HERA LB Series User manual

21
1x(optional)1x(optional)
3x2x
Dimension in mm(inch)
!Read the instruction carefully before installation，non-observance of this instruction may
cause damage to the fixture or hurt to human body. The installation must be carried out by
a qualified electrician in accordance with local or national codes.
Cut off the power supply before installation and maintenance !
Regularly check the light source , the LED power supply, the cord and other accessories.
If any part is damaged, the product should not be used.
Keep this instruction manual handy for future use.
The light source of these product are non-changeable light diodes(LED).
Do not disassemble the product, as the light diode can cause damage to the eyes.
Use only with Class 2 power supply
11° for Installation
1.Fixed the mounting seat.
2.Fixed buckle.
12(1/2”)
LB/AL/10/4000/XX
LB/AL/12/4000/XX
LB/AL/14/4000/XX
LB/AL/18/4000/XX
LB/AL/20/4000/XX
LB/AL/21/4000/XX
LB/AL/25/4000/XX
Tools
Driller
14-15mm
(9/16”)
Ruler Pencil Screwdriver
Drill bit
4x2x
2x 5x
LB/AL/29/4000/XX
LB/AL/33/4000/XX
L18(11/16”) 50(2”)
®
L≤100（L≤
3-15/16”
）
L≤100（L≤
3-15/16”
）
LED Power Supply
Splitter
Series: LB
Attentions:
Instruction Manual
L
Model Rated Input Power ta
Minimum Mounting
Space(LxWxH)
24V 4W
-20~35°C
(-4~95°F)
LB/AL/10/4000/XX
264x100x100mm
(10-3/8”x3-15/16”x3-15/16”)
24V 6W
-20~35°C
(-4~95°F)
LB/AL/12/4000/XX
317x100x100mm
(12-1/2”x3-15/16”x3-15/16”)
24V 6W
-20~35°C
(-4~95°F)
365x100x100mm
(14-3/8”x3-15/16”x3-15/16”)LB/AL/14/4000/XX
24V 8W
-20~35°C
(-4~95°F)
470x100x100mm
(18-1/2”x3-15/16”x3-15/16”)
LB/AL/18/4000/XX
24V 8W
-20~35°C
(-4~95°F)
520x100x100mm
(20-1/2”x3-15/16”x3-15/16”)
LB/AL/20/4000/XX
24V 8W
-20~35°C
(-4~95°F)
LB/AL/21/4000/XX
525x100x100mm
(20-11/16”x3-15/16”x3-15/16”)
24V 10W
-20~35°C
(-4~95°F)
LB/AL/25/4000/XX
661x100x100mm
(26”x3-15/16”x3-15/16”)
24V 12W
-20~35°C
(-4~95°F)
770x100x100mm
(30-5/16”x3-15/16”x3-15/16”)
LB/AL/29/4000/XX
24V 14W
-20~35°C
(-4~95°F)
865x100x100mm
(34-1/16”x3-15/16”x3-15/16”)LB/AL/33/4000/XX
254
(10”)
307
(12-1/16”)
355
(14”)
460
(18-1/8”)
510
(20-1/16”)
515
(20-1/4”)
651
(25-5/8”)
(29-15/16”)
760
855
(33-11/16”)

!
3.
43
1.Fixed the mounting seat.
60° for Installation
2.Fixed buckle.
®
LED Power Supply
Splitter
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11. Do not cut wirin
g
or the li
g
htin
g
s
y
stem ma
y
be dama
g
ed.
12.
a.
b.
Cleaning Instructions: Only clean with a mild cleaning agent using a soft cloth
Safety Instructions
"Caution" To reduce the risk of fire, electric shock, or injury to persons:
The Class 2 power supply is not concealed.
The National Electrical Code (NEC) does not permit cords to be concealed where damage to the
insulation may go unnoticed. To prevent fire danger, do not run cords behind walls, ceilings, soffits, or
cabinets where it may be inaccessible for examination. cords should be visually examined periodically
and immediately replaced when any damage is noted.
For best results, have lighting professionally installed by a qualified Licensed Electrician.
Connect only to Hera LED Driver with constant output voltage 24V DC Max.
Do not exceed the maximum number of light fixtures or damage to the driver may result.
This portable cabinet light is not intended to allow bulb replacement. There are no user serviceable
parts inside light.
Not intended for recessed installation in Ceilings and soffits.
"Not intended for surface installation inside built-in furnishings such as kitchen cabinets, china
cabinets, or trophy cases;
The Line Voltage power supply cord is not concealed or routed through openings in the
cabinet or furnishing.
The portable Cabinet Luminaire may be installed inside a kitcen cabinet or other built-in furnishing
provided that the cabinet or built-in furnishing is provided with a dedicated receptacle and:
Connect only to listed direct plug-in or cord connected Class 2 power supply with a constant output
voltage of 24V DC max. Use of power supply other than provided by Hera is not allowable and will
void warranty.
Use only insulated staples or plastic ties to secure cords
Route and secure cords so that they will not be pinched or damaged when cabinet is pushed to the
wall
L≤100（L≤
3-15/16”
）L≤100（L≤
3-15/16”
）
NOTE:
For other beam angles,the suitable installation should be determined
by a qualified field technician.
®