet)1
90 9.0 metres (29.5 feet)
D: Connector Option
01 Miniature coaxial ClickLoc connector with
connector protector, standard cable
02 Miniature coaxial ClickLoc connector,
standard cable
11 Miniature coaxial ClickLoc connector with
connector protector, FluidLoc cable
12 Miniature coaxial ClickLoc connector,
FluidLoc cable
E: Agency Approval Option
00 Not required
05 Multiple Approvals
Part Number 172036
Rev. K (05/16)
Page 9 of 16

3300 5mm Proximity Probes, Metric
330173 3300 5mm Probe, M8 x 1 thread,
without armor
330174 3300 5mm Probe, M8 x 1 thread,
with armor
Part Number-AXX-BXX-CXX-DXX-EXX
A: Unthreaded Length Option
Note: Unthreaded length must be at least
20mm less than the case length.
Order in increments of 10mm
Length configurations:
Maximum unthreaded length:
23= 230mm
Minimum unthreaded length:
00= 0.0mm
Example: 0 6 = 60mm
B: Overall Case Length Option
Order in increments of 10mm
Metric thread configurations:
Maximum case length:
25= 250mm
Minimum case length:
02= 20mm
Example: 0 6 = 60mm
C: Total Length Option
05 0.5 metre (1.6 feet)
10 1.0 metre (3.3 feet)
20 2.0 metres (6.6 feet)
50 5.0 metres (16.4 feet)1
90 9.0 metres (29.5 feet)
D: Connector Option
01 Miniature coaxial ClickLoc connector with
connector protector, standard cable
02 Miniature coaxial ClickLoc connector,
standard cable
11 Miniature coaxial ClickLoc connector with
connector protector, FluidLoc cable
12 Miniature coaxial ClickLoc connector,
FluidLoc cable
E: Agency Approval Option
00 Not required
05 Multiple Approvals
Probe Accessories
Aluminum probe mounting bracket
The aluminum probe threaded mounting bracket
is the standard mounting bracket for most 3300 5
mm probe installations. The -02 option is supplied
with 2 10-24 UNC-2A mounting screws. The -03
option is supplied with 2 M5 x 0.8-6g mounting
screws. The mounting screws have pre-drilled
holes for safety wire.
137492 -AXX
A: Thread size
02 1/4-28
03 M8 x 1
Phenolic Probe Mounting Bracket
The phenolic mounting bracket is recommended if
additional electric isolation from the mounting
location is required (as in some generator and
electrical motor bearing locations). The -02 option
is supplied with 2 10-24 UNC-2A mounting screws.
The -03 option is supplied with 2 M5 x 0.8-6g
mounting screws. The mounting screws have
pre-drilled holes for safety wire.
Part Number 172036
Rev. K (05/16)
Page 10 of 16

27474 -AXX
A: Thread size
02 1/4-28
03 M8 x 1
75Ω ClickLoc Connector Kit
330153-AA
75Ω ClickLoc Connector Kit for 3300 series probes
and extension cables. Each kit contains 1 color-
coded sleeve per connector.
A: Kit Type
02 1 ClickLoc male connector for 3300 XL
5mm and 8mm extension cable.
03 1 ClickLoc female connector for 3300 XL
5mm and 8mm extension cable.
04 1 ClickLoc male connector for 3300 5mm
probe.
Accessories
02120015
Bulk field wire
1.0mm2(18 AWG), 3-conductor, twisted, shielded
cable for connections between Proximitor Sensor
and monitor.
03200006
Silicone self-fusing tape
9.1-metre (10-yard) roll of silicone tape to protect
connectors. It is easy to install and provides
excellent electrical isolation and protection from the
environment. It is not recommended for use inside
the casing of the machine.
40113-03
Connector Protector Kit
Connector Protector Kit for 3300 5mm probes,
including connector protectors and installation
tools.
136536-
01
Connector Protector Adapter
Makes connector protector kits purchased prior to
1998 compatible with ClickLoc extension cable
connectors.
40180-03
Connector Protectors
Package containing 10 pairs of 75Ω Coaxial
Connector Protectors.
03839410
75Ω Triaxial/95 ohm Coaxial Male Connector
Protector
Placed onto the extension cable; attaches to the
female connector protector on the 5 mm probe to
provide environmental protection of connectors.
03800001
75Ω Coaxial Female Connector Protector
Placed onto 3300 5mm probe leads; attaches to the
male connector protector on the extension cable to
provide environmental protection of connectors.
163356
Connector Crimp Tool Kit
Includes 1 set of multi-connector inserts and
connector installation instructions. Compatible only
with 330153 connector kits or with probes shipped in
2003 or later with ClickLoc connectors uninstalled.
Supplied with carrying case.
Part Number 172036
Rev. K (05/16)
Page 11 of 16

Graphs
Figure 1: Typical 3300 5mm probe and 1 metre of cable at high and low temperatures (XL
Proximitor Sensor and XL extension cable are at 25°C)
Part Number: 172036
Rev. K (05/16)
Page 12 of 16