NiteRider MINEWT PRO 750 User manual

150-22841 - Rev A
MiNewt Pro 750
PROTECTING YOUR INVESTMENT
Properly charge your battery to maximize its lifespan
(see the “Battery Charging And Care” section for detailed
information).
The MiNewt Pro 750 will perform in wet weather
conditions, but submerging it in water will damage the
system.
RUN TIMES
Light Level
High
Med
Low
Walk
Time*
1:30
3:00
6:00
35:00
Lumens
750
500
250
40
The MiNewt Pro 750 will run up to:
*Run times are approximations and will vary.
NiteRider Technical Lighting Systems, Inc.
8295 Aero Place, Suite 200
San Diego, CA 92123
LOW BATTERY INDICATOR
With approximately 15% battery capacity remaining, the
indicator light on the headlamp will turn from blue to red.
BATTERY CHARGING AND CARE
1. Plug the AC Adapter into an electric outlet, then plug
the cable from the AC Adapter into the battery.
2. The indicator light will be red until the battery is fully
charged; then it changes to blue.
3. Unplug the AC Adapter from the battery by grasping
the connectors rather than the cable.
4. Leaving the battery and AC Adapter connected
indenitely will not harm the battery.
5. When storing for an extended period of time, charge
the battery every three months to maximize battery life.
RIDING AT NIGHT
While a MiNewt Pro 750 lighting system will improve
your view, control and enjoyment of night riding,
please remember that cycling at night is an inherently
dangerous activity. In addition to using your lighting
system properly and riding with extreme caution,
NiteRider urges you to:
• Never ride alone.
• Always let someone know where you are going.
• Wear a helmet and reective clothing.
• Carry an auxiliary light and emergency supplies.
• Make sure the headlamp, mounting bracket and
battery are securely fastened.
• Always disconnect the battery from the headlamp
when transporting the light system.
SUPPORT
If you experience diculties during product installation or
operation, NiteRider provides free telephone support on
weekdays from 8:00 AM to 4:30 PM (PST) at
800.466.8366, ext 4. You may also e-mail us at
[e-mail].
WARRANTY
NiteRider stands behind its products with the following
warranties:
• Lifetime warranty on all mechanical components
• 2 years on electrical components
• 180 days on rechargeable batteries
To obtain warranty service, it is preferable to have your
original sales receipt. Contact the NiteRider customer
service department at 800.466.8366, ext. 4 to obtain a
Return Merchandise Authorization (RMA) number. The
RMA number must be prominently displayed on the
outside of yourpackage. The product must be properly
packaged to prevent damage in transit. For complete
warranty information, please visit our website at
www.niterider.com.

PARTS LIST AND IDENTIFICATION
Please verify the contents of your MiNewt Pro 750 system
A. MiNewt Pro 750 Headlamp
B. Li-Ion Battery
C. Handlebar Mount
D. Low Prole Bike Helmet Mount
E. A/C Adapter
F. 36” Extension Cable
A.
B.
C. D.
E. F.
Knob
Hinge
DISCOVER THE NIGHT
Thank you for choosing the MiNewt Pro 750 from NiteRider, the
innovator in technical lighting systems. The MiNewt Pro 750
combines a high-powered white LED headlamp and a Li-Ion
battery.
To get the most from your NiteRider light, we urge you to
familiarize yourself with the following safety and operating
instructions.
MOUNTING THE LI-ION BATTERY
1. Thread the velcro strap through the slots on the bottom of
the battery.
2. Attach the concave surface of the battery to a safe,
convenient location on the handlebars, stem or frame,
placing the velcro strap over the mating surface.
MOUNTING THE HEADLAMP
The MiNewt Pro 750 headlamp can be mounted to the
handlebar or a helmet.
Straight Handlebar Mount
The Straight Handlebar Mount (SHM) is designed to t on
virtually any handlebar.
1. Turn the knob counter-clockwise,
allowing the hinge to swing open.
2. Place the mount on the handlebar
on either side of the stem, orienting
the rectangular notch in the slider clip
to the rear.
3. Swing the hinge down to make contact with the
handlebar.
4. Swing the bolt up, seating the knob into its recess.
5. Turn the knob clockwise to tighten and secure the
SHM to the handlebar.
To pivot the headlamp, push
the lever located under the
slider clip and rotate the
headlamp to the desired
position.
Inserting The Headlamp Into The Handlebar And Helmet Mounts
Insert the headlamp into the handlebar or helmet
mount slider clip from the rear
forward. Gently rocking the
lamp as you slide it may help.
Do not push the release lever
when inserting the headlamp
into the slider clip; let the lamp
snap into place by itself.
To remove the headlamp, push
the release lever and slide the
lamp backward.
Note: After mounting the headlamp, adjust it so the beam
illuminates the road properly without distracting oncoming
riders.
Helmet Mount
1. Unclamp the straps on each side of the helmet mount
and pull them free.
2. Position the plastic mounting
plate as close to the centerline
of the helmet as possible,
orienting the parallel grooves on
the slider clip to the rear.
3. Feed each strap into and out of two
helmet vents, circling each strap back
to the upper edge of the corresponding clamp.
4. Fasten the straps by inserting them into the clamps and snap
them shut.
OPERATION
1. Connect the headlamp cable to the battery.
2. Press and release the headlamp power button to turn the
light on. Cycle through the three brightness levels by
pressing and releasing the power button.
3. To access the daylight safety ash modes, press and hold
the power button until the headlamp starts to ash.
4. With the headlamp in ash mode, press and release the
power button to access Beacon, S.O.S. or Walk. From walk
mode you can access normal power by pressing and
releasing the power button.
5. To turn the headlamp o from normal, ash or walk modes,
press and hold the power button until the headlamp shuts o.
6. Always disconnect the battery from the headlamp when
transporting the light system to prevent accidentally
turning on the headlamp which may cause overheating
and potential damage from high heat or even a risk of re.