Nikon CoolPix P7000 User manual

COOLP DIGITAL CAMERA
/_ P7000
User's Manual

2Choose the interval between each shot and
press the _) button.
• The maximum amount of frames that can be taken
during interval timer shooting differs according to the
interval taken between each shot.
- :30 s: 600 images
- 1 rain: 300 images
- 5 rain:60 images
- 10 rain: 30 images
3Pressthe MENU button.
• The camera returns to shooting mode.
4Press the shutter-release button all the way _
down to shoot the first picture and start _
interval timer shooting.
• The monitor isturned offand the power-on lamp blinks
between shots. _:_ _;_,_
The monitor reactivates automatically immediately _ :I_ J
before the next picture is shot.
5Press the shutter-release button all the way down again to finish
shooting.
• Shooting finishes automatically if the internal memory or memory card becomes full,
or when the number of shot frames reaches the upper limit.
o_
o
o
_1_ Notes on Interval Timer Shooting
• To prevent the camera from turning off unexpectedly during shooting, use a fully chargd battery,
• To power the camera continuously for extended periods, usetheACAdapterEH 5a and the Power
Connector EP 5A (available separately) Do not, under any circumstances, use an AC Adapter other
than the EH 5a ora Power Connector other than the EP 5A Failure to observe this precaution could
result in overheating or damage to the camera
• Do not rotate the mode dial to a different setting while performing interval timer shooting
[] More Information
See "File and Folder Names" (_203) for more information 101

o_
g
o
oo
Autofocus Mode
Set to P,S,A orM _ MENU_ P,S, A,M (shootingmenu)(_gl) -_ Autofocusmode
Choose how the camera focuses.
The camera focuses only when the shutter-release button is pressed halfway.
Full-time AF
The camera focuses continuously until the shutter-release button is pressed down
halfway. Use with moving subjects. A sound will be heard while the camera focuses.
[] Note on Autofocus Mode
Thisfeature cannot be used simultaneously with certain features. See"Functions that Cannot be
Applied Simultaneously" (_108) for more information,
Flash Exp. Comp.
SettoP,S,A M->MENU-> P,S,A,M (shootingmenu) (_gl) -_ Flash
or exp. comp.
Flash compensation is used to adjust the flash output by +2.0 EV in increments of
1/3 EV,changing the brightness of the main subject relative to the background.
-0.3 to -2.0
The flash output is reduced from 0.3 to 2.0 EV,in increments of 1/3 EV,to prevent
unwanted highlights or reflections.
0,0 (default setting)
The flash output is not adjusted.
+0.3 t0 +2.0
The flash output is increased from +0.3 to +2.0 EV,in increments of 1/3 EV,to make
the main subject of the frame appear brighter.
At settings other than O.O, the icon for the current setting is displayed on the
monitor (_6).
[] Flash Exp. Comp. in Low Noise Night Mode
Flash exp. comp, can be set even in low noise night mode 1_5%. This setting isstored in the
camera'smemory independently and isnot linked to Flash exp. comp. in shooting modes P,S,A
andM,
102

Noise Reduction Filter
Setto P, S, A or M -_ MENU_ P, S, A, M (shootingmenu)([_]gl )-_ Noisereductionfilter
Set the strength of the noise reduction function that is normally performed when
recording the picture.
• For noise at slow shutter speeds, set with Long exposure NR (_103).
NR Normal (default setting)
Performnoisereduction atthe standardstrength.
NR" Low
Performnoisereduction atalevel lowerthanthe standardstrength.
The setting for the noise reduction filter is shown by an icon displayed on the
monitor during shooting (_6). Nothing isdisplayed for Normal.
Long Exposure NR
Setto P, S, A or M "_ MENU"_ P, S, A, M (shooting menu)([_]gl) -_ Long exposureaR
At slow shutter speeds, pictures may beaffected by"noise" in the form of random ly-
spaced, brightly-colored dots concentrated in dark parts of the image. Reduce
noise at slow shutter speeds. Enabling long exposure NRincreasesthe time needed
to record pictures after they are shot.
AUTOAuto (default setting)
Noisereduction isperformedat slowshutter speedsthat arelikelyto resultin
picturesaffectedby noise.
MR On
Noisereduction isappliedto picturesshotat shutterspeedsof 1/4secondor slower.
Switchingthisto On isrecommendedwhen shooting at slowshutter speeds.
When long exposure NRis performed, the @ icon isdisplayed on the monitor
during shooting (_6).
o_
o
oo
[] Noteon Long Exposure NR
This feature cannot be used simultaneously with certain features. See "Functions that Cannot be
Applied Simultaneously" (_108) for more information, 103

o_
o
oo
Distortion Control
Setto P,S, A or M -_ MENU"_ P, S, A, M (shooting menu) ([_]91) -_ Distortion control
Choose whether to correct the peripheral distortion that occurs due to the intrinsic
characteristics of lenses. Enabling distortion control reduces the size of the frame,
as compared to when distortion control is not enabled.
On
Distortioniscorrected.
0FF off (default setting)
Nodistortion correctionisperformed.
When distortion control isenabled, the current setting isdisplayed during shooting
(_6). Wt_en Off is selected, an icon for tt_ecurrent setting is not displayed.
[] Note on Distortion Control
This feature cannot be used simultaneously with certain features. See "Functions that Cannot be
Applied Simultaneously" (_108) for more information,
104
Wide-angle Converter
Set to P,S, A or M "_ MENU-> P, S, A, M (shootingmenu)([_91) '_' Wide-angleconverter
Set when the Wide-angle (}onverter WOE75A (0.75x) (available separately from
Nikon) is mounted.
The Adapter Ring UR-E22(available separately from Nikon) is also required for
mounting.
On
Setwhen usingthe Wide-angleConverterWC-E75A.Theangle ofview whenthe
WC-E75Aismounted isequivalentto about 21 mm in 35mm [135]format (when
Distortion control is set to Off). The zoom lens is fixed to the wide-angle end.
Thedigital zoom isnotavailable.
OFF None (default setting)
Usewhen noconverterlensisattached(besureto removethe lensadapterringand
attachthe lensring).
The setting for the wide-angle converter is shown by an icon displayed on the
monitor during shooting (_6). Nothing isdisplayed when the setting isNone.

_1_ Notes on the Wide-angle Converter for Shooting
•Set Wide-angle converter to On before shooting. Set Wide-angle converter to None when no
converter lens is attached.
•The built in flash is changed to _ (Off) when Wide-angle converter is set to On. Use flash units
(_202) (available separately from Nikon) to shoot with the flash.
• Using the flash units (available separately from Nikon) may darken the peripheral area of the
picture. Check the picture using the monitor after shooting. A wide panel is recommended when
shooting with the Speedlight SB 600 or SB 900.
• AF Assist illuminator cannot be used when Wide-angle converter is set to On.
• This feature cannot be used simultaneously with certain features. See "Functions that Cannot be
Applied Simultaneously" (_108) for more information.
[] Installing and Removing the Lens Ring
• Beforeattachingthewide angleconverter,
remove the lens ring. Before installing or
removing the lens ring, be sure to turn off
the camera. While pressing the lens ring
release button, rotate the lens ring
clockwise and remove it.
• To attach the lens ring to the camera, align
the lens ring mounting index (white dot) Lens ring release button
with the lens ring release button, and then
rotate the lens ring counterclockwise.
• When not using the wide angle converter, be sure to attach the lens ring onto the camera.
• For more information on attaching the wide angle converter, see the user's manual provided with
the wide angle converter.
Flash Control
Set to P,S,A orM -> MENU_P,S, A,M (shootingmenu)(_gl) @ Flash control
You can set the built-in flash to offeven when you are not using a Speedlight
(external flash unit) (_202) mounted on the camera's accessory shoe.
AUT0 Rut0 (default setting)
When a flash unit is mounted, the flash unit fires. When a flash unit is not used, the
built-in flash fires.
OFF Built-in off
The built-in flash is disabled.
_o
_1_ Note on Flash Control
This feature cannot be used simultaneously with certain features. See "Functions that Cannot be
Applied Simultaneously" (_108) for more information. 105

Active D-Lighting
o
Set to P,S, Aor M"_ MENU_ P,S,A, M (shootingmenu)(_91) -_ Active D-Lighti
ng
"Active D-Lighting" preserves details in highlights and shadows, creating
photographs with natural contrast. The image taken reproduces the contrast effect
that is seen with the naked eye.This is particularly effective for shooting scenes with
high contrast, such as brightly lit outdoor scenery from a dark room or shaded
subjects at a sunny seaside.
_r_ High, _r_ Normal, _t_ Low
Set the level of the Active D-Lighting effect that is applied during shooting.
OFF off (default setting)
Active D-Lighting is not applied.
When Active D-Lighting isenabled, the current setting isdisplayed during shooting
(_6). When Off is selected, an icon for the current setting is not displayed.
_1_ Active D-Lighting
• Additional time is required to record images when shooting using Active D Lighting
• The exposure is reduced in comparison to shooting with Active D Lighting set to Off To ensure
that the gradation is appropriate, adjustments of the highlighted areas, shadow areas and mid
tones are made before recording
• This feature cannot be used simultaneously with certain features See "Functions that Cannot be
Applied Simultaneously" (_108) for more inBrmation
_1_ Active D-Lighting Versus D-Lighting
The Active D-lighting option in the shooting menu adjusts exposure before shooting to optimize
the dynamic range The D-Lighting (_ 136) option in the playback menu optimizes dynamic range
106 in images after shooting

Zoom Memory
Set to P,S,A orM -_ MENU-_ P,S, A,M (shootingmenu)(_gl) _' Zoommemory
When the zoom control isoperated while pressing the Fn button, the camera
changes in steps to the focal length (equivalent to 35mm [135] format of angle of
view) of the zoom lens that is set in advance in Zoom memory. Tile following
settings are available: 28 mm, 35 mm, 50 mm, 85 mm, 105 mm, 135 mm and
200 mm.
•C]loose tile focal length with tile rotary multi selector, and then press tile _)
button to set the check box to on _' or off.
•Multiple focal lengths can be chosen.
• The default setting is on _for all the check boxes.
• To finish the setting, press the rotary multi selector _.
o_
o
oo
_1_ Notes on Zoom Operation
•Operate the zoom control while pressing the Fn button to change the zoom position to focal
length for which the zoom memory is set to on (_ 11),
The changed focal length is the closest to that before the operation, To change the zoom position
to the next focal length level, release the zoom control and then operate it again.
• Release your finger from the Fn button when using the digital zoom. 107

_o
o
o
108
Functions that Cannot be Applied Simultaneously
Theflashmode,the focusmode,the seif4irner/smiietirner/rernotecontrol, the
quick menu,the st_ootingmenu andfi_especializedmenufor Ul, U2 or U3
cannot be usedwith other functions.
Restricted function
Flash mode
i_i:_iii__: iiiiiiiiiii
iiiiiiiii ii
_i__i__i_i:i_iii_i!i
Self:timer/Smile
timer/Remote
control
Setting Description
Focus mode When _ (Infinity) is selected for shooting, the flash is
(_)40) not available.
•When BSS or Multi-shot 16 is selected for
(_]]99) shooting, the flash is not available.
When Continuous is selected for shooting, the
built in flash is not available (_111).
The built in flash is fixed to _ (Fill flash) when
Continuous flash is selected for shooting. The
Speedlight (external flash unit) cannot be used
(_).
The built in flash is not available.
The flash is not available when On is set for shooting.
When Flash control is set to Built-in off, _> (Auto with
red eye reduction), M_ (Manuab, _r_ (Slow sync) and _-_
(Rear curtain sync) flash modes cannot be selected.
AF area mode When Subject tracking is selected for shooting, the
([_84) Selfitimer/Smile timer/Remote control are not
available.
Continuous dl (infinity) cannot be used when Continuous flash
(_)99) is set for shooting.
Auto bracketing
(I_so)
Wide-angle
converter(_104)
Flash control
(C310s)
Image quality
Image size
Smile timer
(C336)
AF area mode
(1_84)
When shooting with the Smile timer, the mode is
changed to AF (autofocus).
When Subject tracking is selected for shooting,
MF (manual focus) is not available.
When Multi-shot 16 is selected for shooting, Image
quality is fixed to Normal.
Image size is fixed to I_ 3648x2736 when NRW
(RAW) is selected for Image quality,
Image size for a JPEG image can be set when NRW
(RAW) + Fine, NRW (RAW) + Normal or NRW
(RAW) + Basic is selected. However,
3648x2432, t_ 3584x2016 and [_ 2736x2736
cannot be selected.
5H
Image size is fixed to [25 (2560×1920 pixds) when
Multi-shot 16 is selected for shooting.

Restrictedfunction _e_g
!S0 sensitivity Continuous
(C3gg)
White balance°_ Picture Control
:ng2
Wide-angle
converter (_ 104)
AF area mode
Description
When shooting in Multi-shot 16, ISO sensitivity is
set automatically according to the brightness when
shooting mode P, S or A is used. The setting for ISO
sensitivity is fixed at 400 for shooting mode M.
White balance is fixed to Auto when Monochrome
is selected _r shooting,
When On is selected for shooting, Preset manual is
not available,
Focus mode When a setting other than Subject tracking is
(_40) selected and _ (Infinity) is selected as the focus
mode for shooting, the camera focuses at infinity
regardless of the applied AF area mode option,
When set to MF(manual focus), the AF area mode
cannot be set.
When Picture Control is set to Monochrome while
AF area mode is set to Subject tracking, the AF area
mode setting automatically changes to Auto.
When using Active D-Lighting for shooting,
Contrast in Manual adjustment cannot be adjusted.
When AF area mode is set to Center (wide),
Center (normal) or Center (spot) while Metering
is set to Spot AF area, the Metering setting
automatically changes to Matrix.
When AF area mode is set to Subject tracking
while Metering is set to Spot, the Metering
setting automatically changes to Matrix,
Metering is reset to Matrix when Active D-Lighting
is set to any mode other than Off.
Continuous and Auto bracketing are not available
simultaneously,
Auto bracketing is reset to Off when Continuous is
set to any mode other than Single.
The setting for continuous is reset to Single when
Auto bracketing is set to any mode other than Off,
Continuous, BSS, Continuousflash, Multi-shot 16,
Intvl timer shooting or Auto bracketing and the
Self timer/Remote control/Smile timer are not
control ([_38) available simultaneously.
.......................
Picture Control Active D-Lighting
(I_ 106)
Metering AF area mode
([_184)
([_106)
Contin uous_': Continuous
bracketing ([-_gg)/Auto
bracketing
(C3s0)
Smile timer
([_36)/Remote
Image quality BSS, Multi-shot 16 or White balance bracketing
([_]68) cannot be used when Image quality is set to NRW
(RAW), NRW (RAW) + Fine, NRW (RAW) + Normal or
NRW (RAW) + Basic.
o_
o
oo
109

_o
o
o
110
_e strUict%%hu_nc_ion........ S%_ti_g _ _-_ Description t'_
Continuous/Auto Picture Control White balance bracketing cannot be used when
b[acketing ([_]92) Monochrome is selected for shooting
Long exposure When On is selected for Long exposure NR, Multi-
NR (_103) shot 16 is not available,
Distortion control When Distortion control is set to On, Multi-shot 16
!_!04! ...............................................................and Intvl timer shooting are not available.
Wide-angle Continuous flash cannot be used when On is set for
converter (_104) shooting
Long exp0sureN R Continuous
(C::399)
Distortion Control Continuous
(I:Z399)
Active D:Lighting _y
([]_]74)
Date imprint
(I:Z336)
AF area mode
([]_]84)
Blinkwarning Smile timer
(_36)/
Continuous
(_99)/Auto
bracketing (_80)
Tone level
information
([_]82)
When Multi-shot 16 is selected for shooting, the Long
exposure NR is not available
Distortion control cannot be used when Multi-shot 16
or Intvl timer shooting is selected for shooting
When ISO sensitivity is set to 3200 or Hi 1, Active D-
Lighting is not available When 3200 or Hi 1 is selected,
Active D-Lighting is reset to Off,
Image quality Date imprint is not available when Image quality is
(_68) set to NRW (RAW), NRW (RAW) + Fine, NRW (RAW)
.............................................................................................................................+as c.
Continuous When Continuous, BSS or Continuous flash is
([_99) selected for shooting, date imprint is not available,
Auto bracketing Date imprint is not available.
(C3s0)
The virtual horizon is not displayed when shooting
with the smile timer.
The virtual horizon and histogram are not displayed
when shooting with Subject tracking.
i.........................................................................................................................................................................................................................................................................................................................................................................................................................................................
Slink warning does not take effect when using the
Smile timer, Continuous is set to a setting other than
Single, or auto bracketing is set.
Blink warning does not take effect when the tone level
information is displayed automatically.
ital zoom cannot be used when shooting with
the Smile timer.
(I:Z336)
The digital zoom cannot be used when MF(manual
focus) is selected,
The digital zoom cannot be used when shooting with
Subject tracking,

Restricted function Setting Description
_Di°_aTz_m_ °_ Image quality The digital zoom can not be used when Image quality
([_68) is set to NRW (RAW), NRW (RAW) + Fine, NRW
(RAW) + Normal or NRW (RAW) + Basic,
'C'o'n"i'i"n"u"o"u"s...........................................'T'h'e"d"i'g"i't'a'T"z'oo"m"c'a"nnot be used when Mu Iti-sh ot 1
(_gg) is selected for shooting,
S!ow shutter • When the shooting mode is P,S or A,the slowest
Speed ([_ 74) shutter speed is restricted to four seconds when the
ISO sensitivity is High ISO sensitivity auto or
16OO, 1/2 second when the ISO sensitivity is 3200,
and 1/8 second when the ISO sensitivity is Hi 1.
When the shooting mode is M, the slowest shutter
speed is restricted to 15 seconds when the ISO
sensitivity is 800, four seconds when the ISO
sensitivity is 1600, 1/2 second when the ISO
sensitivity is 3200, and 1/8 second when the ISO
sensitivity is Hi 1,
When Continuous, BSS or Continuous flash is
selected for shooting, the slowest shutter speed is
restricted to 1/2 second.
When Multi-shot 16 is selected for shooting, the
slowest shutter speed is restricted to 1/30 second.
Built-in flash, Speedlights (external flash unit)
The operation of the built-in flash and the Speedlight %-400, %-600 and %-900 flash units
(available separately from Nikon) are restricted as shown below, depending on the
Continuous setting that is applied.
Continuous mode _!_ Built-in flash '_ Flash units _
Available Available
Continuous Off Available
BSS Off Not available
Continuous flash Available Not available
Multi-shot 16 Off Not available
Intvl timer shooting Available Available
Auto bracketing Off Available
When a flash unit (available separately from Nikon) is mounted on the camera's accessory
shoe, the built-in flash is automatically set to (_) (Off).
When shooting using Continuous or Auto bracketing with the flash mode set to _ (Auto
with red eye reduction) (_32, 34), only the pre flash element of red eye reduction is
performed.
_1_ More Information
See"Notes on Digital Zoom" (_178) for more information.
o_
o
oo
111

S
o
o
£
112
Lip to three setting combinations that are frequently used for shooting (user
settings) can be saved in Ul, U2 and U3.The saved settings can be immediately
retrieved for shooting simply by rotating the mode dial to U1, U2 or U3. This is
convenient when you want to shoot with these settings, or you only want to
slightly change the settings. Shooting is possible in P(Programmed auto), S
(Shutter-priority auto), A (Aperture@riority auto) and M(Manual). The following
settings can be saved in U1,U2 orU3
Specialized Menu for U1, U2 or U3
Shooting mode
(_6o/
Inida] monitor display
(_ 14/
AF area mode
(_84) 6
Quick Menu
Image qua]Ry
(_68)
White balance
(_76) 7
Focal length (35ram equiv.) 2
Flash mode
(_32)
AF assist
(_177) 3
Photo info
(I_173)3
Focus mode
(1_40) s
Image size ]SO sensitivity
(_70) ([_)74)
Auto bracketing
(_80)
Shooting Menu
Picture Control Metering Continuous
(_92) (_g8) ([[_]gg)
Autofocus mode Flash exp. comp. Noise reduction filter
(_ 102) (_ 102) ([_) 103)
Long exposure NR Distortion control Wide-angle converter
(_ 103) (_ 104) ([_ 104)
Flash control Active D-Lighting Zoom memory
(_ 105) (_106) ([_2_]I07)
1 Choose the standard shooting mode (defauk setting is P), The current flexible program (when set
to P), shutter speed (when set to S or M) or aperture value (when set to A or M) settings are also
saved.
2 Set the zoom position for when the mode dial is set. Choose 28 mm (default setting), 35 ram, 50
mm, 85 mm, 105 mm, 135 mm, 200 mm or Current zoom position,
3 This setdng is not applied to the setup menu settings.
4 Set the information displayed on the monitor when the mode dial is set (default setdng is Show
info),
5 Tile current focus distance is also saved when the focus mode is MF(manual focus),
6 The current focus area position is saved when AF area mode is set to Manual.
7 The preset value for preset manual applies to the P, S, A, M, U 1,U2 and U3 shooting modes,

Save the Settings in U1, U2 or U3
The frequently used settings for shooting can be changed and saved in U1, U2
and U3.
1RotatethemodedialtoU1, UPorU3. ___1
2Change to a frequently used combination of shooting settings.
•Pressthe MENUbutton todisplaythe menu andswitch between tabswith the rotary
multi sdector (_)13).
- U1, U2, U8 tabs:Displaythe specializedmenusfor U1, U2 andU3
- P, S, A, M tabs:Displaythe shooting menus.
• Displaythe quick menu by pressingthe quick menu button (_)10, 67).
• Usethe rotarymulti sdector to sdectand setmenu options (_12).
3After changing the settings, choose Save user
settings in the specialized menu for U1, UP
or U3, and press the _ button.
o
oo
4Choose Yes and press the _]_ button.
• Thecurrent settingsaresaved.
• Rotatethezoom control to T (C_)to show the settings.
_1_ Clock battery
If the internal clock battery (_171) is exhausted, the settings saved in U1,U2 or U3 will be reset.
Writing down any important setting is recommended. 113

o
o
Shooting in U1,U2 or U3 (user setting) Mode
Rotate tile mode dial to U1, U2 or U3 to retrieve tile
settings saved in "Save the Settings in Ul, U2 or U3"
(_113).
•Frame the subject and shoot with these settings, or
change the settings as required.
• The setting combinations that are retrieved when the
mode dial is rotated to U1, U2 or U3 can be changed as many times as you
want in Save user settings.
Resetting Saved Settings
Tile settings that are saved for U1, UP and U3 carl be reset.
IRotate the mode dial to Ul, U2 or U3. _ ___
•Setthe usersetting mode to reset. _ %_ _ 4
2In the specialized menu screen for U 1, U2 or
U3, choose Reset user settings and press the
button.
3Choose Yes and press the _) button.
• Thesavedsettingsarereset.
114
[] Resetting for Ul, U2and U3
The settings that are saved in the user settings are reset as follows:
•Specialized menus for U1,U2 and U3: Shooting mode: PProgrammed auto, Focal length:
28 ram, Photo info: information hidden, Initial monitor display: Show info, Flash mode:
_AU[OAuto, Focus: hE Autofocus, AF area mode: NAuto, AF assist: Auto
• Shooting menu, quick menu: Same as the default setting for each item

In shooting mode, pressthe [] (playback) button to
enter playback mode and play back the images that
have been shot (_30). The following operations can
be performed in full-flame playback mode.
'ii i iii iilii! iiii ii iiii ii:iii! iii iiii :i il
Choose PiCtures /_" 0(_ _i_]
...._ Description __Use
PressA, V, • or • to choose a picture to
display.
Pressand hold A, V, • or • to fast 12
forward pictures.
116,
117
W (I_)
119
Thumbnail display/
Calendar display
(except for !ist by date
mode)
Choose the date of
recording again for
playback (list by date
mode)
Rotate the zoom control towards the
W (_';;_)inthe 16-picture thumbnail display
to change to the calendar displ
Rotatethe zoom control towards the W (_;_) in
full-flame playback mode to return to the list by
date screen.
displayed on the monitor, up to about 10×.
P!aybackzoom T(q) Pressthe _) button to return to the fulF 118
...............................................................frame playback mode.
Switch between IIZ]I 14,
displays 82
Record!p!ay voice 132
memos _)
Play back movies 151
Delete pictures 31
Display menu 123
Choose a picture on a
Specified date
[]
Switch tO shooting _ 30
mode
[] Changing the Orientation (Vertical and Horizontal Positioning) of Pictures
Change using Rotate image 1_ ] 30/in the playback menu after shooting 1_ ] 22/,
Hide or show the shooting information, photo
information and tone level information on the
monitor.
Record or play back voice memos up to
20 seconds in length.
Play back the displayed movies.
"_ Delete the displayed pictures.
MENLI Display the playback menu.
_ (l_l) Switch to list by date mode. 119
Pressthe [] button or shutter-release
button to enter the shooting mode.
o_
o
2-
115

o
Rotate the zoom control to W(_1_) in full-frame
playback mode (_30, 115) to display pictures as
thumbnail images in thumbnail playback mode (except
for list by date mode).
Choose pictures
Increase the number
Of thumbnails
displayed!Calendar
display
The following operations can be performed in
thumbnail playback mode.
To Use Description [_[_]
Rotate the rotary multi selector, or press A, V, 12
_,orl_.
Rotate the command dial. g
Rotate the zoom control towards the W (_)
direction to increase the number of
thumbnails from 4 _ g _16 _ Calendar
display.
W(_i_) In calendar display, the images can be
selected according to date by moving the
cursor (_117).
Rotate towards the T(C_)direction to return to
thumbnail display.
..... _,:,?_,_,C_: Rotate the zoom control towards the T (O0
direction to decrease the number of
Decrease number of thumbnails from 16 _ g _ 4.
picture thumbnails T(C_)
displayed R°tate t°wards T(C_)again during 4
thumbnails display to return to full-frame
playback.
Return to full-frame _) Pressthe _) button. 30,
playback 115
Delete pictures "_ Delete the selected picture. 31
[]
Switch to the _ Pressthe [] button or shutter-release button 30
shooting mode '_ to enter the shooting mode.
116

[] Icons on the Thumbnails
When pictu res with Print set (_123) a nd
Protect (_129) settings are selected, the
icons shown on the right appear,
Movies are displayed as film frames,
Film frames
Protect icon
Print-set icon
Calendar Display
Rotate the zoom control towards W(_;'_) during
playback mode when 16thumbnails are displayed
(_116) to change to calendar display.
Move the cursor and choose images by selecting a date.
Dates for which pictures exist are underlined in yellow.
The following operations can be performed in calendar
display mode.
To
Select dale
Return to full-frame
playback
Return to picture list
dis alay
Use
®
T(q)
Description
Rotate the rotary muEti selector, or press A, V,
",orig.
Rotate the command dial.
Change to full-frame playback for displaying
the first picture for that date.
Rotate the zoom control to T(q).
12
9
30,
i11s
_1_ Notes on Calendar display
• Images taken without the date set are treated as images taken on "January 1,2010."
• MENUand _ buttons are disabled while the Calendar is displayed.
[] List by Date Mode
Only the pictures taken on the same date car/be played back in list by date mode (_119), Tile list
by date options (_ ]21 ) are also available only for the pictures taken on the selected dates. 117

_o
o
n
118
Rotate the zoom control to T (q) in full-frame playback
mode (_30) to zoom in on the current picture,
enlarging and displaying the center of the picture.
• The guide at lowerright showswhich portion isenlarged.
The following operations can be performed while
pictures are zoomed in.
To Use Description
Rotatethezoom control to T(O_).Thezoom
T(O0 increasesuptoabout 10×.Zoomalsoincreases
byrotating thecommand dialto the right.
Rotatethezoomcontrolto W(_;_).Whenthe
magnificationratioreaches1x, thedisplay
W([]) returnstofull-frameplaybackmode.
Zoom alsodecreasesbyrotating the
command dialto the left.
Meve the display _ Pressthe rotarymultiselector A,,V, _1or I1"to
area movethe displayareato other areasofthe 12
)icture.
Returnto full-frame 30,
playback _) Pressthe_) button. 115
_"_'÷_ Pressto savethe visible portion only asa
Crop picture MENU separatefile. 145
Switchto the Pressthe[] button or shutter-releasebutton 30
Shooting mode _' to enterthe shooting mode.
Pictures Taken Using the Face Priority Function
When the zoom control isrotated to T (q)during full-
frame playback mode for pictures taken in Face Priority
(_86), the picture is enlarged with the facethat was
detected during shooting at the center (excluding pictures
that were shot using Continuous (_99) or Auto
bracketing (_80)),
• If more than one face was detected, the picture isenlarged with the face that was
focused on at the center of the monitor. Pressthe rotary multi selector A, V, _, or
I_ to display other facesthat were detected.
• When the zoom control isfurther rotated in the T (°0 or W (_;_) direction, the
zoom ratio changes and becomes a normal playback zoom display.

In list by date mode, pictures taken on the same date can be played back.
• In full-frame playback, zooming of images, editing, and movie playbackcan be
performed in tile same way as in tile normal playback mode. Recording and
playback of voice memos can also be performed.
• When the MENUbutton is pressed and the list by date menu (_121) is displayed,
all pictures shot on a specified date can be selected for deletion at the same time,
or slide show, print set or protection can be performed only for the pictures shot
on a specified date.
Selecting a Date in List by Date Mode
IPress the AE-L/AF-L (I_) button during _[]_
playback.
• The list by date screen is displayed.
2Use the rotary multi selector to select the
desired date. _-
• The camera lists up to 29 dates. If pictures exist for more
than 29 dates, all pictures recorded earlier than the
most recent 29 dates are listed together as Others.
• Forthe detailed operations in the list by date screen, see
"Operations in List by Date Mode" ([_)120).
• Pressthe _) button to display the first picture for that
date in full-frame playback.
• Rotate the zoom control to W (_i_) in full-frame
playback mode or when displaying the shooting
information to return to the list by date screen.
• Pressthe AE-L/AFA button to return to the normal
playback mode.
o_
o
_1_ Notes on List by Date Mode
• Only the most recent 9,000 pictures can be displayed in list by date mode. Ifa date includes the
9,001 st picture, an asterisk d) is displayed next to the number of pictures for that date.
• Pictures shot when the date was not set are handled as "January 1,2010_' 119