Nilfisk-Advance P17-150HD User manual

DESCRIPTION PLAN
SafetyPrecautions 3
Machine Operation 4
Machine Maintenance & Storage 4
Parts List 5---9
MachineOperation (Chinese) 10
WiringDiagram 11
WHEN ORDERING PARTS
* Use the 7,8 or 9 digit part numbers from the “part number”
columns in this parts list.
* Specify the model and serial number of the machine.
* Use the space below to record the model and the serial
Number for future reference.
Model SerialNo.
2

SAFETY PRECAUTIONS
!!! This machine must be grounded!
Grounding provides a path of least resistance
for electrical current. To reduce the risk of
electrical shock should the machine
malfunction, the machine has a special
grounding plug. Don’t remove the ground pin
under any circumstances!
This machine is intended for commercial use.
It is constructed for use in an indoor
environment and is not intended for any other
use. Use only recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:
1] Do not operate machine:
-Unless trained and authorized.
-Unless you have read and understand
operators manual.
-In flammable or explosive areas.
-With a damaged cord or plug.
-If not in proper operating condition.
-In outdoor areas.
-In standing water
-With the use of extension cords.
2] Before operating machine:
-Make sure all safety devices are in
place and operate properly.
3] When using machine:
-Do not run machine over cord.
-Do not pull machine by cord or plug
-Do not pull cord around sharp edges or
corners.
-Do not unplug by pulling on the cord.
-Do not stretch cord.
-Do not handle plug with wet hands.
-Keep cord away from heated surfaces.
-Do not pick up burning or smoking
debris such as cigarettes, matches or
hot ashes.
-Report machine damage of faulty
operation immediately.
4] Before leaving or servicing machine:
-Turn off machine.
-Unplug cord from outlet.
5] When servicing machine:
-Unplug cord from outlet.
-Use manufacturer supplied or approved
replacements parts.
3

Operation of Floor Machine
* Read operators manual thoroughly prior to
operating or servicing this machine.
GENERAL USE
1] Remove any obstructions or other
obstacles in the area which is to be cleaned.
2] Place the handle in the upright position and
tilt machine back until handle rests on the
floor.
lBe sure the machine is not plugged
into an outlet.
3] Attach the pad driver or brush to the machine
by placing the clutch plate over the gearbox
hub and turning the driver / brush 1/4 turn.
4] Place machine back into its upright position.
5] Plug power cord into grounded outlet.
* Never use an extension cord in
conjunction with the standard power cord.
6] The handle height may be adjusted by
lifting up on the handle release lever,
located on the right side of the switch
housing. Pull trigger and lower handle to
desired operating position. Release
trigger to lock the handle into position.
7] To start the machine, press the red safety
button on the top of the upper switch
housing, and then squeeze either of the
operating triggers. [the safety button must
be depressed prior to squeezing the
operating triggers].
8] When the machine is in operation, both
hands should be placed on the switch
housing [upper handle].
9] During operation, to make the machine go
right, gently raise the handle. To make the
machine to left, gently lower the handle.
10] To stop the machine at any time, simply
release the operating trigger [s] and the machine
will stop automatically.
MAINTENANCE
To keep the machine performing well for many
years, please follow the following maintenance
procedures.
*Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1] Unplug machine as soon as you are done
using it.
2] Tilt machine back and remove pad driver or
brush.
*Never store a low speed machine with the
pad driver or brush mounted to the
machine
3] Clean the outside of the machine with a mild
cleaner.
4] Check power cord for any damage. If
damage is detected, replace the cord
immediately.
5] Lubricate wheels with a water resistant
lubricant once a month.
6] Check machine for loose or missing nuts and
bolts, and replace as necessary.
7] If the machine is used in a dusty environment,
you may remove the motor cover and blow
the motor clean with compressed air. This
will ensure proper ventilation, and allow the
motor to run cooler.
STORAGE
1] Unplug machine from power source and wrap
cord on handle.
2] Tilt machine back and remove pad driver or
brush.
3] Store machine in upright position and in a dry
area.
4

5

DIA
NO PART NO NO REQ'D
1GV40229 密封端盖 1
2GV40228 "O"密封圈 2
3GV40227 尼龙垫片 2
4VF40104F 铝套座 1
5VF40125B 调位齿轮 1
6VF13502 防松丝母 M6 1
7VF47052 调位齿杆 1
8GT13013 六角螺母 M4 1
9VF40121 拉杆弹簧 1
10 VF40105 拉杆套 1
11 VF44004 长拉杆 1
VF45117 手柄内电线 1
AS41901 防水内套 1
13 VF50120 电源线保护胶圈 1
14 GT13031 内六角螺钉 M6X35 2
15 VF44002-2 绕线架盖板 1
16 VF44002-1 绕线架 1
17 VF40117 主管 1
18 VF48310 手柄护套 2
19 AS22006N 放水拉把 1
20 AS22005N 左开关拉把 1
21 VV13661 十字槽盘头螺钉M4X12 2
22 VF48309 压线块 1
23 VF45118 电源线 1
24 VF44005 电源线保护套 1
25 GT13009 十字槽半沉头螺钉M5X30 5
26 GT13008 十字槽半沉头螺钉M5X20 2
27 GV40218 开关弹簧片 1
28 GV40209BD 保险键 1
29 AS22012N 手柄后盖 1
30 VF44203 电源开关 1
31 VF14212 十字槽盘头螺钉M3X25 1
32 AS22004N 右开关拉把 1
33 GT13014 防松丝母M4 1
34 GT13017 平垫圈Φ4 1
35 AS22007N 调位拉把 1
36 VF48306 定位销 4
37 AS22010N 手柄前盖 2
38 GV40226N "Nilfisk"标牌 1
39 VF14222 十字盘头镙钉 M5X12 4
40 GV40241 防水胶套 1
41 VF14053 内六角螺钉 M6X25 1
HANDLE GROUP FOR P17-150HD & P20-150HD
SCREW M6X25
SCREW M5X12
SEAL SEAT
12 PLUG PROTECTOR,LARGE FEMALE
PIN
FRONT COVER
LOGO
LEVER,RIGHT,SWITCH
NUT,LOCK,M4
WASHER,PLAIN,M4
LEVELING,ROD
SAFETY BOTTOM
REAR COVER
SWITCH ASSY
SCREW,M3X25
SCREW,M4X12
SCREW,M5X20
SCREW,M5X30
SPRING,SAFETY BLOCK
HOOK,CABLE
COVER,HOOK
TUBE
LEVER,LEFT,SWITCH
LEVER,SOLUTION
HANDLE GRIP
NUT,LOCK,M6
ROD LEVELING
CORD,HANDLE
GROMMET
SCREW M6X35
INSERT
NUT M4
SPRING LEVELING
RETAINER
DESCRIPTION
CLAMP BLOCK
CORD,P0WER SUPPLY
SIRAIN RELIEF CORD
COVER
"O"RING,GEAR SEAT
WASHER,NYLON
SEAT,GEAR
GEAR
6

DIA
NO PART NO NO REQ'D
HANDLE GROUP FOR P17-150HD & P20-150HD
DESCRIPTION
42 VF40140 双头螺栓垫 2
43 VF40136 双头螺栓 2
44 VF40130 水箱 1
45 VF40141 水箱压板 2
46 VF13503 防松丝母 M8 4
47 VF99015 双头螺栓胶盖 4
48 VF40139 双头螺栓胶盖 1
49 VF40132 溶液管 1
50 VF40142 螺母 M14 1
51 VF41020 "O"密封圈 1
52 VF40131 阀体 1
53 VF40155 六角元台螺母 M5 1
54 VF40134 锥型密封堵 1
55 VF40138 铜垫圈φ51
56 VF40144 铜螺母 M5 2
57 VF40135 弹簧 1
58 VF40133 放水阀螺堵 1
59 VF40148 拉钩 1
60 VF40137 拉杆 1
61 VF40147 水箱拉杆密封套 1
62 VF40156 链条座 1
63 VF41021 链条 1
64 MF-VF001 水箱组件 1
SPRING
SCREW
LOWER PULLING ROD
UPPER PULLING ROD BRASS
NUT,M5
SEAL,RUBBER
SEAL,TANK
SEAT CHAIN
CHAIN
SOLUTION TANK ASSY
WASHER,PLAIN φ5
SCREW,M5,BRASS
BARN HOSE
NUT,M14
"O"RING
VALVE BODY
CLAMP PLATE
NUT,LOCK M8
RUBBER CAP
HOSE,SOLUTION
BOLT
TANK
GASKET
7

8

DIA
NO PART NO NO REQ'D
1 GT13016 内六角螺钉 M8X60 3
2 VF72202 铝套座支架 1
3 GT13080 内六角螺钉 M6X35 4
4 VF13514 平垫圈 φ83
5 VF13503 防松丝母 M8 3
6 GT13030 平垫圈 φ64
7 VF13502 防松丝母 M6 4
8 VF44013 轮轴 1
9 VF13520 开口挡圈 φ12 2
10 VF50119 鞍型垫圈 2
11 GV40235 轮轴固定块 2
12 VV13621 十字盘头平尾自攻丝 ST5X20 4
13 VA13474 十字盘头螺钉 M5X16 5
14 VF13474A 平垫圈 φ52
15 VF13524 平垫圈 φ84
16 VF13519 弹簧垫圈 φ84
17 GT13018 外六角螺钉 M8X30 4
MF-VF021 16"针座 1
MF-VF022 19"针座 1
19 VF99021 联轴器 1
20 VF999802B 齿轮箱 1
21 MT01102 隔套 1
22 VV13601 弹簧垫圈 φ56
23 VV13636 内六角螺钉 M5X30 6
GV40233 防撞边 17" 1
GV40233A 防撞边 20" 1
25 VF999790 电机 1.5HP 1
26 VF999840 运行电容 20uF/500V 1
27 YLQ14601 小电容罩 1
VF40101N 壳体 17" 1
VF40100N 壳体 20" 1
29 VF40152 机体水管接头 1
30 VF40139 溶液管 1
31 VV20509 十字盘头镙钉 M5X10 4
32 VF44201 5"轮子 2
33 VF40994 头像贴纸 1
34 VF44012 防松螺钉 2
35 VF13666 平垫圈φ62
36 VF13604 齿形垫圈φ54
37 YCQ10615 大电容罩 1
38 AS41902 防水外套 1
39 VF999849 运行电容 100uF/300V 1
40 YLQ17507 螺栓套装 4
41 VF999791 电机连齿轮箱 1
42 VF44003 电机银丝龙贴纸 1
43 VF85206 "NILFISK"贴纸 1
44 VF14222 十字盘头镙钉 M5X12 3
45 VF30001N 电机顶盖 1
46 VF30002 刷盘固定座 1
47 VF47023 电机顶盖密封圈 1
START-UP CAPACITOR(BIG),100uF/300V
BOLT ASSY
MOTOR ASSY 1.75HP
LABEL,MOTOR
BUMPER,TOP COVER
LOGO,NILFISK
TOP COVER,MOTOR
CLUTCH PLATE
SCREW M5X12
PLUG PROTECTOR SAMLL MALE
SCREW,M6X12.7
WASHER,LOCK,OUTER TOOTH
W
ASHER,PLAIN φ6
READ MANUAL LABEL
RUNNING CAPACITOR,20uF/500V
MOUNTING FRAME(SMALL),CAPACITOR
FRAME 17"
BARB HOSE
HOSE,SOLUTION
SCREW M5X10
WHEEL 5"
MOTOR 1.5HP
MOUNTING FRAME(BIG),CAPACITOR
SCREW M5X16
W
ASHER,PLAIN φ5
W
ASHER,PLAIN φ8
W
ASHER,LOCK φ8
SCREW M8X30
16"PAD HOLDER
NUT,LOCK,M6
AXLE
WASHER,LOCK
WASHER,LOCK
CLAMP BLOCK,AXLE
SELF-TAPPING SCREW ST5X20
DESCRIP TION
GEAR BOX
SLEEVE
W
ASHER,LOCK φ5
SCREW M8X60
MOUNTING BASE,GEAR
SCREW M6X35
W
ASHER,PLAIN φ8
NUT,LOCK,M8
W
ASHER,PLAIN φ6
BASE GROUP FOR P17-150HD & P20-150HD
28 FRAME 20"
18 19"PAD HOLDER
24 BUMPER 20"
COULPING
BUMPER 17"
SCREW M5X30
9

安全预防
本机必须接地！
为减少机器因故障而引起的触电危险，本机电
源线插头带有一接地插脚，任何情况下不得去
除该插脚。
本机仅作商业用途，并限于户内使用。务必使
用推荐的附件，操作者应阅读，理解并掌握以
下安全预防措施：
1、以下情况不得操作本机：
z未经培训取得相应资格；
z未仔细阅读和理解操作手册；
z在易燃易爆场所；
z电源线或插头损坏；
z机器存在问题不适合操作；
z在户外时；
z在水中；
z使用延长线；
2、操作机器前：
z务必确保所有安全装置动作正常；
3、使用机器时：
z不得碾压电线；
z不得靠牵拉电线的方式移动机器；
z不得将电线置于物件锋利的边、角；
z不得用拉电线的方式拔取插头；
z切勿用湿手拔取插头；
z始终使电源线远离发热的物件表面；
z应立刻报告机器任何之异常及损坏情
况；
4、离开机器或进行维护前：
z务必关机并拔下电源插头；
5、进行维护时：
z应拔下电源插头；
z使用产商推荐的或认可的配件；
储存时
1、拔下电源插头；
2、取下针座或刷子；
3、直立存放于干燥的场所；
维护与保养
为使本机始终保持良好的性能，请遵循以下程
序保养本机
进行任何维护、保养工作前，必须确保
机器已断开电源
1、机器一经使用完毕，立即拔下电源插头；
2、取下针座或刷子；
存放机器时，切勿忘记取下针座或刷子
3、用中性清洁剂清洁机器；
4、检查机器电源线有无破损，如有应立即进
行更换；
为避免危险，若电源线破损，必须联系
当地售后服务部进行更换；
5、每月用防水润滑剂润滑轮子、轴；
6、检查机器有否遗失螺母、螺栓并进行更换；
7、机器在粉尘的场所使用后，应取下电机顶
盖，用压缩空气吹净附着在电机上的灰尘
以保证良好的通风。
操作说明
使用或维护本机前务必仔细阅读说明书
1、使用前应清理工作区域内的杂物、纸屑等；
2、将手柄置于垂直位置后，将机器倾斜使手
柄靠在地面；
确认机器此时未接通电源；
3、松开螺母，取下中心定位器；
4、取合适的抛光垫粘在针座上，并用中心定
位器压紧；
5、将机器置于垂直位置；
6、将电源线插头插入带接地的插座中；
切勿使用与电源线不一致的延长电缆；
7、拉住调节拉把将机器手柄调节至合适操作
位置；
8、按下位于手柄上方的红色按钮同时拉住
左、右拉把即可启动机器；
9、操作时、双手必须牢牢握住操作手柄；
10、操作时，只要轻轻地抬起手柄，机器便
会向右移动，轻轻按下手柄，机器便会向
左移动；
11、停机时，只需松开左、右拉把即可；
10