Nitroset NTS805 Series User manual

Remember to read the NTS805 Series Operation & Safety Manual for detailed
procedures of troubleshooting, tool assembly, disassembly and cleaning.
Check the thickness and type of base material before fastening. Follow your
In fastening into steel substrate, the minimum thickness of substrate must
be 3/16".
WWW.NITROSET.COM
NTS805 Series Quick Start Guide
Always wear proper safety e uipment including safety glasses, hard hats,
hearing protection, and gloves while operating the tool.
Required Safety & Protective Equipment
Minimum concrete thickness is three times the fastener penetration
(ie. 3" of concrete base material is a minimum requirement for 1"
penetration).
Check Before Fastening
The NITROSET® tool is for fastening into the following base materials only:
Concrete
Structural Steel
Never attempt to fasten into any material other than those listed above.
Acceptable Base Materials
1
Adapter Installation
Note: As illustrated above, Nosepiece Gasket is inserted in the groove of the
Muzzle. Debris Cup Gasket goes between the Muzzle and Debris cup. The Red
Adapter is installed between the Muzzle and Reset Sleeve.
Muzzle Debris Cup
Gasket
Nosepiece
Gasket
Red
Adapter Debris Cup
Red
Adapter
Reset
Sleeve Muzzle Debris Cup
Note: As illustrated above, the Red Adapter is installed between the Muzzle
and Reset Sleeve.
Red
Adapter
Reset
Sleeve Muzzle Debris Cup
Note: As illustrated above, the Red Adapter is installed between the Muzzle
and Reset Sleeve.

WWW.NITROSET.COM
NTS805 Series Quick Start Guide
2
Remember to read the NTS805 Series Operation & Safety Manual for detailed
procedures of troubleshooting, tool assembly, disassembly and cleaning.
(Best used with 7/8" to 1-1/4" pin & clip)
NTS805 Adapter Usage Table
NTS805 Tool is assembled with the NTS805-10 Reset Sleeve. Please refer to
the engraved text on the reset sleeve (see illustration above). The new
threadless Muzzle can use various pin and clip assemblies with the proper
Red Adapter.
805
Adapter
Requirement
No Adapter
With Red
Adapter
STT14
CLR14-222
CLR38-222
CLR14222-BRT114
CLR14222-BRT2
CLAS525
CLSUPL525
CLRHD14-525
CLRHD38-525
CLRHD14-525-BRT114
CLRHD38-525-BRT2
CLT219
CLU222
CLC12-222
CLC34-222
CLC38-222
CLC1E-222
PIN219
PIN219T
PIN222
PIN222W
PIN222SW
PIN525
PIN532NW
Pin Pin & Clip Assembly
Fastener
Type
CLAS532
CLSUPL532

Remember to read the NTS805 Series Operation & Safety Manual for detailed
procedures of troubleshooting, tool assembly, disassembly and cleaning.
WWW.NITROSET.COM
NTS805 Series Quick Start Guide
3
(Best used with 1/2" to 1" pin & clip)
Adapter
Requirement
No Adapter
With Red
Adapter CLAS532
CLSUPL532
CLT219
CLR14-222
CLR38-222
CLR14222-BRT114
CLR14222-BRT2
CLAS525
CLSUPL525
CLRHD14-525
CLRHD38-525
CLRHD14-525-BRT114
CLRHD38-525-BRT2
CLU222
CLC12-222
CLC34-222
CLC38-222
CLC1E-222
PIK313
PIK316
PIN219
PIN219T
PIN222
PIN222W
PIN222SW
PIN525
PIN532NW
Pin Pin & Clip Assembly
Fastener
Type
NTS805-S Adapter Usage Table
NTS805-S Tool is assembled with the NTS805-10-S Reset Sleeve. Please
refer to the engraved text on the reset sleeve (see illustration above).
The new threadless Muzzle can use various pin and clip assemblies
with the proper Red Adapter.
805-S

1. Check the tool and install the Spall Guard to the nosepiece.
2. Select the proper adapter for your pin or clip (see Adapter Usage Table).
3. Reset the tool before inserting the fastener to ensure the muzzle barrel is
clear of any debris.
4. Insert the fastener fully into the muzzle of the tool. Fasteners must be fully
seated in muzzle to ensure proper actuation.
(Hold reset sleeve while inserting fasteners.)
WWW.NITROSET.COM
Loading and Actuating Instructions
5. Place the NITROSET® tool perpendicular against the fastening surface.
A) Pull back front of muzzle until the firing guide is flush with the muzzle.
B) inserting new fastener assembly.
6.
procedure to minimize spalling and noise.
7. Reset the tool to ensure the muzzle barrel is clear of debris. Repeat
Steps 3 to 6 for further use.
If the tool fails to fasten, remove the spent fastener assembly while pointing
the tool away from yourself and any bystanders.
* In case of jammed fasteners – Refer to Troubleshooting Guide in the manual.
IMPORTANT: DO NOT BOUNCE FIRE THE TOOL!
•If the fastener assembly cannot be inserted into the muzzle, do not
and cause damage. Fasteners that cannot be inserted should be
removed and discarded appropriately.
•Cracked concrete may cause loud noise when using the tool.
•Fasteners should not be driven close to the edge of the base substrate.
Always maintain a distance of at least 3" from the concrete edge or 1"
from the steel edge.
WARNINGS
NTS805 Series Quick Start Guide
Remember to read the NTS805 Series Operation & Safety Manual for detailed
procedures of troubleshooting, tool assembly, disassembly and cleaning.
4