NobleChairs HERO Series User manual

HERO Series - Assembly Instructions

1x Allen Key
1
Read over the manual before you begin.
Two people are suggested for assembly.
CONTENT CHECKLIST
2x Philips Head Screw Screw Kit:
4x M8 Screw (20mm)
4x Split Washer
4x Washer
1x Neck Pillow 1x Lumbar Pillow
1x Wheel Base 1x Chair Base 1x Backrest
4x M8 Screw (30mm) with
pre-mounted Washers
1x Tilt Mechanism 5x Caster 1x Hydraulic Gas Lift 1x Hydraulic Sleeve 2x Side Cover 2x Lever Cover

5 6
56
1
1
2
2
3
3
4
4
2
WHEELBASE INSTALLATION
TILT MECHANISM INSTALLATION
Place the CHAIR BASE upside-down on a soft
surface and position the TILT MECHANISM in the
correct direction.
Insert the 5 CASTERS into the WHEEL BASE.
Push firmly to lock them into place.
Install the TILT MECHANISM by diagonally tightening
the screws into the CHAIR BASE with the ALLEN KEY.
Position the HYDRAULICS into the WHEEL BASE and place
the HYDRAULIC SLEEVE over it.
Place a SPLIT WASHER and then a WASHER onto
each of the 4 M8 SCREWS.
Place plastic LEVER COVERS onto metal handels,
align and push evenly into place.

7 8
7 8
10
9
10
9
3
CHAIRBASE INSTALLATION
Align the top of the HYDRAULICS into the bottom of the
TILT MECHANISM.
Push and sit down on the seat to lock it into place.
BACKREST INSTALLATION
Using the ALLEN KEY, unscrew the 4 M8 (30mm) pre-mounted
screws and washers on the side of the backrest.
Push the lever from below, with enough force to ensure that the mounting bracket snaps forward.
Keep your hands clear of the bracket during this process to avoid injury.
Push back the mounting bracket to roughly a 90° for easier backrest mounting.

11
12
11 12
13
13
4
BACKREST INSTALLATION
Starting with the right side, attach the backrest to the metal
brackets with the 4 M8 (30mm) screws using the ALLEN KEY.
While firmly pushing SIDE COVERS into place, use the
ALLEN KEY to secure the SIDE COVERS with the 2 PHIL-
IPS HEAD SCREWS.
BACKREST INSTALLATION
Attach the NECK PILLOW by sliding
its elastic band around the headrest
of the chair.

5
14
14
15
15
16
16
17
17
18
18
4D ARMREST ADJUSTMENTS
Starting with the right side, attach the backrest to the metal
brackets with the 4 M8 (30mm) screws using the ALLEN KEY.
Use the appropiate function to adjust the armrests.
Use the right lever to adjust the chair’s height.
TILT ADJUSTMENT
Turn the cylinder knob under the chair clockwise to tighten the
seat‘s rockability and counterclockwise to loosen it. Adjust
according to your own weight.
Use the left lever to lock/unlock the tilt mechanism.

20
20
6
19
19
SEATING ADJUSTMENT
Pull up on the lever and slowly lean back until the
preferred position is achieved.
Adjust the chair‘s lumbar support by using the knob
on the right side of the backrest.
Care Instructions
Keep noblechairs tidy by vacuuming its seams with a crevice tool.
Dust regularly using a clean, lint-free, slightly damp soft cloth and wipe the area clean.
Avoid direct sunlight and keep away from heat sources to protect its leather.
Clean spills quickly. Blot away with a clean cloth, but do not rub.
Clean the casters by wiping off dirt with a scrub brush. Vacuum out dust caught inside of the wheels.
For further cleaning, pull off the wheels and wipe them down with a surface cleaner and a clean rag.
Push firmly to lock them back into place.
Safety Information
The maximum recommended user weight of the HERO Series is up to 150kg or 330.7 pounds.
Don’t use noblechairs in an abusive manner. noblechairs is not liable for any damages resulting from
improper assembly and usage.
Return/Exchange Policy
The original packaging can be conveniently reused for a noblechairs return or exchange.
noblechairs accepts returns that are properly packaged.