NINGBO WELL ELECCTRIC APPLIANCE LS-01RD User manual
1/4
MODEL:LS‐01RDNINGBOWELLELECCTRICAPPLIANCECO,.LTD
LED STRING LIGHT INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electrical products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS
Do not use these products outdoors unless marked suitable for indoor and outdoor use. When products are used
in outdoor applications, connect the product to a Ground Fault Circuit Interrupting(GFCI) outlet. If one is not provi-
ded, contact a qualified electrician for proper installation.
Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
Do not let lamps rest on the supply cord or on any wire.
Do not use this product for other than its intended use.
Do not hang objects from cord, wire, or light string.
Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
Do not cover the product with cloth, paper or any material not part of the product when in use. This product is
equipped with push-in type lamps. Do not twist lamps. It is acceptable to omit this item if the product does
not contain push-in type lamps. This product employs overload protection(fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any
additional strings or products that maybe attached to the product. Replace the fuse as per the user servicing
instructions(follow product marking for proper fuse rating) and check the product. If the replacement fuse
blows, a short-circuit may be present and the product should be discarded. It is acceptable to omit this item if
the fuse is not replaceable or where overload protection is not required.
POWER SUPPLY
CAUTION: Risk of electric shock. Avoid making connections or disconnections when the equipment is wet.
Do not use with extension cord near water or where water may accumulate. Do not submerse.
CAUTION - To reduce the risk of fire, electric shock or injury to persons:
1. SUNBEAM Electric String Lights are intended for installation indoor or outdoor.
2. String Lights must be supported by steel guide cables or other suitable supporting hardware such as
s-hooks,screw hooks or zip ties(not included) whenever span distances exceed twenty
four feet. See Installation Methods on page 4.
WARNING: - RISK OF ELECTRIC SHOCK!!
Disconnect power supply at source prior to wiring,replacing light bulbs or servicing in any way.
BULB REPLACEMENT
1.Unscrew fixture nut counter clock-wise
2.Insert new bulb aligning guide on module to groove inside
socket.
3.Screw in fixture nut clock-wise.
Includes two extra bulbs.
Bulbs last up to 25,000 hours.
Additional bulbs available at
WWW.SUNBEAM.COM
2/4
MODEL:LS‐01RDNINGBOWELLELECCTRICAPPLIANCECO,.LTD
REMOTE CONTROL
(See illustration)
1. Turns the lights ON/OFF.
2. Increase/Decrease brightness/speed:Press(▲/▼)to
choose brightness level.(Only work in single color mode )
Press(▲/▼)to decrease or increase the color changing
speed.(Only work in color combination mode)
3. Color：Press to change string light color to Red/Green
/Bule/White.
4. Mode:Press button to select one of the 9 color combination
Modes.(see chart to right)
5. Timer: (1)Press button for the 1st time ,the red lights flashing
3 times,automatic shut down after 2 hours; (2)press button
for the 2nd time,the green light fashing 3 times,automatic
shut down after 4 hours; (3) press button for the 3rd time,the
bule lights fashing 3 times,automatic shut down after 6 hours;
(4)press button for the 4th time,the white light flashing 3 times,
automatic shut down fater 8 hours;
To exit the timer mode, press the ON/OFF key to turn
off the power.
6. Match: After the controller and light string are connected, turn
on the power and the red light flashes quickly into the code
mode. Press Match button within 10 seconds. The red light
stops flashing to indicate the success of the code. The
controller can be code 10 remote controls.
PULLOUT
TABTO
ACTIVATE
BATTERY
MODE BUTTON FUNCTIONS
1. Red to green
2. Red to blue
3. Red to white
4. Green to blue
5. Green to white
6. Blue to white
7. Red to green to blue
8. Red to white to blue
9. Red to green to blue to white
3 Volt,CR2025 battery included
3/4
MODEL:LS‐01RDNINGBOWELLELECCTRICAPPLIANCECO,.LTD
The controller function button controls all color changing
functions except the brightness and the color changing
speed. Press and hold button to turn off. In the event that
the remote control is lost, the controller function button
can be instead of the remote control.
1. Power supply
2. Controller
3. Controller Function BUTTON: Press button to select one
of the 13 color combination modes.(see chart to right)
Press and hold button to turn off.
4. String light connection adapter.
When unit is turned on, it will start at the last mode.
CONTROLLER FUNCTION BUTTON
1. Red
2. Green
3. Blue
4. White
5. Red to green
6. Red to blue
7. Red to white
8. Green to blue
9. Green to white
10.Blue to white
11.Red to green to blue
12.Red to white to blue
13.Red to green to blue to white
Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothe
followingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,
and(2)thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
NOTE:Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor
aClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsare
designedtoprovidereasonableprotectionagainstharmfulinterferenceina
residentialinstallation.Thisequipmentgeneratesusesandcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththe
instructions,maycauseharmfulinterferencetoradiocommunications.
However,thereisnoguaranteethatinterferencewillnotoccurinaparticular
installation.Ifthisequipmentdoescauseharmfulinterferencetoradioor
televisionreception,whichcanbedeterminedbyturningtheequipmentoffand
on,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreof
thefollowingmeasures:
□Reorientorrelocatethereceivingantenna.
□Increasetheseparationbetweentheequipmentandreceiver.
□Connecttheequipmentintoanoutletonacircuitdifferentfromthatto
whichthereceiverisconnected.
□Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Thisproductcontainsabutton
battery.Ifswallowed,itcouldcause
severeinjuryordeathinjust2hours.
Seekmedicalattentionimmediatel
y
.
Cetarticlecontientunepilebouton
ENcasd’inestion,cettepilepourrait
Causerdegravesblessuresoulamort
Endeuxheures.DemandezI’aide
d’unprofessionnellasanté
immédiatement.
Esteproductocontieneunapilade
botón.Encasodeingestión,puede
provocarlesionsgravesolamuerie
entansólo2horas.Busqueatencion
médicadeinmediato.
4/4
MODEL:LS‐01RDNINGBOWELLELECCTRICAPPLIANCECO,.LTD
CONECTING STRING LIGHTS
INSTALLATION METHODS
1. Using a guide wire with S-hooks or zip ties(not included)
2. Attached to a structure
Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Connect to
Power Outle
t
Femalemale
Femaleca
p
TIGHTLY FEMALE END IF NOT CONNECTING
MULTIPLE STRING LIGHTS, OR LAST SET OF
CONNECTED STRING LIGHTS.
Connect to string light
(if connecting two or more)
Attach guide wire to
structural support Attach guide wire to
structural support
Guide wire
(
n
ot
in
c
l
uded)
S-hooks or zip ties
(not included)
STRUCTURAL
SUPPORT
STRUCTURAL
SUPPORT
STRUCTURAL
SUPPORT
Attach to
Structural support
MINIMUM EVERY 24 FEET
Attach to
Structural support
MINIMUM EVERY 24 FEET
LIMITED WARRANTY
This product is warranted to be free from defects in
workmanship andMaterials for up to 2 years from
dateofpurchase.
SAVE THESE INSTRUCTIONS
