Nilfisk-Advance Advance SC901 User manual

Advance Models:
56511710 (48 LPG Hybrid), 56511712 (48 Diesel Hybrid),
56511713 (48 Battery), 56511812 (48 Fuel Cell EcoFlex),
56511814 (48 Petrol Hybrid), 56511819 (48 Fuel Cell)
CS7010
Instructions for use Instructions for Use
Original Instructions
Instrucciones de uso
Mode d’ emploi
4/2017 revised 3/2020 REV E
Form no. 56091206
A-English
B-Español
C-Français

A - 2 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
TABLE OF CONTENTS
Page
Introduction................................................................................... A-3
Parts and Service ........................................................................... A-3
Nameplate ...................................................................................... A-3
Modifications................................................................................... A-3
Delivery........................................................................................... A-3
Guidelines When Operating this Machine ...................................... A-3
Cautions and Warnings .................................................................. A-4
General Safety Instructions ............................................................ A-4
Hopper Safety Bar.......................................................................... A-6
Engaging the Parking Break........................................................... A-7
Lifting the Machine ......................................................................... A-7
Transporting the Machine............................................................... A-7
Towing or Pushing a Disabled Machine.......................................... A-7
Know Your Machine...................................................................... A-8
Control Panel................................................................................ A-10
Information Menu Display............................................................. A-13
Preparing the Machine for Use.................................................. A-16
Pre-Operational Checklist............................................................. A-16
Engine Oil –Petrol, LPG ............................................................... A-17
Engine Oil – Diesel....................................................................... A-17
Engine Break-in Period –Petrol, LPG........................................... A-17
Engine Coolant............................................................................. A-17
Engine Air Filter ............................................................................ A-18
Fuel............................................................................................... A-18
Diesel Engine ............................................................................ A-18
LPG Engine ............................................................................... A-18
Petrol Engine............................................................................. A-18
Battery Installation........................................................................ A-19
Main Broom .................................................................................. A-20
Scrub Brushes.............................................................................. A-20
Filling the Solution Tank................................................................ A-21
Filling the DustGuard™ Tank........................................................ A-21
Page
Operating the Machine............................................................... A-22
Startup Homing Sequence ........................................................... A-22
Starting the Diesel Engine............................................................ A-22
Starting the LPG Engine............................................................... A-22
Engine Fault Code for Diesel and LPG Engines Only.................. A-22
Starting the Petrol Engine............................................................. A-22
Detergent System Preparation and Use (EcoFlex™ only) ........... A-23
Sweeping...................................................................................... A-25
Emptying the Hopper.................................................................... A-25
Scrubbing ..................................................................................... A-27
After Use...................................................................................... A-29
Shutting Down the Diesel Engine................................................. A-29
Shutting Down the LPG Engine.................................................... A-29
Shutting Down the Petrol Engine.................................................. A-29
Check Hydraulic Oil...................................................................... A-29
Maintenance Schedule............................................................... A-30
Lubricating the Machine ............................................................... A-31
Charging the Battery (Battery Models) ......................................... A-32
Charging the Battery Pack (Hybrid Models) ................................. A-33
Main Broom Maintenance............................................................. A-34
Side Broom Maintenance ............................................................. A-36
Squeegee Maintenance................................................................ A-37
Squeegee Adjustment .................................................................. A-37
Hopper Dust Control Filter............................................................ A-38
Side Skirt Maintenance................................................................. A-39
Troubleshooting ......................................................................... A-40
Tripping the Circuit Breakers........................................................ A-40
General Troubleshooting .............................................................. A-41
Fault Code Display ....................................................................... A-43
Fault Code History........................................................................ A-47
Accessories / Options................................................................... A-48
Technical Specifications ............................................................... A-49
Material Composition and Recyclability........................................ A-52
Fuel Cell Model – Operating Instructions ..................................... A-52
WARNING: Breathing diesel engine exhaust exposes you to chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm.
 Always start and operate the engine in a well-ventilated area.
 If in an enclosed area, vent the exhaust to the outside.
 Do not modify or tamper with the exhaust system.
 Do not idle the engine except as necessary.
For more information go to www.P65warnings.ca.gov/diesel
revised 10/2018

4/2017 A - 356091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
INTRODUCTION
This manual will help you get the most from your Advance™Sweeper / Scrubber. Read it thoroughly before operating the machine. References to
“right” and “left” in this manual mean right or left as seen from the driver’s seat.
Note: Bold numbers or letters in parentheses ()indicate an item illustrated on pages A-6 – A-13 unless referred to a specific figure number.
PARTS AND SERVICE
Repairs, when required, should be performed by your Authorized Advance Service Center, who employs factory trained service personnel, and
maintains an inventory of Advance original replacement parts and accessories.
Call the ADVANCE INDUSTRIAL DEALER named below for repairs or service. Please specify the Model and Serial Number when discussing your
machine.
(Dealer, affix service sticker here.)
NAMEPLATE
The Model Number and Serial Number of your machine are shown on the Nameplate.
One Nameplate is located on the wall of the operator’s compartment just below the circuit breaker decal. The second Nameplate is located on the
chassis beneath the recovery tank. This information is needed when ordering repair parts for the machine.
Date of Manufacture “Date Code” is also marked on the Nameplate. For example, Date Code “A17” = January 2017.
Use the space below to note the Model Number and Serial Number of your machine for future reference.
MODEL No. _____________________________________________
SERIAL No. _____________________________________________
Note: Reference the separately supplied engine manufacture’s maintenance and operator manual for more detailed engine specification and
service data.
MODIFICATIONS
Modifications and additions to the cleaning machine which affect capacity and safe operation shall not be performed by the customer or user
without prior written approval from Nilfisk Inc. Unapproved modifications will void the machine warranty and make the customer liable for any
resulting accidents.
DELIVERY
Upon delivery, carefully inspect the machine for damage. If damage is evident, contact the trucking company immediately to file a freight damage
claim.
GUIDELINES WHEN OPERATING THIS MACHINE
Always follow the CAUTION guidelines listed below when operating this machine.
CAUTION!
• Use extreme CAUTION when operating this machine. Be certain that you are thoroughly familiar with all operating instructions
before using this machine. If you have any questions, contact your supervisor or your local Advance Industrial Dealer.
• If the machine malfunctions, do not try to correct the problem unless your supervisor directs you to do so. Have a qualified
company mechanic or an authorized Advance Dealer service person make any necessary corrections to the equipment.
• Use extreme care when working on this machine. Loose clothing, long hair, and jewelry can get caught in moving parts. Turn
the Key Ignition Switch OFF and remove the key before servicing the machine. Apply the parking brake before getting off of the
machine. Use good common sense, practice good safety habits and pay attention to the yellow decals on this machine.
• Drive the machine slowly on inclines. Use the Brake Pedal (38) to control machine speed while descending inclines. DO NOT turn
the machine on an incline; drive straight up or down.
• The maximum rated incline for sweeping and scrubbing is 17.6% (10°). The maximum rated incline during transport is 21% (12°).

A - 4 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
CAUTIONS AND WARNINGS
Advance uses the symbols below to signal potentially dangerous conditions. Always read this information carefully and take the
necessary steps to protect personnel and property.
DANGER!
DANGER is used to warn of immediate hazards that will cause severe personal injury or death.
WARNING!
WARNING is used to call attention to a situation that could cause severe personal injury.
CAUTION!
CAUTION is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property.
Read all instructions before using.
GENERAL SAFETY INSTRUCTIONS
Specific Cautions and Warnings are included to warn you of potential danger of machine damage or bodily harm.
This machine is only suitable for commercial use, for example at manufacturing plants, warehouses, cement block & brick facilities,
parking garages, municipal parks, entertainment and transportation facilities.
DANGER!
•This machine emits exhaust gases (carbon monoxide) that can cause serious injury or death, always provide adequate
ventilation when using machine. (Engine models only.)
WARNING!
•This machine shall be used only by properly trained and authorized persons.
•This machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge.
•While on ramps or inclines, avoid sudden stops. Avoid abrupt sharp turns. Use low speed down ramps.
•To avoid hydraulic oil injection or injury, always wear appropriate clothing and eye protection when working with or near
hydraulic system.
•Keep sparks, flame and smoking materials away from battery. Explosive gases are vented during normal operation.
•Charging the battery produces highly explosive hydrogen gas. Charge battery only in well-ventilated areas away from open
flame. Do not smoke while charging the battery.
•Remove all jewelry when working near electrical components.
•Turn the key switch off (O) and disconnect the batteries before servicing electrical components.
•Never work under a machine without safety blocks or stands to support the machine.
•Do not dispense flammable cleaning agents, operate the machine on or near these agents, or operate in areas where
flammable liquids exist.
•Do not pressure wash operator control panel, fuse panel, contactor panel or engine compartment area.
• Do not inhale exhaust gas fumes. Only use indoors when adequate ventilation is provided, and when a second person has
been instructed to look after you.
• Do not use the machine without a falling object protective structure (FOPS) in areas where it is likely that the operator is hit by
falling objects.
• Machines shall be parked safely.
• The machine shall be inspected by a qualified person regularly, in particular regarding the LPG container and their connections,
as required for safe operation by regional or national regulations.
• Observe the Gross Vehicle Weight, GVW, of the machine when loading, driving, lifting or supporting the machine.

4/2017 A - 556091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
CAUTION!
•This machine is not approved for use on public paths or roads.
•This machine is not suitable for picking up hazardous dust.
•Use care when using scarifier discs and grinding stones. Advance will not be held responsible for any damage to floor surfaces
caused by scarifiers or grinding stones.
NOTE: Use care when using abrasive brushes or concrete polishing tools. Advance will not be held responsible for any damage to floor
surface where such usage is inappropriate.
•When operating this machine, ensure that third parties, particularly children, are not endangered.
•Before performing any service function, carefully read all instructions pertaining to that function.
•Do not leave the machine unattended without first turning the key switch off (O), removing the key and applying the parking
brake.
•Turn the key switch off (O) before changing the brushes, and before opening any access panels.
•Take precautions to prevent hair, jewelry, or loose clothing from becoming caught in moving parts.
•Use caution when moving this machine in below freezing temperature conditions. Any water in the solution or recovery tanks or
in the hose lines could freeze.
•The batteries must be removed from the machine before the machine is scrapped. The disposal of the batteries should be safely
done in accordance with your local environmental regulations.
•Do not use on surfaces having a gradient exceeding that marked on the machine.
•Before use, all doors and hoods should be properly latched.
•If the engine misfires or runs rough, stop engine operation and have machine serviced by a qualified technician. Continued
operation under this condition may result in damage to the engine, catalytic converter or other machine components.
SAVE THESE INSTRUCTIONS

A - 6 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
HOPPER SAFETY BAR
WARNING!
See Figure 1. Make sure the Hopper Safety Bar (23) is engaged whenever attempting to do any maintenance work under or near
the raised hopper. The Hopper Safety Bar (23) holds the hopper in the raised position to allow work to be performed under the
hopper. NEVER rely on the machine’s hydraulic components to safely support the hopper.
A - To Engage Hopper Safety Bar:
1. Press and hold the hopper raise switch to raise the hopper.
2. Pull the hopper safety bar handle (21) toward you to retract the safety bar (23).
3. Press and hold the hopper lower switch to lower the hopper until it contacts the hopper safety bar.
B - To Disengage Hopper Safety Bar:
1. Press and hold the hopper raise switch to raise the hopper slightly so it lifts off of the hopper safety bar.
2. Push the hopper safety bar handle (21) toward the front of the machine to extend the safety bar (23).
3. Press and hold the hopper lower switch to lower the hopper.
FIGURE 1
B
A
A
B
21
23

4/2017 A - 756091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
ENGAGING THE PARKING BRAKE
CAUTION!
When parking on an incline, turn the steering wheel fully in one direction such that if the parking brake were to be accidentally
released or fail the machine would not roll and cause damage or bodily injury, if necessary, block the wheels.
A. To Engage Parking Brake:
1. See Figure 2. Press the Brake Pedal (38) completely.
2. With the brake pedal pressed, rotate your foot to engage the Parking Brake Pedal (38A).
B. To Release Parking Brake:
1. See Figure 2. Press the Brake Pedal (38) to disengage the parking brake pedal.
FIGURE 2
FIGURE 3
Lift Point / Tie Down Point symbol
TOWING OR PUSHING A DISABLED MACHINE
CAUTION!
If the machine must be towed or pushed, make sure the Key Switch is in the Off position and do not move the machine faster than a
normal walking pace (2-3 mph, 3-5 kph) and for short distances only.
38A
38
LIFTING THE MACHINE
CAUTION!
Never work under a machine without safety stands or blocks to support the machine.
• When lifting the machine, do so at designated locations (Do Not lift on the hopper).
• See the Lift Point / Tie Down Point locations (33) shown on page A-9.
• See Figure 3. Lift Point / Tie Down Point symbols.
TRANSPORTING THE MACHINE
CAUTION!
Before transporting the machine on an open truck or trailer, make sure that:
•All access doors are latched securely.
• The machine is tied down securely. See the Lift Point / Tie Down Point locations (33).
•The machine parking brake is set.

A - 8 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
KNOW YOUR MACHINE
As you read this manual, you will occasionally run across a bold number or letter in parentheses - example: (2). These numbers refer to an item
shown on these pages unless otherwise noted. Refer back to these pages whenever necessary to pinpoint the location of an item mentioned in
the text. NOTE: Refer to the service manual for detailed explanations of each item illustrated on the next 5 pages.
1 Steering Wheel
2 Operator’s Seat
3 Recovery Tank Tip-Out Lock
4 Solution Tank Fill
5 Recovery Tank Lid
6 Vacuum Filter Access Lid
7 Recovery Tank Drain Hose
8 Left Skirt Assembly
9 Exhaust Pipe (Engine models)
10 Engine Compartment Access Panel Latch
11 Front Wheel
12 Left Side Broom
13 DustGuard™Spray Nozzles (optional)
14 Headlights
15 Right Side Broom
16 Hopper Cover Latches
17 Dust Control Filter
18 DustGuard™ Tank Fill
19 Battery (battery models)
20 Engine/Battery Compartment Latch
21 Hopper Safety Bar Handle
22 Engine Coolant Reservoir (Engine models)
51 Recovery Tank Debris Basket
52 Vac Motor Inlet Shutoff Floats
54 High-Pressure Wash Filter (optional)
55 DustGuard™ Filter (optional)
56 DustGuard™ Shut-Off Valve (optional)
54
1
23
4
56
7
8
9
10
11
12
14
15
16
18
20
21
13
17
19
22
51
52
56
55

4/2017 A - 956091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
KNOW YOUR MACHINE (CONTINUED)
24 Recovery Tank Lid Latch
25 Recovery Tank Tip-Out Grip
26 Circuit Breaker Panel (see troubleshooting)
27 Control Panel
28 Radiator Cap
29 Air Filter Service Indicator
30 Engine Starting Battery (Engine models)
31 LPG Fuel Tank (LPG models)
32 Battery Pack
33 Jack Point / Tie Down Point Location
34 Lower Cover
35 Right Side Door
36 Broom Access Door
37 Drive (Foot) Pedal, Directional/Speed
38 Brake Pedal/Parking Brake
39 Right Scrub Skirt Assy
40 Edge Guard Retainer Knob
41 Solution Filter
42 Solution Shut-Off Valve
43 Solution Tank Drain Hose
44 Squeegee Removal Knobs
45 Squeegee Assembly
46 Squeegee Tilt Adjustment Handle
47 Detergent Cartridges (EcoFlex™ models only)
48 Engine Air Filter
49 Hydraulic Power Unit
50 Engine Oil Dipstick (Engine models)
53 Steering Wheel Tilt Adjust Lever
57 Rear Squeegee Guard (optional)
24
25
26
27
28 29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44 45
46
33
47
50 48
49
53
57

A - 10 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
CONTROL PANEL
A Key Switch
B Emergency Stop
C LCD Display
D Left Turn Indicator
E Left Turn Signal (Optional Brake Light with Turn Signal Kit)
F Information Switch
G Right Turn Signal (Optional Brake Light with Turn Signal Kit)
H Right Turn Indicator
I Menu (located in LCD Display (C) when Information Switch (F) is pressed)
J Navigation Arrows (up, down, left and right)
K Speed Limiter Switch
L Headlight Switch
M Horn Switch
N High-Pressure Wash Switch (optional)
O Extended Scrub Switch (optional)
P Burst of Power Switch (EcoFlex™ only)
Q Scrub Pressure Increase
R One-Touch™ Scrub Switch
S Scrub Pressure Decrease Switch
T Solution Flow Increase Switch
U Solution Switch
V Solution Flow Decrease Switch
W Vacuum/Wand Switch (optional)
X Detergent Switch
Y One-Touch™ Sweep Switch
Z Broom Height Raise Switch
AA Broom Select Switch
BB Broom Height Lower Switch
CC Side Broom Switch
DD DustGuard™ Spray Switch
EE Filter Shaker Switch
FF Dust Control Fan Switch
GG Main Broom Float Switch
HH Hopper Raise Switch
II Hopper Lower Switch
JJ Hopper Door Open Switch
KK Hopper Door Close Switch
A
JJ
EE
DD
KK
B
BB
CC
U
T
W
V
X
Z
AA
M
S
DE GQ
H
HH
II
Y
GG
P
FF
KLNO
J
F
C
I
R

4/2017 A - 1156091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
CONTROL PANEL (CONTINUED)
C1 Hour Meter (Hour Glass and Drive Hours)
C2 Active Fault Codes
C3 Battery Indicator
C4 Solution Tank Level Indicator
C5 Speed
C6 Detergent Indicator (if so equipped)
C7 Detergent Ratio Indicator
C8 Detergent Indicator Bar Graph
FIRST = Minimum Concentration Detergent Mode
SECOND = Maximum Concentration Detergent Mode
NONE = Off
C9 Solution Flow Indicator
C10 Solution Flow Rate Bar Graph
FIRST = Low
SECOND = Medium
THIRD = High
FOURTH = Extreme
NONE = Off
C11 Scrub Pressure Indicator
C12 Scrub Brush Pressure Bar Graph
FIRST = Regular
SECOND = Heavy
THIRD = Extreme
NONE = Off
C13 Low Fuel Warning
C14 Fuel Tank Level (Diesel and Petrol models)
C15 Wrench (Active Fault Indicator)
C16 Warning Symbol (Critical Fault Indicator)
C11
C12
C9
C6
C10
C15
C7 C5
C8
C16
C14
C13
C4
C1
C3
C2

A - 12 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
CONTROL PANEL (CONTINUED)
C17 Solution Tank Empty Indicator
C18 Extended Scrub Active Indicator
C19 Emergency Stop Activated Indicator
C20 No Presence (Operator) Indicator
C21 Recovery Tank Full Indicator
C22 Parking Brake Indicator
C23 Hopper Raised Indicator
C24 Hopper Temperature Indicator (optional)
C25 Clogged Hopper Filter
C26 Check Engine Indicator
C27 Oil Pressure Indicator
C28 Engine Over-Temperature Indicator
C29 Glow Plug Active Indicator (Diesel models)
C30 Vacuum Mode Indicator
C31 Wand Mode Indicator
C32 Detergent Purge Indicator
C33 Battery Low Voltage Indicator
(Battery models = low battery voltage)
(Engine models = low battery pack voltage)
C34 Burst of Power Indicator (EcoFlex models only)
C35 Main Broom Adjustment Indicator
C36 Side Broom Adjustment Indicator
C37 Battery Interlock Open Indicator
C38 Engine Fault Indicator
C17 C20 C21C18 C19
C25 C26C24C22 C23
C30 C31C29C27 C28
C35 C36 C34C32 C33
C37 C38

4/2017 A - 1356091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
INFORMATION MENU DISPLAY
There are three “User Types” (modes) within the Menu display that allow for different functions. The three “User Types” include:
• Operator
• Supervisor
• Technician
User Type Function To Enter the User Type mode
Operator Hours, Faults, Systems Simply turn on the machine
Supervisor Hours, Faults, Systems
and Options Press and hold the Scrub and Solution buttons then turn the key to the on position
Technician Service Technician only See Service Manual
J
F
K L N O
I
Menu
Hours
Faults
System
iExit Select
JJ
F
K L N O
I
Menu
Hours
Faults
Options
System
iExit Select
J
OPERATOR MODE SUPERVISOR MODE
Pressing the Information Switch (F) will display the menu (I). This allows access to change machine settings and gather machine information. The
four Navigation Arrows shown (J) identify which buttons to press to move through the menu. For example, press (K) to move up, press (L) to move
down, press (N) to move left and press (O) to move right. When finished, press the information switch (F) to exit the menu.
revised 10/2017

A - 14 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
INFORMATION MENU DISPLAY (CONTINUED)
Menu Level Notes
12
Hours The Hours menu displays the current machine hours
On Time Displays key-on (power-on) hours
Drive Time Displays drive time (non-neutral) hours
Scrub Time Displays scrub/brush on hours
Recovery Time Displays recovery/vacuum on hours
Engine Time Displays engine-on hours (engine models only)
Faults The Faults menu displays Active and Historical faults
Active Faults Displays list of active faults with timestamp and description*
Fault History
Displays list of fault history with number of events, timestamp and description
List View - shows list of fault codes, quantity and latest time stamp
Detail View – shows selected fault codes, quantity, description and Latest time stamp
System The System menu displays current system information
Firmware Displays current firmware revision number
Serial Num Displays serial number of the control board from factory
* See Fault Code Display

4/2017 A - 1556091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
INFORMATION MENU DISPLAY (CONTINUED)
Menu Level Notes
12
Options Available in Supervisor mode
Scrub Start Scrub level at start of scrub: Light, Heavy, Extreme, Last*
Scrub Max Maximum scrub level allowed: Light, Heavy, Extreme*
BOP Time (s) Burst of Power (BOP) time duration:
min (60), max (300), step (60), default (60)
Solution
Solution sets the mode for the solution rate:
Fixed = Solution flow stays the same despite machine speed
Proportional* = Solution flow increases or decreases with speed of machine
Solution in Rev Leave solution on in reverse? No* or Yes
Shaker Time (s) Amount of time to run shaker:
min (10), max (40), step (1), default (15)
Broom Up in Rev Raise broom when in reverse? No* or Yes
Max Speed (%) Maximum forward speed allowed (% of maximum available speed)
Lock Speed Limit Lockout scrub speed limit for user? No* or Yes
NOTE: Do not allow basic user to enable/disable scrub speed limit
Headlight
Headlight on/off control:
Manual* = panel switch controlled
Auto = always on
Backup Alarm
Backup alarm is active when:
Off* = disabled
Rev = machine in reverse
Rev/Fwd = machine is moving
Rev/Fwd/Hop = machine is moving or hopper is up
Language
Menu display language:
English*
Italiano
Deutsch
Portuguese
Francais
Espanyol
*Default setting

A - 16 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
PREPARING THE MACHINE FOR USE
Read pages 15 – 20 for preparing the machine for use.
PRE-OPERATIONAL CHECKLIST
NOTE: Refer to pages A-8 – A-12 for the reference numbers and letters called out below.
When Action Required
Before Each Use
►Inspect the machine for damage, oil or coolant leaks.
►Squeeze the rubber dust cup on the Engine Air Filter (48) to release built-up dust.
►Check the Air Filter Service Indicator (29).
►Check the engine coolant level (22).
►Check the engine oil level (50).
►Check the hydraulic fluid level.
►Check the Fuel Gauge (C14) on the diesel and petrol models.
►Check the Fuel Gauge located on the LPG tank (31) for propane model.
►Check the Battery Charge Level (C3) on battery models.
►Make sure the battery charger is not connected to the machine.
►Make sure the recovery tank is empty.
In the Driver’s Seat
►Be sure that you understand the operating controls and their functions.
►Adjust the seat to allow easy reach of all controls.
►Turn the (Ignition) Key Switch (A) to the ON position. Check for proper operation of the Horn (M), Hour Meter
(C1) and Headlights (L). Turn the Key Switch (A) to the OFF position.
►Check the Brake Pedal (38). The pedal should be firm and should not go all the way down. The latch should hold
the pedal when applied.
As Needed
►Report all defects immediately to service personnel.
Plan Your Cleaning in Advance
►Arrange long runs with a minimum of stopping or starting.
►Allow 6 inches (15 cm) of broom path overlap to ensure complete coverage.
►Avoid making sharp turns, bumping into posts or scraping the side of the machine.

4/2017 A - 1756091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
ENGINE OIL – PETROL, LPG
Check the engine oil level when the machine is parked on a level surface and the engine is cool. Change the engine oil after the first 50 hours of
operation and every 200 hours after that. Use any SF or SG rated oil meeting API specifications and suited to seasonal temperatures. Refer to
the Engine Workshop manual for oil capacities and additional engine specifications. Replace the oil filter with every oil change.
OIL TYPE TEMPERATURE RANGE OIL WEIGHT
SF or SG rated oil meeting API
specifications and suited to seasonal
temperatures.
Above 77 °F (25 °C) SAE 30 or SAE 10W-30
32 °F to 77 °F (0 °C to 25 °C) SAE 20 or SAE 10W-30
Below 32 °F (0 °C) SAE 10W or SAE 10W-30
ENGINE OIL –DIESEL
Check the engine oil level when the machine is parked on a level surface and the engine is cool. Change the engine oil after the first 50 hours
of operation and every 200 hours after that. Use CF, CF-4 or CG-4 oil meeting API specifications and suited temperatures (*important reference
the oil/fuel type note below for further diesel oil recommendations). Refer to the Engine Workshop manual for oil capacities and additional
engine specifications. Replace the oil filter with every oil change.
OIL TYPE TEMPERATURE RANGE OIL WEIGHT
CF, CF-4 or CG-4 rated oil meeting API
specifications and suited to seasonal
temperatures.
Above 77 °F (25 °C) SAE 30 or SAE 10W-30
32 °F to 77 °F (0 °C to 25 °C) SAE 20 or SAE 10W-30
Below 32 °F (0 °C) SAE 10W or SAE 10W-30
* Diesel Lubricating Oil Note:
With the emission control now in effect, the CF-4 and CG-4 lubricating oils have been developed for use with a low-sulfur fuel used in on-road
vehicle engines. When an off-road vehicle engine runs on a high-sulfur fuel, it is advisable to employ the CF, CD or CE lubricating oil with a
high total base number. If the CF-4 or CG-4 lubricating oil is used with a high-sulfur fuel, change the lubricating oil at shorter intervals.
• Lubricating oil recommended when a low-sulfur or high-sulfur fuel is employed.
Fuel
Lubricating
Oil class
Low sulfur
(0.5 % ≥)High sulfur Remarks
CF OOTBN ≥10
CF-4 OX
CG-4 OX
O: Recommended X: Not recommended
ENGINE BREAK-IN PERIOD –PETROL, LPG
During initial engine break-in period you may experience a slight smell or small amount of smoke coming from the engine.
ENGINE COOLANT
CAUTION!
Do not remove the radiator cap when the engine is hot.
To check the engine coolant level, unlatch the Engine Compartment Access Panel Latch (10) and remove the side panel, and observe the coolant
level in the Engine Coolant Reservoir (22). If the level is low add automotive type anti-freeze appropriately diluted for the environment. Clean the
radiator exterior by washing with low-pressure water or using compressed air every 30 hours.

A - 18 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
ENGINE AIR FILTER
Check the Air Filter Service Indicator (29) before each use of the machine. Do not service the air filter unless the red flag is visible in the service
indicator.
CAUTION!
When servicing the engine air filter elements, use extreme care to prevent loose dust from entering the engine. Dust can severely
damage the engine.
The engine air filter contains a Primary (outer) and a Safety (inner) filter element. The Primary Element may be cleaned twice before being
replaced. The Safety Element should be replaced every third time that the Primary Filter Element is replaced. Never attempt to clean the Inner
Safety Element.
To clean the Primary Filter Element, unsnap the 2 clips at the end of the air filter and remove the end housing. Pull the primary element out.
Clean the element with compressed air (maximum pressure 100 psi (6.89 bar)) or wash it with water (maximum pressure 40 psi (2.75 bar)). DO
NOT put the element back into the canister until it is completely dry.
FUEL
P1
WARNING!
• ALWAYS STOP THE ENGINE BEFORE FILLING THE
FUEL TANK.
• ALWAYS ROTATE THE FUEL TANK OUTWARD
BEFORE REFUELING.
• DO NOT SMOKE WHILE FILLING THE FUEL TANK.
• FILL THE FUEL TANK IN A WELL-VENTILATED
AREA.
• DO NOT FILL THE FUEL TANK NEAR SPARKS OR
OPEN FLAME.
• USE ONLY THE FUEL SPECIFIED ON THE FUEL
TANK DECAL.
On machines with diesel and petrol engines, a decal near the fuel
tank filler neck shows the proper fuel to use in the machine.
See Figure 4. Pull out quick release Pin (P1) then rotate the fuel
tank. Before removing the cap from the tank, wipe all dust and dirt
from the cap and from the top of the tank to keep the fuel as clean
as possible.
On machines with propane engines, a decal near the tank gives
specific information about the proper type of tank to be used on
the machine.
FIGURE 4
DIESEL ENGINE
Fill the tank with Number 2 Diesel Fuel if the machine will be used in an area where the temperature is 30° Fahrenheit (0° Celsius) or higher.
Use Number 1 Diesel Fuel if the machine will be used in an area where the temperature is below 30° Fahrenheit (0° Celsius).
NOTE: If the diesel machine runs out of fuel completely, the fuel system must be bled before the engine can be re-started. To avoid this situation,
fill the fuel tank when the fuel gauge indicates 1/4 tank.
LPG ENGINE
Mount a standard 33 lb. (14.85 kg) liquid withdrawal propane tank on the machine, connect the fuel hose and open the shutoff valve on the tank.
Wear gloves when connecting or disconnecting the fuel hose. Shut the propane tank service valve OFF when the machine is not in use.
PETROL ENGINE
Fill the tank with unleaded (AKI) 87 octane regular petrol that is the average of the RON + MON indicated on pumps as (R+M)/2.
Note: Reference the separately supplied engine manufacture’s maintenance and operator manuals for more detailed engine specification and
service data.

4/2017 A - 1956091206 - CS7010
ENGLISH - AINSTRUCTIONS FOR USE
AB
AD
AC
BATTERY INSTALLATION
See Figure 5. The battery required for this machine is sold separately. The maximum battery weight for this machine is 1,875 lbs (850 kg); the
minimum battery weight is 1,400 lbs (635kg). For proper battery installation, please consult your Advance Industrial Dealer. DO NOT attempt to
install the battery with an overhead hoist or forklift; it can only be installed with a battery cart. Connect the connector plug (AB) on the battery to
the machine plug behind the steering wheel. Make sure the battery is firmly seated against the brace on the left side of the battery compartment.
Reinstall the battery Stop Plate (AC) on the right side of the compartment and snug up the Bumpers (AD) so the battery cannot slide from side-to-
side.
NOTE: If the Stop Plate (AC) is not in place, machine functions will be disabled and the Battery Interlock Open Indicator (C37) will flash.
WARNING!
Battery weight in excess of 1,875 lbs (850 kg) or below 1,400 lbs (635kg) may cause the premature failure of parts including the
tires, and may result in decreased stability and control, which could cause personal injury or death and/or property damage. Use of a
battery in excess of the weight limit will void the warranty.
IMPORTANT!
Follow instructions packed with the battery and charger before charging the battery. Read the instructions for Charging the Battery in
the Maintenance section of this manual.
FIGURE 5

A - 20 CS7010 - 56091206 4/2017
INSTRUCTIONS FOR USEA - ENGLISH
AF AE
AE
MAIN BROOM
Several different main brooms are available for this machine. Contact your Advance dealer if you need help selecting the best broom for the
surface and litter that you will be sweeping. Note: Reference broom maintenance for installation steps.
SCRUB BRUSHES (DOUBLE SCRUB MODE)
1. Make sure the Key Switch (A) is OFF (O).
2. See Figure 6. Raise the side skirt assemblies for easier access. NOTE: Lift straight up on the middle of the side skirt assembly and
engage the catch (AE) to keep the skirt assembly raised while installing the brushes.
3. Pull Lever (AF) outward to disengage the gas spring. This allows the right scrub brush assembly to be swung towards the rear of the
machine and provide easier access to the middle scrub brush.
4. See Figure 7. To mount the brushes (or pad holders) align the lugs on the brush with the holes on the mounting plate and turn to lock in
place according to rotation directions shown.
arrows represent brush installation rotation direction.
Inside arrows represent brush motor rotation while scrubbing.
FIGURE 7
Down Position
Up Position
FIGURE 6
Outside