Nilfisk-Advance COMBAT User manual

www.nilfisk-advance.com
1
Instructions for use

DOVVXFKDVSODVWHUJLEGXVWDQG
DVEHVWRVRUJDVGRLQJVRPD\
H[SRVHSHRSOHWRVHULRXVKHDOWK
ULVNV
2

'XVW&RPSDUWPHQW&RYHU
+(3$
'XVW&RPSDUWPHQW
&/($1(56.(7&+0$3
'867&203$570(17 68%$66(0%/<6.(7&+0$3
3

PRECAUTIONARY MEASURES
If the opening that sucks in the air, thesuction pipe orthe telescopic wand on pipe
are blocked, you should switch off the vacuum cleaner at once. First clear the
blocked substance before you attempt to start the vacuum cleaneragain.
1. Do not operate the vacuum
cleaner too close to heaters
and like radiators, cigarette
butts etc.
2. Before you insert the plug
into the wall contact, make
sure your hand is dry.
This vacuum cleaner is equipped witha plug and acable,which rewinds automatically.
If anything gets damaged, both the plug and the cable must to be repaired by a
qualified repairman or electarician.
4


%HIRUH\RXVWDUWXVLQJWKHYDFXXP
FOHDQHUSOHDVHUHPRYHODUJHRU
VKDUSREMHFWVIURPWKHIORRULQ
RUGHUWRSUHYHQWWKDWWKH+(3$
ILOWHULVGDPDJHG
:KHQ\RXZDQWWRSXOOWKHSOXJ
IURPWKHZDOOFRQWDFWSOHDVHGR
WKLVDWWKHSOXJLWVHOIDQGQRWE\
PHDQVRIWKHHOHFWULFDOFDEOH

ASSEMBLING VACUUM CLEANER
Always remove the plug from the power socket before fitting or removing
accessories!
1. Connecting vacuum cleaner
1. Fitting or removing the flexible hose
Fitting:
Insert flexible hose into the air intake duct
on the front of appliance. Press until it clicks
into position.
Removing:
Removing the plug from the power socket. To release the
flexible hose firmly from the air intake duct.
2.Fitting the extension tubes and accessories
a. Fitting the telescopic tube to the handle.
b. Fitting the nozzle to the telescopic tube.
QR]]OH
5

c. Fitting Floor nozzle
Ideal for the daily cleaning on carpets and hard floors.
Clean on the carpet
Clean on the hard floor
6
d. Extra nozzles
Hard floor nozzle
Use the nozzle for hard floors.
Turbo nozzle
Use the turbo nozzle for efficient carpet cleaning.

2.Cleaning tools use
The crevice tool and dusting brush are stored on the accessories holder.
1.Crevice tool:
For radiators, crevices, corners, baseboards and between cushions.
2.Dusting brush is used for the furniture,venetian, blinds, lamp
shades and shelves.
7

INSTRUCTIONS FOR USE
Before using appliance, unwind a sufficient length of cable and insert the plug
into the power socket. A yellow mark on the power cable shows the ideal cable
length. Don’t expend the cable beyond the red mark.
1.Press the ON/OFF button to switch the appliance on.
2. To rewind the power cable, press the rewind button with one hand and guide the
cable with the other hand to ensure that it does not whip causing damage.
Yel l o w
Re d
Cabl e Rewi nd But t on
8

MAINTENANCE
1. Spilling rubbish from the dust compartment subassembly
zAlways operate the cleaner with the dust compartment subassembly
installed.
zIf you forget to attach HEPA and filter or attach it in a wrong manner, the
dust compartment subassembly may not rinse.
1. After removing the flexible tube, hold handle
and press the locking button.
2. Carry the dust compartment subassembly.
3. Carry away the dust-glass cap and empty rubbish



1
2
4. Empty rubbish and fix the dust compartment subassembly.
5. Replace the dust compartment subassembly until it is locked.
9
2.Cleaning and changing filter or HEPA
zFilter for air-inlet should be cleaned at least twice a year or when it becomes
visible solid.
zClean HEPA for air-let when you find it is filled in.
zHEPA for air-inlet and filter for air-outlet are changed.
zAlways operate the cleaner with filters and HEPA installed.
Otherwise, reduced suction or motor damage may be result.
zDisconnect from electrical outlet, before cleaning filter.
Do not use a washing machine to rinse filter.
Do not use hair drier to dry it.
Cleaning and changing filter and HEPA for air-inlet
Dry filter in the shade only

(1) After opening the dust compartment subassembly,
rotate HEPA until it is unlocked
(2) Remove HEPA.
(3) Rinse filter and HEPA in lukewarm water and dry Filter and HEPA completely.
(HEPA is rinsed by brush.)
(5) Put the filter into the Grille-Filter and rotate HEPA or change new HEPA, then put

themback.
2.Changing filter for air-outlet
(1) Open the grille for air-outlet.
(2) When open the grille for air-outlet, the filter for air-outlet is found.
(3) Take the filter out and change a clean one.
(4) Close the grille for air-outlet.
10