Noblelift PS35LSL manual 







Version 03/2017
PS 35/44LSL-SMS-001-US
INSTRUCTION HANDBOOK
Electric Stacker
WARNING
Do not use the electric truck before reading
and understanding these operating
instructions.
NOTE:
Please check the designation of your
present type at the last page of this
document as well as on the ID-plate.
Keep for future reference.

1

2
FOREWORD
Operating this truck requires knowledge which can be acquired from this instruction handbook. This
handbook must be kept available throughout the entire period of use of the industrial truck.
IT IS LAW; YOU MUST BE TRAINED AND CERTIFIED TO OPERATE THIS TRUCK!
READ AND OBEY ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL AND
ON THE TRUCK!
Only properly trained operators are allowed to operate a powered industrial truck. Your employer
must train you and certify, that you are qualified to operate this truck (required by OSHA § 1910.178).
The training must satisfy OSHArequirements and as minimum the topics mentioned in this handbook.
Depending on the context in this operating manual, the user can refer to several people, including the
owner of the truck, anyone who leases or borrows this truck, and the operator as defined in ASME
B56.1. Please pay attention to the section in ASME B56.1 concerning the operator. In this standard, it
is defined that the safe operation is the responsibility of the operator (ASME B56.1-2003, Part II,
section 5.1.1). You and others can be seriously injured or even killed if you don’t use this truck
correctly. Before operating your truck, inspect your truck and ensure that it is in correct working order.
This truck was designed and built to current industry and government standards. For more
information see following:
- ASME B56.1 (American Society of Mechanical Engineers)
- OSHA §1910.178 (Occupational Safety and Health Act)
- UL 583 (Underwriters Laboratory)
- ANSI Z535.4 (American National Standards Institute)
This sign indicates hazard situations, if not avoided, will result in serious injury or
death. The instructions or precautions to this message must be observed to avoid the potential risk of
injury or death.
If not followed, warning indicates hazard situations which may lead to moderate
injury. The instructions or precautions to this message must be observed to avoid the potential risk of
injury or death.
If not followed, caution indicated situations which may lead to minor injury.
Instructions or precautions must be observed to avoid minor injury.

3
TABLE OF CONTENTS
1. CORRECTAPPLICATION................................................................................................................4
2. DESCRIPTION OF THE STACKER..................................................................................................5
a. Overview of the main components................................................................................................5
b. Main technical data .......................................................................................................................6
c. Description of the safety devices and warning labels(US- market) ...............................................9
d. Identification plate.......................................................................................................................11
3. WARNINGS, RESIDUAL RISK AND ASFETY INSTRUCTIONS ....................................................11
4. COMMISSIONING, TRANSPORTING, DECOMMISSIONING........................................................13
a. Commissioning............................................................................................................................13
b. Lifting/ transportation...................................................................................................................13
c. Decommissioning........................................................................................................................14
5. DAILY INSPECTION.......................................................................................................................14
6. OPERATING INSTRUCTIONS.......................................................................................................14
a. Parking........................................................................................................................................15
b. Residual lift diagram....................................................................................................................15
c. Lifting...........................................................................................................................................15
d. Lowering......................................................................................................................................15
e. Travelling.....................................................................................................................................15
f. Steering.......................................................................................................................................16
g. Braking........................................................................................................................................16
h. Malfunctions................................................................................................................................17
i. Emergency..................................................................................................................................17
j. Fork adjustment（PS 35L SL、PS 44L SL）..............................................................................17
k. Fork replacement（PS 35L SL、PS 44L SL）............................................................................18
l. Leg adjustment（PS 35L SL、PS 44L SL）...............................................................................18
7. BATTERY CHANGING AND REPLACEMENT...............................................................................18
a. Replacement...............................................................................................................................19
b. Battery indicator..........................................................................................................................20
c. Charging......................................................................................................................................20
8. REGULAR MAINTENANCE ...........................................................................................................21
a. Maintenance checklist.................................................................................................................21
b. Lubricating points........................................................................................................................22
c. Check and refill hydraulic oil........................................................................................................23
d. Checking electrical fuses ............................................................................................................23
e. Removing, reattaching guarding .................................................................................................23
9. TROUBLE SHOOTING...................................................................................................................23
10. WIRING/ CIRCUIT DIAGRAM........................................................................................................25
a. Electrical circuit diagram .............................................................................................................25
b. Hydraulic circuit...........................................................................................................................26

4
1. CORRECT APPLICATION
It is only allowed to use this electric stacker according to this instruction handbook.
The trucks described in this handbook are self propelled pedestrian controlled electric power stacker,
with electrically powered low height lifting function. The trucks are designed for stacking operations in
dedicated racking by lifting and lowering the palletized load up to the desired lifting height.
A wrong usage can cause human injuries or can damage equipment.
The operator/ the operating company has to ensure the correct usage and has to ensure, that this truck
is used only by staff, which is trained and authorized to use this truck.
The truck has to be used on substantially firm, smooth, prepared, level and adequate surfaces. The truck
is intended to be used for indoor applications with ambient temperatures between +5C and + 40C and
for intensive operations without crossing permanent obstacles or potholes. Operating on ramps is not
allowed. While operating, the load must be placed approximately on the longitudinal centre plane of the
stacker.
Lifting or transporting people is forbidden.If travelling the load must be lowered to the lifting point.
It is not allowed to use this truck on tail lifts or loading ramps.
The capacity is marked on the load diagram as well on the Identification plate. The operator has to
consider the warnings and safety instructions.
Operating lighting must be minimum 50 Lux.
Modification
No modifications or alterations to this truck which may affect, for example, capacity, stability or safety
requirements of the truck, shall be made without the prior written approval of the original truck
manufacturer, its authorized representative, or a successor thereof. This includes changes affecting, for
example braking, steering, visibility and the addition of removable attachments. When the manufacturer
or its successor approve a modification or alteration, they shall also make and approve appropriate
changes to capacity plate, decals, tags and operation and maintenance handbooks.
By not observing these instructions, the warranty becomes void.

5
Fig. 1: Overview main components
2. DESCRIPTION OF THE STACKER
a.
Overview of the main components
1. Main cover
2. Handle
3. Safety (belly) button
4. Accelerator (butterfly button)
5. Battery cover
6. Emergency button
7. Discharge indicator and charging indicating
LED
8. Key switch
9. Load roller
10. Pallet
11. Load backrest
12. Protective board
13. Mast
14. Chassis
15. Hydraulic system

6
b. Main technical data
Fig. 2: Technical data
Table1: Main technical data for standard version
Type sheet for industrial truck acc. to VDI 2198
Distinguishing mark
1.2 Manufacturer`s type designation PS35L SL(181) PS44L SL(181)
1.3 Power (battery ,diesel, petrol, gas, manual) Battery
1.4 Operator type Pedestrian
1.5 Load Capacity / rated load Q(lbs) 3520 4400
1.6 Load centre distance C(in) 23.6
1.8 Load distance ,centre of drive axle to fork x(in) 27.2 26.5
1.9 Wheelbase y(in) 54.3 58.7
Weight
2.1 Service weight lbs 3219 3748
2.2 Axle loading, laden front/rear lbs 2205/4542 2425/5732
2.3 Axle loading, unladen front/rear lbs 2249/970 2227/1521

7
Tires, chassis
3.1 Tires Polyurethane (PU)
3.2 Tire size, front xW (in) 9×2.95
3.3 Tire size, rear xW (in) 3.3×3
3.4 Additional wheels(dimensions) xW (in) 5.9x2
3.5 Wheels, number front/rear(x=driven wheels) 1x+1/4
3.6 Track, front b
10
(in) 20.5
3.7 Track, rear b
11
(in) 43.1-54.9
Dimensions
4.2 Lowered mast height h
1
(in) 83 88
4.3 Free Lift height h
2
(in) 60 60
4.4 Lift height h
3
(in) 178 178
4.5 Extended mast height h
4
(in) 200 205
4.9 Height of tiller in drive position min./ max. h
14
(in) 33.5/54.5
4.15 Height, lowered h
13
(in) 1.97
4.19 Overall length l
1
(in) 78.9 84.1
4.20 Length to face of forks l
2
(in) 33.6 38.8
4.21 Overall width b
1
(in) 32.3/(48-59.8)
4.22 Fork dimensions s/e/l (in) 1.6x4.7x45.3
4.25 Distance between fork-arms b
5
(in) 10-28.7
4.32 Ground clearance, centre of wheelbase m
2
(in) 1.3
4.33 Aisle width for pallets 1000X1200 crossways Ast(in) 100.6 105.3
4.34 Aisle width for pallets 800X1200 lengthways Ast(in) 99.5 104.4
4.35 Turning radius Wa(in) 66.1 70.5
Performance
data
5.1 Travel speed, laden/ unladen mph 3.5/3.7 3.4/3.7
5.2 Lift speed, laden/ unladen fpm 25.6/39.4 25.6/39.4
5.3 Lowering speed, laden/ unladen fpm 39.4/27.6 39.4/27.6
5.8 Max. gradeability, laden/ unladen % 6/12 6/10
5.10 Service brake Electromagnetic
Electric- engine
6.1 Drive motor rating S2 60min HP 1.7 2.3
6.2 Lift motor rating at S3 10% HP 4.3 4.3
6.3 Battery acc. to DIN 43531/35/36 A, B, C, no 3VBS 3PZS
6.4 Battery voltage, nominal capacity K5 V/Ah 24/270 24/350
6.5 Battery weight lbs 506 634
6.6 Energy consumption acc: to VDI cycle kWh/h 1.59 1.79
Addition
al data
8.1 Type of drive control AC- speed control
8.4 Sound level at driver`s ear acc. to EN 12053 dB(A) 69
Table 2:Mast table
Designation
Lowered mast
height
h1(in)
Free Lift height
h2(in) Lift height h3(in)
Extended mast
height
h4(in)
PS 35L SL
Two stage mast 77 — 111 133

8
83 — 123 145
91 — 139 161
Two stage mast FFL
(Full-Free-Lift)
77 55.5 111 133
83 61.4 123 145
91 69.3 139 161
Three stage mast 79 — 167 188
83 — 178 200
Three stage mast
FFL
(Full-Free-Lift)
75 52 155 176
79 55.9 167 188
83 59.8 178 200
PS 44L SL
Two stage mast
82 — 111 138
88 — 123
150
96 — 139
165
Two stage mast FFL
(Full-Free-Lift)
78 51.6 104 130
82 55.5 111 138
88 61.4 123 150
96 69.3 139 165
Three stage mast 84 — 167 193
88 — 178 205
Three stage mast
FFL
(Full-Free-Lift)
78 51.6 155 181
84 55.9 167 193
88 59.8 178 205

9
c. Description of the safety devices and warning labels(US- market)
A. Crane hook label
C. Residual lift capacity sticker
E. Identification plate (ID-plate)
F. Sticker to read and follow these instructions
G. Sign oil filling point
H. Sign danger not riding
I.Sign danger being crushed
J. Sign warning stay clear stop truck
L. Sign danger battery
M. Sign warning electrical devices
N. Sign not under, on forks
The truck has an emergency button (6) which stops all lifting-, lowering-, driving- functions and engages
the failsafe electromagnetic brake when it is pushed. By pulling this button, the truck can be operated
after the controller checked the functions. Before operating, insert the key and turn the switch (8)
clockwise. To prevent against unauthorized access, turn the key anti-clockwise and remove it, if you not
operate this truck. The truck is equipped with a safety (belly) button (3) which switches the driving
function away from the operator, if the truck travels towards the operator and the tiller is activated in the
tillers operating zone. Follow also the instructions given on the decals. Replace the decals if they are
damaged or missing.
Fig.3: Safety and warning labels

10
Sign read and follow this instruction (F)
Sign oil filling point (G)
Sign danger not riding (H)
Sign danger being crushed (I)
Sign warning stay clear stop truck (J)
Sign danger battery (L)
Sign warning electrical devices (M)
Sign not under, on forks (N)

11
d. Identification plate
1 Designation, type
2 Serial number
3 Rated capacity in lbs
4 Supply voltage in V
5 Own mass (self weight) in kg without battery
6 Max. battery capacity
7 Battery ID
8 Name and address of manufacturer)
9 Hour rate
10 Battery weight minimum/ maximum
11 Nominal power in kW
12 Load center distance
13 Manufacturing date
14 Option
3. WARNINGS, RESIDUAL RISK AND ASFETY INSTRUCTIONS
DO NOT
Drive outside the stacking operation with a lifted load higher than the lifting point.
Put foot or hand under or into the lifting mechanism.
Allow other person than the operator to stand in front of or behind the truck when it is
moving or lifting/lowering.
Overload the truck.
Put foot in front of the wheels, injury could result.
Lift people. People could fall down and suffer severe injury.
Push or pull loads.
Use this truck on ramps.
Use the truck without a removed protective screen (fig.1, pos. 17/ guarding).
Side or end load. Load must be distributed evenly on the forks.
Use the truck with unstable, unbalanced not stable load.
Fig. 4: Identification plate

12
Use truck without manufacturer’s written consent.
Lifted loads could become unstable at wind forces. In the case of wind forces do not
lift the load if there is any influence to the stability
Watch difference in floor levels when driving. Load could fall down or the truck could get uncontrollable.
Keep watching the condition of load. Stop operating the truck if load becomes unstable. Brake the truck
and activate the emergency button (6) by pushing when sliding load on or off the truck. If the truck has
any malfunctions, follow chapter 8.
Practice maintenance work according to regular inspection. This truck is not designed to be water
resistant. Use the truck under dry condition. Prolonged continuous operation might cause damage of the
power pack. Stop operation if temperature of hydraulic oil is too high.
When operating the truck, the operator has to wear safety shoes.
The truck is intended to be used for indoor applications with ambient temperatures
between +5C and + 40C.
The operating lighting must be minimum 50 Lux.
It is not allowed to use the truck on ramps.
 To prevent unintended sudden movements when not operating the truck (i.e. from another
person, etc.) switch off the truck and remove the key.

13
4. COMMISSIONING, TRANSPORTING, DECOMMISSIONING
a.
Commissioning
Table 3: Commissioning data(For different models, the commissioning weight is marked on
the ID-plate )
Type PS 16L SL /
181” PS 20L SL / 181”
Commissioning
weight [lbs] 3440 3968
Version/ Lift [in] 181” 181”
For different models, the commissioning weight is marked on the ID plate.
After receiving your new truck or for re-commissioning you have to do following before (firstly) operating
the truck:
Check if are all parts included and not damaged
Eventually installation and charging the batteries (follow chapter 7)
Do the work according to the daily inspections as well as functional
checks.
b. Lifting/ transportation
For transporting, remove the load, lower the forks to the lowest position and
fix the truck safe with dedicated lifting gear according to the following figures.
Lifting
USE DEDICATED CRANE AND LIFTING EQUIPMENT
DO NOT STAND UNDER THE SWAYING LOAD
DO NOT WALK INTO THE HAZARDOUS AREA DURING LIFTING
Lower the forks and park the truck securely.
Fasten the truck according to fig.5 by fixing dedicated lashing belts to
each side of the truck’s crane hook holes and fasten the other side at the
transporting truck.
Transportation
DURING TRANSPORTATION ON A LORRY OR TRUCK
ALWAYS FASTEN THE TRUCK SECURELY
Lower the forks and park the truck on the iron plate securely. Fixe the forks
by the iron sheet with two screws. Fasten the truck by fixing dedicated
lashing belts according to fig. 6 and fasten the other side at the transporting truck.
Fig. 6: Fixing points
Fig.5: Lifting with a crane

14
c. Decommissioning
For storage, remove the load, lower the truck to the lowest position, grease all in this handbook
mentioned greasing points (regular inspection), eventual protect the truck against corrosion and dust.
Remove the batteries and jack the truck safely, so that there will be no flattening after storage.
For final decommissioning hand the truck to a designated recycling company. Oil, batteries and electric
components must be recycled due to legal regulations.
5. DAILY INSPECTION
This chapter describes pre-shift checks before putting the truck into operation.
Daily inspection is effective to find the malfunction or fault on this truck. Check the truck on the following
points before operation.
Remove load from truck and lower the forks.
DO NOT USE THE TRUCK IF ANY MALFUNCTION IS FOUND.
Check for scratches, deformation or cracks.
Check if there is any oil leakage from the cylinder.
Check the vertical creep of the truck.
Check the chain and rollers for damages or corrosion.
Check the smooth movement of the wheels.
Check the function of the emergency brake by activating the emergency button.
Check, the tiller arm- switch braking function
Check the lifting and lowering functions by operating the buttons.
Check if the protective screen has no damages and that is correctly assembled.
Check the audio warning signal.
Check if all bolts and nuts are tightened firmly.
Check the function of the key switch.
Check the speed limitation switch.
Visual check if there are any broken hoses or broken electric wires.
If supplied with a backrest extension, check it for damages and
correct assembling.
6. OPERATING INSTRUCTIONS
BEFORE OPERATING THIS TRUCK, PLEASE FOLLOW
THE WARNINGS AND SAFETY INSTRUCTIONS
(CHAPTER 3).
BEFORE OPERATING THIS TRUCK, ENSURE THAT THE
LOAD OR OTHER EQUIPMENT NOT CAUSES
INSUFFICIENT VISIBILITY!
Make sure, that the load is palletized and stable and that the daily
3
4
22
23
Fi
g
.7: Tiller o
p
eratin
g
controls
Fig.8: Key switch

15
inspection is carried out. For starting, insert the key and turn it clockwise to the “ON”- position.
Eventually before inserting the key switch (8), the emergency button (6) must be pulled carefully.
Press the horn button (22) to activate the audible warning signal.
a. Parking
DO NOT PARK THE TRUCK ON INCLINED SURFACES
Thetruck is equipped with an electromagnetic failsafe stopping and parking
brake.
Always lower the forks fully and drive the truck to a safe area. Turn the key
anti- clockwise to the “Off” – position and remove the key.
b. Residual lift diagram
The residual lift diagram indicates the maximum capacity Q [lbs] for a given
load centre c [in] and the corresponding lift height H [in] for the truck with
horizontal load.
The white markings on the mast indicate if the specific lifting limits reached.
For instance with a load centre of gravity distance c of 24in and a maximum
lift height H of 181in, the max. capacity Q is 2204lbs.
c. Lifting
DO NOT OVERLOAD THE TRUCK! THE MAXIMUM CAPACITY IS 3219/3748lbs.
LIFT ONLY CAPACITIES ACCORDING TO THE RESIDUAL LIFT DIAGRAM.
Travel with the lowered forks fully underneath the pallet and press the lifting button (fig. 7, 23) until you
reached the desired lifting height.
d. Lowering
If the forks are in the racking, firstly travel out of the racking
carefully with or without the pallet. By travelling out of the
racking, take care that the forks are not touching the racking.
Press the lowering button (fig. 7, 23) carefully.
Lower the load until the forks are clear of the pallet, then drive
the truck carefully out of the load unit.
e. Travelling
TRAVEL ON INCLINES ONLY WITH THE LOAD FACING UPHILL .
DO NOT TRAVEL ON INCLINES MORE THAN SPECIFIED WITH THE TECHNICAL
DATA.
Fig. 9: Residual lift diagram
Fig. 10: Load facing uphill

16
TRAVELLING IS ONLY ALLOWED IF THE FORKS ARE LOWERED DOWN TO THE
LIFTING POINT (<12in).
After starting the truck by turning the inserted key to the “ON”- position (fig. 8),; and eventually by pulling
the emergency button carefully, move the tiller to the operating zone (‘F’, fig.11).
Turn the accelerator button to the desired direction forward ‘Fw.’ Or backwards ‘Bw.’(fig. 11).
Control the travelling speed by moving the accelerator button (4) carefully until you reached the desired
speed.
If you move the accelerator button back to the neutral position, the controller decelerates the truck until
the truck stops. If the truck stopped, the parking brake will be engaged.
Drive carefully the truck to the destination. Watch the route conditions and adjust the travelling speed
with the accelerator- button.
f. Steering
You steer the truck by moving the tiller to the left or right side .
g. Braking
THE BRAKING PERFORMANCE DEPENDS ON THE TRACK CONDITONS AND THE
LOAD CONDITONS OF THE TRUCK
The braking function can be activated on several ways:
By moving the accelerator button (4) back to the initial ‘0’ position or by releasing the button, the
regenerative braking is activated. The truckbrakes until it stops.
By moving the accelerator button (4) from one driving direction directly to the opposite direction, the
truck brakes regenerative until it starts travelling into the opposite direction.
The truck brakes, if the tiller is moved up or down to the braking zones (‘B’). If the tiller is released,
the tiller moves automatically up to the upper baking zone (‘B’).
The truck brakes until it stops.
Fig.11: Operating direction

17
 The safety (belly) button (3) prevents the operator from being crushed. If this button is activated, the
truck decelerates and/ or starts travelling into the backwards direction (‘Bw.’) for a short distance
and stops. Please consider, that this button also operates, if the truckis not travelling and the tiller is
in the operating zone.
h. Malfunctions
If there are any malfunctions or the truck is inoperative, please stop using the truck and activate the
emergency button (6) by pushing it. If possible, park the truck on a safe area, turn the key switch (8) anti-
clockwise and remove the key.
Inform immediately the manager and, or call your service. If necessary, tow the truck out of the operating
area by using dedicated towing/ lifting equipment.
i. Emergency
In emergencies or in the event of tip over (or off dock), keep safe distance immediately. If possible push
the emergency button (6). All electrical functions will be stopped.
j. Fork adjustment（PS 35L SL、PS 44L SL）
 Not fixed and improperly adjusted forks can lead to
dangerous accidents.
 Check if the safety bolt (10) is installed before adjusting
the forks. If the safety bolt (10) is not in place, the truck
shall be prohibited to use.
 When adjusting the fork, pay attention that the distance
between each fork and outer edge of the holder should be
same.
 Clip the positioning pin into a fixi slot to avoid accidental
movement of the fork.

Load center must be located in the middle of the two forks.
Operation steps:
Park the truck securely according to the regulations.
Pulled up the positioning pin (13), make it away from the fixed slot.
Move the forks (14) to the appropriate position.
In order to ensure the operation safety of picking process, the distance
between the forks (14) should be as large as possible, and the fork position
must be symmetrical with the center line of the fork holder. Load center must
be located in the center of the forks (14).
Put down the positioning pin (13), move the forks until the positioning pin
clip into the fixing slot.
Fig.12:Adjust the forks
Fig.13:Move the forks

18
k. Fork replacement（PS 35L SL、PS 44L SL）
 There is leg injury risk when replacing the forks.
 It’s forbidden to pull the fork to the direction of the operator.
 Move the fork in the direction away from the operator.
 In order to prevent moving down, please use crane to fix heavy forks.
 Install the safety bolt (10) after replacing the forkand check whether the position of the safety bolt
is correct.
 There is leg injury risk when replacing the forks.
 It’s forbidden to pull the fork to the direction of the operator.
Operation steps:
Remove the safety bolt (10).
Release fork positioning device (11).
Move the forks to the center of fork holder and remove the
forks through the groove.
l. Leg adjustment（PS 35L SL、PS 44L SL）
 Not fixed and not properly adjusted legs can lead to dangerous accidents.
 There is leg injury risk when adjusting the legs.
 Tighten the positioning bolt (23) after adjusting the legs.
 When adjusting the legs, please pay attention that the number of positioning holes (21)exposed
on each side of the legs should be same. (as shown in Fig.16, if one side has 3 positioning
holes(21), the other side should also be 3).
Operation steps:
Park the truck securely according to the regulations.
Turn clockwise the supporting assembly(20) on both sides of the
truck until jacking up the truck.
Screwed out the positioning bolt (23).
Adjust the leg (22) until the corresponding positioning hole (21) is
adjusted to the underface of the positioning bolts (23).
When adjusting the legs, please pay attention that the number of
positioning holes (21)exposed on each side of the legs should be
same. (as shown in Fig.16, if one side has 3 positioning holes(21), the other side should also be 3).
Screw the positioning bolt (23) tightly.
Turn anti-clockwise the supporting assembly(20) on both sides of the truck until the supporting
assembly can’t be turned anymore.
7. BATTERY CHANGING AND REPLACEMENT
Only qualified personnel are allowed to service or charge the batteries. The
instructions of this handbook and from the battery- manufacturer must be observed.
The batteries are liquid acid traction batteries. Optional maintenance free batteries
Fig.14:Replace the forks
Fig.15:Adjust the legs

19
are available; for these batteries re- filling is prohibited.
Recycling of batteries undergoes national regulations. Please follow these
regulations.
By handling batteries, open fire is prohibited, gases could cause explosion!
In the area of battery charging neither burning materials nor burning liquids are
allowed. Smoking is prohibited and the area must be ventilated.
Park the truck securely before starting charging or installing/changing the batteries
Before finishing the maintenance work, make sure, that all cables are connected
correctly and that there are no disturbing towards other components of the truck.
Depending on the version, the truck is equipped with following liquid acid traction battery- type:
PS35L 1pc 3VBS 24V/ 270 Ah (C5) [29.6x6.8x25.9 (LxWxH)]
PS44L 1pc3PzS24V/ 350Ah (C5) [24.6 x 11.2 x 24.7 (LxWxH)]
IT IS ONLY ALLOWED TO USE LIQUID ACID TRACTION BATTERIES.
THE WEIGHT OF THE BATTERIES HAS AN INFLUENCE TO THE TRUCKS
OPERATING BEHAVIOR.
PLEASE CONSIDER THE MAXIMUM OPERATING
TEMPERATURE OF THE BATTERIES.
a. Replacement
Park the truck securely and switch off the stacker with the key (8) and
activate the emergency button (6). Open the battery cover and pull
out the hinge, remove the battery cover. Unscrew and remove the
battery baffle plate, pull out the battery plug (Fig.16), and take the
batteries out with a crane. The installation is in the reverse order of
the removal. Please connect the positive terminals firstly. Otherwise
the tuck could be damaged.
Fig. 16:Battery replacement